Page 1 Cover Page TRENDnet User’s Guide...
Page 2: Table Of Contents
Global Settings ....................23 Protocol ......................37 User List ......................23 Root Bridge Information ..................38 Community List ....................23 RSTP Port Settings ..................... 38 Group List ......................24 CIST Port Settings ....................39 © Copyright 2023 TRENDnet. All Rights Reserved.
Page 3 Port Binding ....................... 60 Enable Multicast Filtering .................. 51 Dial-in User ........................60 Administration ......................51 Create Dial-In Users (Local Authentication Method) ......... 60 Changing login credentials ................. 51 RADIUS ......................... 61 Logs ..........................52 © Copyright 2023 TRENDnet. All Rights Reserved.
Page 4 Backup/Restore via TFTP Settings ..............68 Diagnostics ........................69 Cable Diagnostics Test ..................69 Ping Test ........................70 Network Connectivity Test (Ping Tool) .............. 70 IPv6 Ping Test ....................... 71 Network Connectivity Test (Ping Tool) .............. 71 © Copyright 2023 TRENDnet. All Rights Reserved.
Page 5: Product Overview
IP surveillance system performance, and minimize network traffic. TL2-F7120 TRENDnet’s 10G SFP+ switch features 12 x 10GSFP+ slots for high-speed network uplinks or downlink NAS/access server connections, providing a cost-effective solution in adding 10G link capability to an SMB network.
Page 6 Product Hardware Features Sends larger packets, or Jumbo Frames (up to 9KB) for increased performance Rackmount Design Save rack space by mounting 2 x TL2-F7120 into 1U space with the optional ETH-F71 dual mount bracket (sold separately) IPv6 Ready This 10G SFP+ switch supports Ipv6 configuration and Ipv6 neighbor discovery...
Page 7: Key Features
: The link speed is established at 1Gbps (1000Mbps). (Orange) (Left side LED per slot) Blinking The SFP/SFP+ slot is transmitting or receiving data. (Right side LED per slot) The SFP/SFP+ link is disconnected or not established. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 9: Switch Installation
• When installing the Switch on a level surface, attach the rubber feet to the Then, use screws provided with the equipment rack to mount each switch in the rack. bottom of each device. The rubber feet cushion the hub and protect the hub case from scratching. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 10: Basic Installation
192.168.10.x (e.g. 192.168.10.25) and a subnet mask of 255.255.255.0. 4. Open your web browser, and type the IP address of the switch in the address bar, and then press Enter. The default IP address is 192.168.10.200. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 11 8. Configure the switch IP address settings to be within your network subnet, then click Apply. Note: You may need to modify the static IP address settings of your computer’s network adapter to IP address settings within your subnet in order to regain access to the switch. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 13: Configure Your Switch (Web-Based Ui)
• Runtime Image: The current software or firmware version your switch is running. Note: User Name and Password are case sensitive. Clicking the Upgrade Firmware button will open the firmware update page to upload device firmware. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 14 • Subnet Mask – Displays the current IPv4 subnet mask assigned to your switch. • Hardware Version: Displays your switch hardware version. • Gateway – Displays the current gateway address assigned to your switch. • © Copyright 2023 TRENDnet. All Rights Reserved.
Page 15 Settings > System Information section. address configuration. • IPv6 DHCP Client Mode: Displays if the switch is to IPv6 DHCP client mode automatic IPv6 addressing. Static indicates that the switch using a static IPv6 address configuration. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 16: Real-Time Statistics
• UC Tx: Total amount of unicast frames transmitted the port. MC Tx: Total amount of multicast frames transmitted the port. • • BC Tx: Total amount of broadcast frames transmitted the port. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 17: System
• Configuration: Click the drop-down list and select Static to manually specify your IP address settings or DHCP to allow your switch to obtain IP address settings automatically from a DHCP server on your network. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 19: Set Your Ipv6 Settings
IPv6 default gateway address. Stateless DHCPv6: Obtain configuration settings automatically from a stateless DHCPv6 server along SLAAC server. Stateful DHCPv6: Obtain IPv6 address and configuration settings automatically from stateful DHCPv6 server. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 20: Create Additional Ipv4 Address Interfaces
3. To add a new IPv4 address interface and assign to a VLAN, click Add. Note: Before you can assign IPv4 address interfaces to VLANs, you must create additional VLAN first. You can create VLANs under the Network > VLAN section. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 21: Create Additional Ipv6 Address Interfaces
3. To add a new IPv6 address interface and assign to a VLAN, click Add. Note: Before you can assign IPv6 address interfaces to VLANs, you must create additional VLAN first. You can create VLANs under the Network > VLAN section. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 22: Configure Arp Settings
Max Retries: Configures the max. number of retries to resolve ARP requests. • • Timeout: Configures the amount of time the dynamic ARP entry is removed from the ARP table when ARP cannot be resolved. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 23 MAC Address: Enter the MAC address for the static ARP entry. • Interface: Click the interface drop-down list and select the VLAN to assign the • static ARP entry. Click Apply to save the static ARP entry to the ARP table. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 24 • 123. Click Apply to save the configuration settings. Current Time: Displays the current system time and date. • SNTP: Select enabled to obtain time and date settings from an SNTP server. • © Copyright 2023 TRENDnet. All Rights Reserved.
Page 25 Interface: Click the drop-down list and select the VLAN interface to assign the IPv6 neighbor entry. Click Apply to save the entry to the table. To add a new static IPv6 neighbor entry that does not exist, click on Add. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 26 0 to set no limit on idle time out. information to view. You can click Refresh to force refresh of the displayed content or clear to delete all statistics. Click Apply to save the web idle timeout settings. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 27: Snmp
3. Click Add to add username to the user list. 4. To add a new entry, click the Add button 4. Review the settings and click Apply. 5. Review the settings and click Apply, © Copyright 2023 TRENDnet. All Rights Reserved.
Page 28: Access List
Security Mode: Select from the drop down menu the level of security Read View: Input the items that are readable for this group • Write View: Input the items that can be modified by this group • © Copyright 2023 TRENDnet. All Rights Reserved.
Page 29: View List
Owner: This parameter is used to identify the person who created an entry. It is primarily intended for switches that are managed by more than one person, and is an optional field. In the list, you can click Delete to delete the entry. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 30: Event List
1. Log into your switch management page (see “Access your switch management page” Click Apply to save settings. on page 9). 2. Click on System, click on RMON, and click on Event Log Table. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 31: Alarm List
Index: This parameter specifies the ID number of the new group. The range is 1 • to 65535. Sample Interval: This parameter specifies the time (in seconds) over which the • data is sampled. Its range is 1 to 2147483647 seconds. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 32: History
1. Log into your switch management page (see “Access your switch management page” on page 9). 2. Click on System, click on RMON, and click on History. 3. Review the settings. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 33: History Log Table
System > MAC Address Table > Dynamic MAC Address 1. Log into your switch management page (see “Access your switch management page” on page 9). 2. Click on System, click on MAC Address Table, and click on Dynamic MAC Address. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 34: Mac Aging Time
2. Click on System, click on SFP Module Information , and select either Module or DDM. 3. Module and DDM displays additional information of the SFP module that’s connected in the SFP slots. Module: © Copyright 2023 TRENDnet. All Rights Reserved.
Page 35: Network
You can use this parameter to set the speed and duplex mode of a port. • Description: This parameter offers the ability to name the device that’s The possible settings are: connected to it © Copyright 2023 TRENDnet. All Rights Reserved.
Page 36: Port Isolation
Port section or you could click All to copy data received on all ports. To copy data transmitted on specific port, select the port number under the Egress Port section or you could click All to copy data transmitted on all ports. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 37: Jumbo Frames
9). 2. Click on Network, then click on Physical Interface, and click on Jumbo Frames. 3. Enter the size of the Jumbo Frames to be accepted by the switch (in Bytes). © Copyright 2023 TRENDnet. All Rights Reserved.
Page 38: Vlan Settings
VID settings accordingly for untagged VLAN ports under Bridge > VLAN > Port Settings. (e.g. If the VID for the VLAN is 2, the PVID should also be set to 2) Select the untagged VLAN ports to add to the new VLAN. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 39: Pvid & Ingress Filter
Untagged– The port can accept untagged frames and frames with tagged priority information only such as 802.1p. Note: Modifying settings in the row marked All, will apply the settings to all ports. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 40: Gvrp
GARPLeaveTimer >= (GARPJoinTimer X 2) + 10 3. Select Enabled under GARP VLAN Registration Protocol to to activate GVRP or disabled to deactivate GVRP. Click Apply to save the settings. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 41: Spanning Tree
BPDUs that the bridge can send per second. Its range is 1 - 10. Hello Time: The Hello Time is frequency with which the root bridge sends out a • BPDU. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 42: Root Bridge Information
1. Log into your switch management page (see “Access your switch management page” on page 9). 2. Click on Network, click on Spanning Tree, click on Global Settings, and click on Root Bridge Information. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 43: Cist Port Settings
Selecting Yes indicates a P2P shared link is available. Selecting No means the port cannot maintain a P2P link. • Migration: Enabled indicates the port is configured to accept RSTP and Disabled indicates the port is not configured to accept RSTP. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 44: Mst
Priority: Select the new priority in the Priority field from the drop down menu options. The user may set a priority value between 0-61440. 1. Log into your switch management page (see “Access your switch management page” on page 9). © Copyright 2023 TRENDnet. All Rights Reserved.
Page 45: Mst Port Settings
Internal Path Cost (0 = Auto) - This is the port cost used by MSTP when calculating path cost to the root bridge. Port Status: Enable or disable the current settings configured for the selected port. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 46: Trunk
Data Unit) packets. This setting enables the dynamic LACP feature for the trunk. • Static - Enables static port trunking and disables the LACP feature for the trunk. (Static link aggregation). • Disable - Disables the static port trunk and disables the LACP feature. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 48: Vlan Settings
IGMP Snooping Status – Click the drop-down list and select Enabled to enable the IGMP snooping or Disabled to disable the feature • Version – Click the drop-down list and select IGMP version Querier Settings Network > IGMP Snooping > Querier Settings © Copyright 2023 TRENDnet. All Rights Reserved.
Page 49: Router Settings
2. Click on Network, click on MLD Snooping, and click on Port Settings. 3. Review the settings. Click Apply to save the settings. • Fast Leave – Select Enabled to enable Fast Leave from the selected port or Disabled to disable the feature © Copyright 2023 TRENDnet. All Rights Reserved.
Page 50: Vlan Settings
Version – Click the drop-down list and select IGMP version Router Settings Network > MLD Snooping > Router Settings 1. Log into your switch management page (see “Access your switch management page” on page 5). © Copyright 2023 TRENDnet. All Rights Reserved.
Page 51: Loopback Detection
VLAN. This is important when the Auto-Detection feature for a port and 4. At the top right panel, click the Apply button to save the changes to the Flash. is a dynamic voice VLAN port. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 52: Global Settings
Note: Any Static tagged members of the voice VLAN are required to have the port VLAN ID (PVID) configured to be the same as the voice VLAN ID. This insures that all untagged © Copyright 2023 TRENDnet. All Rights Reserved.
Page 53: Oui Settings
3. Select from the table to use a pre-defined OUI. To modify a pre-defined OUI, click Edit on the far right of the table. To delete an OUI from this table, select the OUI Index and click Delete. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 54: Lldp
System Description: This parameter lists the product name of the switch. You • cannot change this parameter • Capabilities Supported: This parameter lists the capabailities that can be supported. You cannot change this parameter. Configure the LLDP Parameter Settings © Copyright 2023 TRENDnet. All Rights Reserved.
Page 55: Multicast Filtering
2. Click on Network and click on Multicast Filtering. 3. Select Enabled to enable this feature or Disabled to disable Multicast Filtering 4. At the top right panel, click the Apply button to save the changes to the Flash. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 56: Settings
Clear: Erases all log files 4. Review the settings and click Apply to save the changes to the Flash. • IP/Hostname: Enter the IP address of the location you want the Log files to go © Copyright 2023 TRENDnet. All Rights Reserved.
Page 57: Qos (Quality Of Service)
WRR (Weighted RoundRobin) - The port transmits a set number of packets • from each queue, in a round robin fashion, so that each has a chance to transmit traffic. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 58: Dscp Mapping
2. Click on QoS and click on DSCP Mapping. 3. Select the relevant DSCP value to configure and click Edit to modify the Queue ID for the selected DSCP value. Click Apply to save the settings. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 59: Port Cos
Egress – Select Enabled to enable Egress Rate Limiting or Disabled to disable this feature. Egress Rate (kbps) – Enter the egress rate limit value. • 4. At the bottom of the left hand panel, click Apply. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 60: Storm Control
Note: Modifying settings in the row marked All, will apply the settings to all ports. Timeout Security > Access > Web 1. Log into your switch management page (see “Access your switch management page” on page 5). © Copyright 2023 TRENDnet. All Rights Reserved.
Page 61: Cli Timeout
SSH Service: Select Enabled to enable Telnet or Disabled to disable this Access Control: Creating MAC ACL feature. Security > Access Control > MAC ACL 1. Log into your switch management page (see “Access your switch management page” on page 9). © Copyright 2023 TRENDnet. All Rights Reserved.
Page 62: Access Control: Configuring Mac Acl
4. Input a name in the field and click Apply to save your new ACL name to the Flash. specified ACL criteria. • VLAN ID: Enter the VLAN ID to associate with this MAC ACL. • Source MAC: Input the source of the MAC address © Copyright 2023 TRENDnet. All Rights Reserved.
Page 63: Access Control: Configuring Ipv4 Acl
4. Input a name in the field and click Apply to save your new ACL name to the Flash. • Source IP Mask & Destination IP Mask: Enter the mask of the Source MAC and Destination MAC. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 64: Access Control: Configuring Ipv6 Acl
Source IP Mask & Destination IP Mask: Enter the mask of the Source MAC and Dial-in User • Destination MAC. Create Dial-In Users (Local Authentication Method) • Protocol: Select the protocol Security > Dial-in User Select from list: Select from a pre-defined list below under “IGMP List” © Copyright 2023 TRENDnet. All Rights Reserved.
Page 65: Radius
Retry – Enter the max number of retries before it stops trying to recover • Server Priority – Enter the RADIUS Server priority (Highest: 1, Lowest: 5). Click Apply to add the entry to the table. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 66: Tacacs
9). 2. Click on Security and click on TACACS+. 3. Click Add to create a new TACAS+ 4. Review the settings. Server IP– Enter the TACACS+ Server IP address. • © Copyright 2023 TRENDnet. All Rights Reserved.
Page 67: Dhcp Snooping
Disable - The MAC address of each ingress ARP packet is not validated against the Binding Table. All ARP packets are forwarded through the switch without regard to the IP and MAC Address information in the packet header. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 68: Trusted Port Interfaces
Untrusted: This parameter defines the port as untrusted for the DHCP Snooping feature. • Trusted: This parameter defines the port as trusted for the DHCP Snooping feature. Note: You can select the row labeled ALL to apply settings to all ports. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 69: Denial Of Service
4. Click Apply to save the settings to the Flash. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 70: Tools
TRENDnet may periodically release firmware upgrades that may add features or fix 3. Select the firmware Upgrade Method (HTTPS or TFTP). problems associated with your TRENDnet switch model and version. To check if there is a firmware upgrade available for your device, please check your TRENDnet model and 4.
Page 71: Firmware Upgrade Via Tftp Settings
Created Time: When the firmware was loaded onto the partition • TFTP Server: Enter the IP address of your TFTP server. • File Name: Enter the firmware filename with extension. (.hex) • 6. Click Apply to start the firmware upgrade. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 72: Config Backup Restore
3. Make sure your TFTP server is running and note the IP address of your server and 2. Click on Tools, click on Firmware and click on Backup/Restore. firmware file name. The TFTP server should be in the same IP subnet as the switch. 3. Select Restore under Backup/Restore © Copyright 2023 TRENDnet. All Rights Reserved.
Page 73: Diagnostics
Method: Select TFTP as the method of restoring up your configuration • TFTP Server IP: Enter the IP address of your TFTP server • • TFTP Server IP: Enter the IP address of your TFTP server. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 74: Ping Test
This chapter provides the procedure to ping a node on your network from the switch. This procedure is useful in determining whether an active link exists between the switch and another network device. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 75: Trace Route
Note: You may want to save the settings to flash before reboot the switch under Save Settings to Flash (menu) > Save Settings to Flash (button). If you have not saved your current configuration settings to flash first, the configuration changes will be lost after a reboot. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 76 Hardware Method: Using a paper clip, on the front panel of the switch, push and hold the Reset button more than 6 seconds and release. Located on the front panel of your switch, see “Product Hardware Features” on page 2. Use © Copyright 2023 TRENDnet. All Rights Reserved.
Page 77: Command Line Interface Reference
3. Select the appropriate COM port used for connecting to the switch console. 4. Use the following settings for the connection. • Data Rate: 115200 bps Data Bit: 8 bits • • Parity: None Stop Bits: 1 • • Flow Control: None © Copyright 2023 TRENDnet. All Rights Reserved.
Page 78 SNTP <interfacetype><interfacei configuration mode. d> Config- <Switch Name> (config-vlan)# The Global VLAN is used to enter configuration mode the Interface command vlan vlan-id configuration is used to enter the mode. Config-VLAN mode. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 79 MAC ACL Extended <Switch The MAC ACL Extended Access List Name> Access List Configuration configuration mode command mac (config- access-list extended <name> ext-macl)# used to enter the MAC ACL Extended Access List configuration mode. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 80 Command Objective This command displays a brief description for the given command. Syntax help [ command ] Mode All Modes 4.1.2 clear screen Command Objective This command clears all the contents from the screen. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 81 TL2-F7120 TRENDnet User’s Guide Syntax clear screen Mode All Modes 4.1.1 Command Objective Exit from Configure mode. Syntax Mode All Modes 4.1.2 logout © Copyright 2023 TRENDnet. All Rights Reserved.
Page 82 Prompt in case of console session. In case of a telnet session, this command terminates the session. Syntax logout Mode Privileged EXEC Mode 4.1.3 show privilege Command Objective Show current privilege level. Syntax show privilege © Copyright 2023 TRENDnet. All Rights Reserved.
Page 83 TL2-F7120 TRENDnet User’s Guide Mode Privileged EXEC Mode show cli Command Objective This command displays TTY line information such as EXEC timeout. Syntax show cli Mode Privileged EXEC Mode 4.1.4 exit © Copyright 2023 TRENDnet. All Rights Reserved.
Page 84 All Modes configure terminal Command Objective This command enters to Global Configuration Mode which allows the user to execute all the commands that supports global configuration mode. Syntax configure terminal Mode Privileged EXEC Mode © Copyright 2023 TRENDnet. All Rights Reserved.
Page 85 This command lists all the default and newly created users, along with their permissible mode. Syntax listuser Mode Privileged EXEC Mode 4.1.7 show users Command Objective This command displays the information about the current user. © Copyright 2023 TRENDnet. All Rights Reserved.
Page 88 The no form of the command deletes a user and disables the enable password for that user. Syntax username <user-name> [password <passwd>] [privilege <1-15>] no username < user-name > © Copyright 2023 TRENDnet. All Rights Reserved.
Page 89 Command Objective This command configures minimum password length. If the given password has less than the configured password length, it will not be allowed This value ranges between 8 and 20. Copyright 2023 TRENDnet. All Rights Reserved.
Page 90 This command identifies a specific line for configuration and enters the line configuration mode and allows the user to execute all the commands that supports line configuration mode. Syntax line cli Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 91 This command sets a time (in seconds) for EXEC line disconnection. This value ranges between 1 and 10000 seconds. The no form of this command resets the EXEC timeout to its default value. Syntax exec-timeout <integer (1-18000)> no exec-timeout Mode Line Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 92 - Configures the IP address of the node to be pinged. • ipAddress - Configures the source IP address of the node to be Description pinged. • hostname - Configures the name of the host. Copyright 2023 TRENDnet. All Rights Reserved.
Page 93 Configures the size of the data portion of the PING PDU. Mode Privileged EXEC Mode traceroute Command Objective This command traces route to the destination. Syntax traceroute {<ip_addr>|<string> | ipv6 <ip6_addr>} [max-ttl <short (2- 255)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 94 This command clears all the current interface counters from the interface unless the optional arguments type and number are specified to clear only a specific interface type (serial, Ethernet, Token Ring, and so on). Copyright 2023 TRENDnet. All Rights Reserved.
Page 95 This value is a combination of slot number and port number separated by a slash. For Example: 0/1 represents that the slot number is 0 and port number is 1. Mode Privileged EXEC Mode 4.1.14 jumbo-frame Copyright 2023 TRENDnet. All Rights Reserved.
Page 96 This value is shown to the higher interface sub-layer and should not include size of the encapsulation or header added by the interface. Syntax jumbo-frame <frame-size(1522-9216)> Mode Global Configuration Mode 4.1.15 interface range Copyright 2023 TRENDnet. All Rights Reserved.
Page 97 • vlan <vlan-id(1-4094)> - <vlan-id(2-4094)> - Selects the range of the specified VLAN ID. This is a unique value that represents the specific VLAN created and activated. This value ranges between 1 and 4094. Copyright 2023 TRENDnet. All Rights Reserved.
Page 98 Command Objective This command enters the configuration mode. Configuration from memory or network is not supported, when entered into the configuration mode using this command. Syntax configure Mode Privileged EXEC Mode 4.1.2 mac-address-table static unicast Copyright 2023 TRENDnet. All Rights Reserved.
Page 99 The no form of the command deletes a configured static Unicast MAC address from the forwarding database. Syntax mac-address-table static unicast <aa:aa:aa:aa:aa:aa> vlan <vlan-id > interface ([<interface-type> <0/a-b, 0/c, ...>] [<interface-type> <0/a-b, 0/c, ...>] [port- channel <a,b,c-d>]) no mac-address-table static unicast <aa:aa:aa:aa:aa:aa> vlan <vlan-id > Copyright 2023 TRENDnet. All Rights Reserved.
Page 100 This is a unique value that represents the specific interface. This value is a combination of slot number and port number separated by a slash. Port- channel ID is provided, for interface type port-channel. Use Copyright 2023 TRENDnet. All Rights Reserved.
Page 102 This reduces the possibility of flooding. The no form of the command resets the maximum age of an entry in the MAC address table to its default value. Copyright 2023 TRENDnet. All Rights Reserved.
Page 103 <10-630 seconds> no mac-address-table aging-time Mode Global Configuration Mode/ Switch Configuration Mode 4.1.17 set switch-name Command Objective This command sets the name of the switch. Syntax set switch-name <switchname> Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 104 This command enables/disables HTTP in the switch. Syntax set ip http {enable | disable} • Parameter Description enable - Enables HTTP in the switch. • disable - Disables HTTP in the switch. Mode Global Configuration Mode 4.1.19 ip telnet service Copyright 2023 TRENDnet. All Rights Reserved.
Page 105 This command copies a file from a source remote site /flash to a destination remote site/flash. The entire copying process takes several minutes and differs from protocol to protocol and from network to network. Syntax copy startup-config { tftp://ip-address/filename } Copyright 2023 TRENDnet. All Rights Reserved.
Page 106 Filenames and directory names are case sensitive Mode Privileged EXEC Mode 4.1.21 copy Command Objective This command copies the configuration from a remote site to flash. Syntax copy { tftp://ip-address/filename startup-config} Copyright 2023 TRENDnet. All Rights Reserved.
Page 107 This command copies variables from the running configuration to the startup configuration file in NVRAM, where the running-config is the current configuration in the router and the startup config is the configuration that is loaded when the switch boots up. Copyright 2023 TRENDnet. All Rights Reserved.
Page 108 TL2-F7120 TRENDnet User’s Guide Syntax save Mode Privileged EXEC Mode 4.1.23 copy logs Command Objective This command writes the system logs to a remote site. Syntax copy logs { tftp://ip-address/filename } Copyright 2023 TRENDnet. All Rights Reserved.
Page 109 Filenames and directory names are case sensitive Mode Privileged EXEC Mode 4.1.24 clock set Command Objective This command manages the system clock. Syntax clock set hh:mm:ss <day (1-31)> {january|february|march|april|may|june|july|august|september|oct ober|november|december} <year (2000 - 2035)> Copyright 2023 TRENDnet. All Rights Reserved.
Page 110 - Sets the month as November ■ december - Sets the month as December ■ <year (2000 - 2035)> - Sets the year. It ranges between 2000 and 2035 Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 111 TL2-F7120 TRENDnet User’s Guide 4.1.25 show clock Command Objective This command displays the system date and time. Syntax show clock Mode Privileged EXEC Mode 4.1.26 show jumbo-frame Copyright 2023 TRENDnet. All Rights Reserved.
Page 112 Syntax show jumbo-frame Mode Privileged EXEC Mode show system information Command Objective This command displays system information. Syntax show system information Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 113 TL2-F7120 TRENDnet User’s Guide 4.1.28 reboot Command Objective This command restarts the switch. Syntax reboot Mode Privileged EXEC Mode 4.1.29 restore-defaults Command Objective This command restore default configuration. Syntax restore-defaults Copyright 2023 TRENDnet. All Rights Reserved.
Page 114 TL2-F7120 TRENDnet User’s Guide Mode Privileged EXEC Mode 4.1.1 show telnet server Command Objective This command displays the telnet server status. Syntax show telnet server Mode Privileged EXEC Mode 4.1.2 show http server status Copyright 2023 TRENDnet. All Rights Reserved.
Page 115 Privileged EXEC Mode 4.1.30 port speed - duplex Command Objective This command configures the speed and duplex operation. Syntax speed { 10 | 100 | 1000 | 10000 } duplex { full | half } Copyright 2023 TRENDnet. All Rights Reserved.
Page 116 - Port is in full-duplex mode, that is data simultaneously communicates in both directions. • half - Port is in half-duplex mode, that is data can communicate in both directions, but only in one direction at a time. Mode Interface Configuration 4.1.31 negotiation Copyright 2023 TRENDnet. All Rights Reserved.
Page 117 The port in which auto-negotiation is enabled, negotiates with the other end for port properties like speed, duplexity and so one. The normal port uses the port property values configured by the administrator. Syntax negotiation no negotiation Mode Interface Configuration port-isolation Copyright 2023 TRENDnet. All Rights Reserved.
Page 118 - Enables the Port Isolation rule in this ingress interface. • disabled - Disables the Port Isolation rule in this ingress interface. Mode Interface Configuration 4.1.33 show port-isolation status Command Objective This command displays the Port Isolation table. Syntax show port-isolation status Copyright 2023 TRENDnet. All Rights Reserved.
Page 119 This command sets the system time zone with respect to UTC. The no form of command resets the system time zone to GMT. Syntax clock utc-offset <UTC-offset value as (+HH:MM /-HH:MM)(+00:00 to +14:00)/ (-00:00 to -12:00)> Eg: +05:30 Copyright 2023 TRENDnet. All Rights Reserved.
Page 120 UTC- offset value as - Sets the UTC offset value in hours. +00:00 to +14:00 -00:00 to -12:00 Mode Global Configuration Mode 4.1.35 show clock properties Command Objective This command displays the PTP clock properties. Copyright 2023 TRENDnet. All Rights Reserved.
Page 121 This command allows to configure interface such as VLAN. Syntax interface {vlan < vlan-id > [switch <string(32)>] | port-channel <integer (1-8)> | <iftype> <ifnum>} no interface {vlan < vlan-id > [switch <string(32)>] | port-channel <integer (1-8)> | <iftype> <ifnum>} Copyright 2023 TRENDnet. All Rights Reserved.
Page 122 Industry Standard CLI syntax. • port-channel<port-channel-id (1-8)>- Configures the port to be used by the host to configure the router. This value ranges between 1 and 8. The port channel identifier can be created or Copyright 2023 TRENDnet. All Rights Reserved.
Page 123 1 Gigabit per second. ■ port-channel – Logical interface that represents an aggregator which contains several ports aggregated together. Mode Global Configuration Mode 4.1.37 ip address Command Objective This command sets the IP address for an interface. Copyright 2023 TRENDnet. All Rights Reserved.
Page 125 Syntax ip address dhcp ip address bootp no ip address • Parameter dhcp – Get IP by using DHCP protocol. • Description botp – Get IP by using BOOTP protocol. Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 126 TL2-F7120 TRENDnet User’s Guide 4.1.1 shutdown Command Objective Set the AdminStatus of Interface down/up. Syntax shutdown no shutdown Description Set the AdminStatus of Interface down/up. Mode Interface Configuration Mode 4.1.2 description Copyright 2023 TRENDnet. All Rights Reserved.
Page 127 Command Objective Descriptions about the interface. Syntax description <description of this interface> no description Description Descriptions about the interface. Or Cancel the descriptions about the interface. Mode Interface Configuration Mode 4.1.39 show interface port-security Copyright 2023 TRENDnet. All Rights Reserved.
Page 128 The interface can be: Description ■ gigabitethernet – A version of LAN standard architecture that supports data transfer upto 1 Gigabit per second. Mode Privileged EXEC Mode 4.1.40 show interface cable-diag Copyright 2023 TRENDnet. All Rights Reserved.
Page 129 Description OPEN–This pair is left open. SHORT–This pair has been shorted between two lines of its own. Unknown–The last diagnosis do not obtain the cable’ status, please try it again. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 130 - Displays the IP interface configuration for the specified interface identifier. This is a unique value that represents the specific interface. This value is a combination of slot number and port number separated by a slash. For Example: 0/1 represents that the slot number is 0 and port number is 1. Copyright 2023 TRENDnet. All Rights Reserved.
Page 131 TL2-F7120 TRENDnet User’s Guide Mode Privileged EXEC Mode 4.1.42 show flow-control Command Objective This command displays the flow-control information. Syntax show flow-control [ interface <interface-type> <interface-id>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 132 This value is a combination of slot number and port number separated by a slash. For Example: 0/1 represents that the slot number is 0 and port number is 1. Mode Privileged EXEC Mode 4.1.43 snmp trap link-status Copyright 2023 TRENDnet. All Rights Reserved.
Page 133 The linkDown trap denotes that the communication link failed and is not ready for traffic flow. Syntax snmp trap link-status no snmp trap link-status Mode Interface Configuration Mode 4.1.44 flowcontrol Copyright 2023 TRENDnet. All Rights Reserved.
Page 134 - Turns-off the attached devices (when used with receive) or the local ports (when used with send) ability to send flow-control packets to an interface or to a remote device respectively. Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 135 This command configures the number of learning address on certain interface port. Syntax port-security <limit-size(1-256)> no port-security • Parameter < limit-size(1-256)>-Range is 1 to 256. Description Mode Interface Configuration Mode 4.1.46 show security-suite Command Objective Displays Dos information. Copyright 2023 TRENDnet. All Rights Reserved.
Page 136 The no form of the command deletes the IP access-list. Syntax ip access-list extended <string(31)> no ip access-list extended <string(31)> • Parameter <string(31)> –Configures the extended access-list name. Description Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 137 The no form of the command deletes the mac access-list. Syntax mac access-list extended <string(31)> no mac access-list extended <string(31)> • Parameter <string(31)> –Configures the access-list name. Description Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 138 The no form of the command deletes the ipv6 access-list. Syntax ipv6 access-list extended <string(31)> no ipv6 access-list extended <string(31)> • Parameter <string(31)> –Configures the access-list name. Description Mode Global Configuration Mode 4.1.50 permit- ip/ospf/pim/protocol type Copyright 2023 TRENDnet. All Rights Reserved.
Page 139 Syntax permit { ip | ospf | pim | <short (1-255)>} { any| host <src-ip- address>|<src-ip-address> <mask>} { any|host <dest-ip- address>|<dest-ip-address> <mask> } ace-priority <integer (1- 2147483647)> [ dscp <short (0-63)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 140 • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV4 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 141 Syntax deny { ip | ospf | pim | <short (1-255)>} { any| host <src-ip- address>|<src-ip-address> <mask> } { any|host <dest-ip- address>|<dest-ip-address> <mask> } ace-priority <integer (1- 2147483647)> [ dscp <short (0-63)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 142 • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV4 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 143 <short (1-65535)>] { any|host <dest-ip-address>|<dest-ip-address> <mask> } [eq <short (1-65535)>] ace-priority <integer (1-2147483647)> [{ack | non_ack}] [{rst | non_rst}] [{psh | non_psh}] [{urg | non_urg}] [{syn | non_syn}] [{fin | non_fin}] [dscp <short (0-63)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 144 • eq <short (1-65535)> - Port Number. • any|host <dest-ip-address>|<dest-ip-address> <mask> Destination IP address can be ■ ‘any’ or ■ the dotted decimal address or Copyright 2023 TRENDnet. All Rights Reserved.
Page 145 | non_fin - TCP FIN bit to be checked against the packet. • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV4 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 146 <mask> } [eq <short (1-65535)>] ace-priority <integer (1-2147483647)> [{ack | non_ack}] [{rst | non_rst}] [{psh | non_psh}] [{urg | non_urg}] [{syn | non_syn}] [{fin | non_fin}] [dscp <short (0-63)>] • Parameter - Transport Control Protocol. Copyright 2023 TRENDnet. All Rights Reserved.
Page 147 TCP SYN bit to be checked against the packet. • fin | non_fin - TCP FIN bit to be checked against the packet. • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Copyright 2023 TRENDnet. All Rights Reserved.
Page 148 This command specifies the UDP packets to be forwarded based on the associated parameters. Syntax permit udp { any| host <src-ip-address>|<src-ip-address> <mask> } [eq <short (1-65535)> ] { any|host <dest-ip-address>|<dest-ip-address> <mask> } [ eq <short (1-65535)> ] ace-priority <integer (1- 2147483647)> [ dscp <short (0-63)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 149 • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV4 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 150 This command specifies the UDP packets to be rejected based on the associated parameters. Syntax deny udp { any| host <src-ip-address>|<src-ip-address> <mask> } [eq <short (1-65535)> ] { any|host <dest-ip-address>|<dest-ip-address> <mask> } [ eq <short (1-65535)> ] ace-priority <integer (1- 2147483647)> [ dscp <short (0-63)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 151 • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV4 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 152 This command specifies the ICMP packets to be forwarded based on the IP address and the associated parameters. Syntax permit icmp { any| host <src-ip-address>|<src-ip-address> <mask>} { any|host <dest-ip-address>|<dest-ip-address> <mask> } [type <short (0- 255)>] [code <short (0-255)>] ace-priority <integer (1-2147483647)> [dscp <integer (0-63)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 153 ‘any’ or ■ the dotted decimal address or ■ the IP Address of the network or the host that the packet is destined for and the network mask to use with the destination address Copyright 2023 TRENDnet. All Rights Reserved.
Page 154 Mode IPV4 ACL Extended Access List Configuration Mode 4.1.57 deny icmp Command Objective This command specifies the ICMP packets to be rejected based on the IP address and associated parameters. Copyright 2023 TRENDnet. All Rights Reserved.
Page 155 ■ the IP Address of the network or the host that the packet is from and the network mask to use with the source address. • any|host <dest-ip-address>|<dest-ip-address> <mask> Destination IP address can be Copyright 2023 TRENDnet. All Rights Reserved.
Page 156 • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV4 ACL Extended Access List Configuration Mode no ace-priority Copyright 2023 TRENDnet. All Rights Reserved.
Page 157 Description more than one filter rules. Mode IPV4 ACL Extended Access List Configuration Mode 4.1.59 permit ipv6 Command Objective This command specifies IPv6 packets to be forwarded based on protocol and associated parameters. Copyright 2023 TRENDnet. All Rights Reserved.
Page 158 • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV6 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 159 - The priority of the filter is used to decide which filter rule is applicable when the packet matches with more than one filter rules. • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Copyright 2023 TRENDnet. All Rights Reserved.
Page 160 65535)>] {any | host <ip6_addr> <short(0-128)>} [eq <short (1- 65535)>] {ace-priority <integer (1-2147483647)>} [{ack | non_ack}] [{rst | non_rst}] [{psh | non_psh}] [{urg | non_urg}] [{syn | non_syn}] [{fin | non_fin}] [dscp <short (0-63)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 161 | non_fin - TCP FIN bit to be checked against the packet. • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV6 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 162 65535)>] {any | host <ip6_addr> <short(0-128)>} [eq <short (1- 65535)>] {ace-priority <integer (1-2147483647)>} [{ack | non_ack}] [{rst | non_rst}] [{psh | non_psh}] [{urg | non_urg}] [{syn | non_syn}] [{fin | non_fin}] [dscp <short (0-63)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 163 | non_fin - TCP FIN bit to be checked against the packet. • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV6 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 164 This command specifies the IPv6 TCP packets to be forwarded based on the associated parameters. • Syntax permit udp {any | host <ip6_addr> <short(0-128)>} [eq <short (1- 65535)>] {any | host <ip6_addr> <short(0-128)>} [ eq <short (1- 65535)> ] ace-priority <integer (1-2147483647)> [dscp <short (0- 63)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 165 • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV6 ACL Extended Access List Configuration Mode 4.1.64 deny udp Copyright 2023 TRENDnet. All Rights Reserved.
Page 166 • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV6 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 167 This command specifies the IPv6 TCP packets to be forwarded based on the associated parameters. • Syntax permit icmpv6 {any | host <ip6_addr> <integer(0-128)>} {any | host <ip6_addr> <integer(0-128)>} ace-priority <integer (1- 2147483647)> [type <short(0-255)>] [code <short(0-255)>] [dscp <short(0-63)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 168 <short (0-255)> message type • code <short (0-255)> - message code • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Mode IPV6 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 169 • type <short (0-255)> message type • code <short (0-255)> - message code • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. Copyright 2023 TRENDnet. All Rights Reserved.
Page 170 - The priority of the filter is used to decide which filter rule is applicable when the packet matches with Description more than one filter rules. Mode IPV6 ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 171 IP traffic to be forwarded if the conditions are matched. • Syntax permit { any | <src-mac-address > } { any | host <mac_addr> } {ace-priority <integer (1-2147483647)>} [ ethertype <integer (1- 65535)> ] [ vlan <integer (1-4094)>] [ vlan-priority <short (0-7)> ] Copyright 2023 TRENDnet. All Rights Reserved.
Page 172 <integer (1-4094)> - VLAN value to match against incoming packets. • vlan-priority <short (0-7)> - VLAN priority value to match against incoming packets. Mode MAC ACL Extended Access List Configuration Mode 4.1.69 deny mac Copyright 2023 TRENDnet. All Rights Reserved.
Page 173 <integer (1-65535)> Specifies the non-IP protocol type to be filtered. • vlan <integer (1-4094)> - VLAN value to match against incoming packets. • vlan-priority <short (0-7)> - VLAN priority value to match against incoming packets. Copyright 2023 TRENDnet. All Rights Reserved.
Page 174 - The priority of the filter is used to decide which filter rule is applicable when the packet matches with Description more than one filter rules. Mode MAC ACL Extended Access List Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 175 The no form of this command removes all access groups or the specified access group from the interface. Syntax ip access-group <string (31)> in no ip access-group [<string(31)>] in • Parameter <string(31)> - IP access control list name. Description Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 176 The no form of this command removes all access groups or the specified access group from the interface. Syntax Ipv6 access-group <string (31)> in no ipv6 access-group [<string(31)>] in • Parameter <string(31)> - IPv6 access control list name. Description Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 177 The no form of this command can be used to remove the MAC ACLs from the interface. Syntax mac access-group <string (31)> in no mac access-group [<string(31)>] in • Parameter <string(31)> - MAC access control list name. Description Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 178 Parameter - IP Access List • – MAC Access List Description • ipv6 – Ipv6 Access List • <string(31)> - Name of access list Mode Privilege EXEC Mode . DHCP SERVER service dhcp-server relay Copyright 2023 TRENDnet. All Rights Reserved.
Page 179 A DHCP relay agent is any host or IP router that forwards DHCP packets between clients and servers. ✏ The DHCP server relay can be config in the switch. Syntax service dhcp-relaydh no service dhcp-server Mode Global Configuration Mode . DNS Copyright 2023 TRENDnet. All Rights Reserved.
Page 180 <ucast_addr> no domain name-server ipv4 <ucast_addr> • Parameter ipv4 <ucast_addr> - Sets the IP address for the domain name server in IPv4 address format. Description Mode Global Configuration Mode 4.1.77 show ip dns name-server Copyright 2023 TRENDnet. All Rights Reserved.
Page 181 Mode Privilege EXEC Mode . EEE 4.1.91 Command Objective This command enables/disables Energy Efficient Ethernet on the specified port . The no form of the command disable Energy Efficient Ethernet on the specified port. Copyright 2023 TRENDnet. All Rights Reserved.
Page 182 TL2-F7120 TRENDnet User’s Guide Syntax no eee Mode Interface Configuration Mode 4.1.92 show eee Command Objective This command displays the Energy Efficient Ethernet information of each port. Syntax show eee Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 183 The no form of the command starts and enables snooping in the switch. ✏ Snooping cannot be started in the switch, if the base bridge mode is configured as transparent bridging. Syntax shutdown snooping no shutdown snooping Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 184 The PIM queries the IGS module to obtain the Portlist. Description • - Configures the multicast forwarding mode as MAC Address based. The PIM queries the VLAN to obtain the Portlist. Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 185 IGMP snooping is enabled globally, it is enabled in all the existing VLAN interfaces. The no form of the command disables IGMP snooping in the switch/a specific VLAN. When IGMP snooping is disabled globally, it is disabled in all the existing VLAN interfaces. Copyright 2023 TRENDnet. All Rights Reserved.
Page 186 • Parameter <vlan –id> - VLAN ID is a unique value that represents the specific VLAN. This value ranges between 1 and 4094. Description Mode Global Configuration Mode / Config-VLAN Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 187 IGMP Snooping is operationally enabled IGMP Snooping Enhanced mode is disabled IGMP Snooping Sparse mode is disabled Transmit Query on Topology Change globally disabled Multicast forwarding mode is MAC based Proxy globally disabled Proxy reporting globally disabled Copyright 2023 TRENDnet. All Rights Reserved.
Page 188 Snooping switch is configured as Non-Querier Snooping switch is acting as Non-Querier Startup Query Count is 2 Startup Query Interval is 15 seconds Query interval is 125 seconds Other Querier Present Interval is 256 seconds Copyright 2023 TRENDnet. All Rights Reserved.
Page 189 60 and 600 seconds. This command is a standardized implementation of the existing command; ip igmp snooping mrouter-time-out. It operates similar to the existing command. Syntax ip igmp querier-timeout <(60 - 600) seconds> Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 190 The no form of the command disables fast leave processing for a specific VLAN. This command is a standardized implementation of the existing command; ip igmp snooping fast-leave. It operates similar to the existing command. Copyright 2023 TRENDnet. All Rights Reserved.
Page 191 VLAN, will be applied only when IGMP snooping is enabled in the VLAN. Syntax ip igmp snooping vlan <vlanid(1-4094)> immediate-leave no ip igmp snooping vlan <vlanid(1-4094)> immediate-leave Mode Global Configuration Mode 4.1.91 ip igmp snooping report-suppression interval Copyright 2023 TRENDnet. All Rights Reserved.
Page 192 ✏ The ip igmp snooping report-suppression-interval is used only when the proxy and proxy-reporting are disabled. Syntax ip igmp snooping report-suppression-interval <(1 – 25) seconds> no ip igmp snooping report-suppression-interval Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 194 The no form of the commands sets the group specific query interval time to default value. Syntax ip igmp snooping group-query-interval <2-5) seconds> no ip igmp snooping group-query-interval Mode Global Configuration Mode 4.1.91 ip igmp snooping querier Copyright 2023 TRENDnet. All Rights Reserved.
Page 195 The no form of the command configures the IGMP snooping switch as non- querier for a specific VLAN. Syntax ip igmp snooping querier no ip igmp snooping querier Mode Config-VLAN Mode 4.1.92 ip igmp snooping query-interval Copyright 2023 TRENDnet. All Rights Reserved.
Page 196 The no form of the command sets the IGMP querier interval to default value. ✏ The switch must be configured as a querier for this configuration to be imposed. Syntax ip igmp snooping query-interval <(60 - 600) seconds> no ip igmp snooping query-interval Mode Config-VLAN Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 197 - Displays the specified context. This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 198 - Displays the specified context. This value represents unique name of the switch context. This value is a string Description whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 199 This command adds a static route. The Route defines the IP address or interface through which the destination can be reached. Syntax ip route <ip_addr> <ip_mask> <ucast_addr> [<short (1-254)>] no ip route <ip_addr> <ip_mask> <ucast_addr> Copyright 2023 TRENDnet. All Rights Reserved.
Page 200 - Defines the IP address or IP alias of the next hop that can be used to reach that network. Mode Global Configuration Mode 4.1.101 show ip route Command Objective This command displays the IP routing table. Copyright 2023 TRENDnet. All Rights Reserved.
Page 201 Displays the Directly Connected Network Routes. • static- Displays the Static Routes in the table. • summary- Displays the Summary of all routes. • details-Displays the details of all routes. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 202 - The MAC address corresponding to the IP address above. • <vlan –id>- VLAN ID is a unique value that represents the specific VLAN. This value ranges between 1 and 4094. Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 203 The timeout values can be assigned to dynamic arp entries only. All static arp entries remain unaltered by the timeout value. This value ranges between 30 and 86400 seconds. Syntax arp timeout <integer (30-86400)> no arp timeout Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 204 Command Objective This command displays IP ARP table. Syntax show ip arp [ { Vlan <vlan_id> | <iftype> <ifnum> | <ipiftype> <ifnum> | <ucast_addr> | <ucast_mac> | summary | information | statistics } ] Copyright 2023 TRENDnet. All Rights Reserved.
Page 205 - Displays the MAC Address of ARP Entry. • summary - Displays IP ARP Table summary. • information- Displays the ARP Configuration information regarding maximum retries and ARP cache timeout. Mode Privileged EXEC Mode . IPV6 Copyright 2023 TRENDnet. All Rights Reserved.
Page 206 Command Objective This command enables the DHCPv6 client functionality over the interface and requests for configuration information from the client. Syntax ipv6 address dhcp no ipv6 address dhcp Mode Interface Configuration Mode 4.1.105 ipv6 unicast-routing Copyright 2023 TRENDnet. All Rights Reserved.
Page 207 Syntax ipv6 unicast-routing no ipv6 unicast-routing Mode Interface Configuration Mode 4.1.106 ipv6 enable Command Objective This command enables IPv6 processing on an interface that has not been configured with an explicit IPv6 address. Copyright 2023 TRENDnet. All Rights Reserved.
Page 208 Interface Configuration Mode 4.1.107 ipv6 address - prefix and prefix length Command Objective This command configures IPv6 address on the interface. Syntax ipv6 address <prefix> <prefix Len> [unicast] no ipv6 address <prefix> <prefix Len> [unicast] Copyright 2023 TRENDnet. All Rights Reserved.
Page 209 These bits are common among all hosts within a network. This value ranges between 0 and 128. • unicast- Configures the address type of the prefix as Unicast. Mode Interface Configuration Mode 4.1.108 ipv6 address - link local Copyright 2023 TRENDnet. All Rights Reserved.
Page 210 <prefix> link-local • Parameter <prefix>-Configures the IPv6 prefix for the interface. Description Mode Interface Configuration Mode 4.1.109 show ipv6 interface Command Objective This command displays the IPv6 interfaces. Syntax show ipv6 interface [{vlan <vlan-id> [prefix]}] Copyright 2023 TRENDnet. All Rights Reserved.
Page 211 VLAN. This value ranges between 1 and 4094. Description Mode Privileged EXEC Mode 4.1.110 show ipv6 route Command Objective This command displays the IPv6 Routes. Syntax show ipv6 route Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 212 TL2-F7120 TRENDnet User’s Guide 4.1.111 show ipv6 route - summary Command Objective This command displays the summary of IPv6 Routes. Syntax show ipv6 route summary Mode Privileged EXEC Mode 4.1.112 show ipv6 neighbors Copyright 2023 TRENDnet. All Rights Reserved.
Page 213 Command Objective This command sends IPv6 echo messages along with the total number of packets to the destination. Syntax ping ipv6 <prefix%interface> [repeat <count>] [size <value>] [source {vlan <vlan-id> | <source_prefix>}] [timeout <value (1-100)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 214 Configures source prefix of the ping message. • timeout <value (1-100)>- Configures the time in seconds after which this entity times out waiting for a particular ping response. The value ranges between 1 to 100. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 215 LACP decides the standby and active links in the LA. The no form of the command resets the LACP priority to its default value. Syntax lacp system-priority <0-65535> no lacp system-priority Mode Global Configuration Mode 4.1.114 port-channel load-balance Copyright 2023 TRENDnet. All Rights Reserved.
Page 216 This command configures the load balancing policy for all port channels created in the switch. The policy sets the rule for distributing the Ethernet traffic among the aggregated links to establish load balancing. Syntax port-channel load-balance ([src-mac][dest-mac][src-dest-mac][src- ip][dest-ip][src-dest-ip][dest-l4-port][src-l4-port]) Copyright 2023 TRENDnet. All Rights Reserved.
Page 217 IP address. The bits of the source and destination IP address in the packet are used to select the port in which the traffic should flow. • dest-l4-port - Distributes the load based on the destination Layer Copyright 2023 TRENDnet. All Rights Reserved.
Page 218 - Distributes the load based on the source Layer 4 port. The bits of the source Layer 4 port in the packet are used to select the port in which the traffic should flow. Copyright 2023 TRENDnet. All Rights Reserved.
Page 219 The no form of the command deletes the aggregation of the port from all port channels. Syntax channel-group <channel-group-number(1-8)> Mode { on | active | passive } no channel-group Copyright 2023 TRENDnet. All Rights Reserved.
Page 220 This command configures the LACP timeout period within which LACPDUs should be received on a port to avoid timing out of the aggregated link. The no form of the command sets the LACP timeout period to its default value. Copyright 2023 TRENDnet. All Rights Reserved.
Page 221 PDU is sent every 30 seconds. • short - Configures the LACP timeout period as 3 seconds. The LACP PDU is sent every second. Mode Interface Configuration Mode (Physical Interface Mode) 4.1.117 show etherchannel Copyright 2023 TRENDnet. All Rights Reserved.
Page 222 This information contains admin and oper status of port- channel module, and status of protocol operate Mode for each group. Syntax show etherchannel [[channel-group-number] { detail | load-balance | port | port-channel | summary | protocol}] Copyright 2023 TRENDnet. All Rights Reserved.
Page 223 The port channel details contain port channel ID, number of member ports, ID of hot standby port, port state, status of protocol operate Mode, aggregator MAC and default port ID. Copyright 2023 TRENDnet. All Rights Reserved.
Page 224 TL2-F7120 TRENDnet User’s Guide • summary - Displays the admin and oper status of port channel module, number of channel groups used, number of aggregators, Copyright 2023 TRENDnet. All Rights Reserved.
Page 225 - Displays the status of protocol operate Mode for each port-channel group. Mode Privileged EXEC Mode . LBD 4.1.118 Command Objective This command enables/disables Loopback Detection. Syntax lbd { enable | disable } Mode Global Configuration Mode 4.1.119 show lbd state Copyright 2023 TRENDnet. All Rights Reserved.
Page 226 This command displays the Loopback Detection information. Syntax show lbd state Mode Privileged EXEC Mode 4.1.120 show lbd state Command Objective This command displays the Loopback Detection information of each port. Syntax show lbd port state Copyright 2023 TRENDnet. All Rights Reserved.
Page 227 • Parameter enable - Transmits/receives the LLDP packets between LLDP module and the server. Description • disable - Does not transmit/receive the LLDP packets between LLDP module and the server. Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 228 This command sets the holdtime-multiplier value, which is the amount of time, the server should hold the LLDP. The value ranges between 2 and 10 seconds. The no form of the command sets the multiplier to the default value. Copyright 2023 TRENDnet. All Rights Reserved.
Page 229 For Example, if the value of LLDP transmission interval is 30, and the value of the LLDP hold multiplier is 4, then the value 120 is encoded in the TTL field in the LLDP header. Syntax lldp holdtime-multiplier <value(2-10)> no lldp holdtime-multiplier Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 230 The value ranges between 1 and 10 seconds. The no form of the command sets the reinitialization delay time to the default value. Syntax lldp reinitialization-delay <seconds(1-10)> no lldp reinitialization-delay Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 231 The no form of the command sets the transmit delay to the default value. ✏ TxDelay should be less than or equal to (0.25 * Message Tx Interval) Syntax lldp tx-delay <seconds(1-8192)> no lldp tx-delay Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 232 LLDP frames to the LLDP module.The value ranges between 5 and 32768 seconds. The no form of the command sets the transmission interval to the default value. Syntax lldp transmit-interval <seconds(5-32768)> no lldp transmit-interval Mode Global Configuration Mode show lldp Copyright 2023 TRENDnet. All Rights Reserved.
Page 233 This command displays LLDP global configuration details to initialize on an interface. Syntax show lldp Mode Privileged EXEC Mode 4.1.122 show lldp interface Command Objective This command displays the information about interfaces where LLDP is enabled. Syntax show lldp interface [<interface-type> <interface-id>] [mac-address <mac_addr>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 234 1. Only port-channel ID is provided, for interface type port-channel. For Example: 1 represents port-channel ID. • mac-address <mac_addr> - Displays information about neighbors for the specidfied destination MAC address of the LLDP agent. Mode Privileged EXEC Mode 4.1.123 show lldp neighbors Copyright 2023 TRENDnet. All Rights Reserved.
Page 235 TL2-F7120 TRENDnet User’s Guide Command Objective This command displays information about neighbors on an interface or all interfaces. Syntax show lldp neighbors [chassis-id <string(255)> port-id <string(255)>] [<interface-type> <interface-id> [mac- address<mac_addr>] ][detail] Copyright 2023 TRENDnet. All Rights Reserved.
Page 236 <mac_addr> - Displays information about neighbors for the specidfied destination MAC address of the LLDP agent. • detail - Displays the information obtained from all the received TLVs . Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 237 This command displays the current switch information that will be used to populate outbound LLDP advertisements for a specific interface or all interfaces. Syntax show lldp local {[<interface-type> <interface-id> [macaddress <mac_addr>] ] | [mgmt-addr]} Copyright 2023 TRENDnet. All Rights Reserved.
Page 238 MAC address of the LLDP agent. • mgmt-addr - All the management addresses configured in the system and Tx enabled ports. Mode Privileged EXEC Mode . MIRROR 4.1.125 monitor session - destination Copyright 2023 TRENDnet. All Rights Reserved.
Page 239 GigabitEthernet or or Port Channel. ■ <interface-id> – Interface identifier. This is a combination of slot number and port number. • allow-ingress- Allow Packets Ingress to Destination Port. Mode Global Configuration Mode 4.1.126 monitor session - source Copyright 2023 TRENDnet. All Rights Reserved.
Page 240 Syntax monitor session <session-id (1-3)> { source { interface <interface-type> <interface-id> [{ rx | tx | both }] }}} no monitor session <session-id (1-3)> { source { interface <interface- type> <interface-id> [{rx|tx|both}] Copyright 2023 TRENDnet. All Rights Reserved.
Page 241 - Mirrors received traffic • - Mirrors transmitted traffic • both - Specifies the traffic direction to monitor. If the traffic direction is not specified, both transmitted and received traffic is mirrored. Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 242 { session-range | session-id} • Parameter session-range - Specifies the list of session for which mirroring Description configuration should be removed • session-id - Specifies the index of the mirroring session. Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 243 - Displays the mirroring information for the specified list of mirroring session. • - Displays the mirroring information of all the sessions. • detail - Displays the detailed information regarding the session. Mode Global Configuration Mode 4.1.129 ipv6 mld snooping Copyright 2023 TRENDnet. All Rights Reserved.
Page 244 The MLDS can be enabled for a VLAN, only if the MLDS is started in the switch and the VLAN is activated. Syntax ipv6 mld snooping no ipv6 mld snooping Mode Global Configuration Mode/ Config-VLAN Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 245 The no form of this command sets the MLD snooping report- suppression interval to its default value. Syntax ipv6 mld snooping report-suppression-interval (1-25) seconds> no ipv6 mld snooping report-suppression-interval Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 246 Querier. The no form of this command sets the MLDS queriy interval to default value. ✏ The configuration can be done only for the VLANs that are activated in the switch. Copyright 2023 TRENDnet. All Rights Reserved.
Page 247 TL2-F7120 TRENDnet User’s Guide Syntax ipv6 mld snooping group-query-interval (2-5) seconds> no ipv6 mld snooping group-query-interval Mode Config-VLAN Mode 4.1.91 ipv6 mld snooping fast-leave Copyright 2023 TRENDnet. All Rights Reserved.
Page 248 The no form of the command disables fast leave processing for a specific VLAN. ✏ The configuration can be done only for the VLANs that are activated in the switch. Syntax ipv6 mld snooping fast-leave no ipv6 mld snooping fast-leave Mode Config-VLAN Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 249 VLAN. ✏ The configuration can be done only for the VLANs that are activated in the switch. Syntax ipv6 mld snooping querier <(60 - 600) seconds> no ipv6 mld snooping querier Copyright 2023 TRENDnet. All Rights Reserved.
Page 250 Querier. The no form of this command sets the MLDS queriy interval to default value. ✏ The configuration can be done only for the VLANs that are activated in the switch. Copyright 2023 TRENDnet. All Rights Reserved.
Page 251 The configuration can be done only for the VLANs that are activated in the switch. The specified interface can be set as router ports for the VLAN, only if the interfaces are configured as member ports for that VLAN. Copyright 2023 TRENDnet. All Rights Reserved.
Page 252 Port-channel ID is provided, for interface type port-channel. Use comma as a separator without space while configuring list of interfaces. Example: 0/1, 0/3 or 1, 3. Mode Config-VLAN Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 253 The ports to be configured as blocked router ports, must not be configured as static router ports. Syntax ipv6 mld snooping blocked-router <interface-type> <0/a-b, 0/c, ...> no ipv6 mld snooping blocked-router <interface-type> <0/a-b, 0/c, ...> Copyright 2023 TRENDnet. All Rights Reserved.
Page 254 Port- channel ID is provided, for interface type port-channel. Use comma as a separator without space while configuring list of interfaces. Example: 0/1, 0/3 or 1, 3. Mode Config-VLAN Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 255 This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.133 show ipv6 mld snooping globals Copyright 2023 TRENDnet. All Rights Reserved.
Page 256 This value represents unique name of the switch context. Description This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.134 show ipv6 mld snooping Copyright 2023 TRENDnet. All Rights Reserved.
Page 257 This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.135 show ipv6 mld snooping groups Copyright 2023 TRENDnet. All Rights Reserved.
Page 258 This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.136 show ipv6 mld snooping forwarding-database Copyright 2023 TRENDnet. All Rights Reserved.
Page 259 This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.137 show ipv6 mld snooping statistics Copyright 2023 TRENDnet. All Rights Reserved.
Page 260 - Displays the specified context. This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode PNAC Copyright 2023 TRENDnet. All Rights Reserved.
Page 261 It acts as mediator between the authentication server and the supplicant (client). If the client accesses the protected resources, it contacts the authenticator with EAPOL frames. Syntax dot1x system-auth-control no dot1x system-auth-control Mode Global Configuration Mode 4.1.139 shutdown dot1x Copyright 2023 TRENDnet. All Rights Reserved.
Page 262 The data transport and authentication are directly governed by the authentication server/server. When shutdown, all resources acquired by dot1x module are released to the system. Syntax shutdown dot1x no shutdown dot1x Mode Global Configuration Mode 4.1.140 dot1x clear statistics Copyright 2023 TRENDnet. All Rights Reserved.
Page 263 Description ■ gigabitethernet – A version of LAN standard architecture that supports data transfer up to 1 Gigabit per second. Mode Global Configuration Mode 4.1.141 security-suite Command Objective This command enables/disables DoS prevention. Copyright 2023 TRENDnet. All Rights Reserved.
Page 264 TL2-F7120 TRENDnet User’s Guide Syntax security-suite no security-suite Mode Global Configuration Mode 4.1.142 dot1x guest-vlan Command Objective This command configures Dot1x Guest VLAN ID. Syntax dot1x guest-vlan <short (1-4094)> no dot1x guest-vlan Copyright 2023 TRENDnet. All Rights Reserved.
Page 265 This command configures dot1x with default values for this port. The previous configurations on this port are reset to the default values. These details are not displayed but are the basic settings for a port. Syntax dot1x default Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 266 Syntax dot1x max-req <count(1-10)> no dot1x max-req Mode Interface Configuration Mode 4.1.91 dot1x max-start Command Objective This command sets the maximum number of EAPOL retries to the authenticator.The value range is 1 to 65535. Copyright 2023 TRENDnet. All Rights Reserved.
Page 267 This command enables periodic re-authentication from authenticator to client. The periodic re-authentication is requested to ensure if the same supplicant is accessing the protected resources. The amount of time between periodic re-authentication attempts can be configured manually. Copyright 2023 TRENDnet. All Rights Reserved.
Page 268 Command Objective This command sets the dot1x timers. The timer module manages timers, creates memory pool for timers, creates timer list, starts and stops timer. It provides handlers to respective expired timers. Copyright 2023 TRENDnet. All Rights Reserved.
Page 269 {quiet-period <short(0-65535)> | {reauth-period | server- timeout | supp-timeout | tx-period | start-period | held-period | auth-period} <short(1-65535)>} no dot1x timeout {quiet-period | reauth-period | server-timeout | supp- timeout | tx-period | start-period | held-period | auth-period} Copyright 2023 TRENDnet. All Rights Reserved.
Page 270 Configures the number of seconds that the switch waits for a response to an EAP-request/identity frame, from the client before retransmitting the request. • start-period- Configures the number of seconds that the supplicant waits between successive retries to the authenticator. Copyright 2023 TRENDnet. All Rights Reserved.
Page 271 The different Modes employed to the ports offer varied access levels. The 802.1x protocol is supported on both Layer 2 static-access ports and Layer 3 routed ports. Copyright 2023 TRENDnet. All Rights Reserved.
Page 273 Causes the port to remain in the unauthorized state, ignoring all attempts by the client to authenticate. The switch cannot provide authentication services to the client through the interface. Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 274 TL2-F7120 TRENDnet User’s Guide dot1x guest-vlan enable Command Objective This command enables/disables guest-vlan feature. Syntax dot1x guest-vlan enable no dot1x guest-vlan enable Mode Interface Configuration Mode 4.1.145 show dot1x Copyright 2023 TRENDnet. All Rights Reserved.
Page 275 Syntax show dot1x [{ interface <interface-type> <interface-id> | statistics interface <interface-type> <interface-id> | supplicant-statistics interface <interface-type> <interface-id>|local-database | mac-info [address <aa.aa.aa.aa.aa.aa>] | mac-statistics [address <aa.aa.aa.aa.aa.aa>] | all }] Copyright 2023 TRENDnet. All Rights Reserved.
Page 276 MAC session or the specified MAC address. • mac-statistics [address <aa.aa.aa.aa.aa.aa>] - Displays dot1x MAC statistic for all MAC session or the specified MAC address. • - Displays dot1x status for all interfaces. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 277 TL2-F7120 TRENDnet User’s Guide 4.1.146 show dot1x guest-vlan Command Objective Displays dot1x Guest Vlan information. Syntax show dot1x guest-vlan Mode Privileged EXEC Mode 4.1.147 dot1x re-authenticate Copyright 2023 TRENDnet. All Rights Reserved.
Page 278 This value is a combination of slot number and port number separated by a slash. For Example: 0/1 represents that the slot number is 0 and port number is 1. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 279 This command exits the current mode and reverts to the mode used prior to the current mode. Syntax exit Description This command exits the current mode and reverts to the mode used prior to the current mode. Mode All mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 280 Parameter broadcast - Broadcast packets. • unknown-multicast –Unknown multicast packets. Description • - Unknown unicast packets. • level - Storm-control suppression level as a total number of packets per second. Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 281 { output | input } [<integer(1-80000000)>] no rate-limit { output | input } • Parameter output – egress limitation. • input –ingress limitation. Description • <integer(1-80000000)> -Line rate in kbps. Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 282 Syntax qos {enable | disable} • Parameter enable - Enables QoS subsystem • disable - Disables Qos subsystem Description Mode Global Configuration Mode 4.1.151 qos trust Command Objective This command sets qos trust mode. Copyright 2023 TRENDnet. All Rights Reserved.
Page 283 – trust cos, if cos not set, trust dscp. Mode Global Configuration Mode 4.1.152 priority-map Command Objective This command sets the type of the incoming priority mapping to queue. The no form of the command sets default value. Copyright 2023 TRENDnet. All Rights Reserved.
Page 284 [<integer(0-63)>] [<integer(0-63)>] to <integer(0-7)> • Parameter vlanPri– Vlan priority. • ipDscp– DSCP. Description • <integer(0-63)> –Priority value. (0-7) for vlanPri, (0-63) for ipDscp. • integer(0-7) – Queue id. Mode Global Configuration Mode 4.1.153 class-policy Copyright 2023 TRENDnet. All Rights Reserved.
Page 285 This command creates a qos policy. The no form of the command deletes a qos policy. Syntax class-policy <string(23)> no class-policy <string(23)> • Parameter <string(23)>– Name of qos policy. Description Mode Global Configuration Mode 4.1.154 qos interface Copyright 2023 TRENDnet. All Rights Reserved.
Page 286 - Default ingress user priority for the port. Mode Global Configuration Mode 4.1.155 match policy – tcp/udp Command Objective This command specifies the TCP/UDP packets to be forwarded based on the associated parameters. Copyright 2023 TRENDnet. All Rights Reserved.
Page 287 <short (1-4094)> - VLAN value to match against incoming packets. • vlan-priority <short (0-7)> - VLAN priority value to match against incoming packets. • - Transport Control Protocol. • - User Datagram Protocol. Copyright 2023 TRENDnet. All Rights Reserved.
Page 288 <short (0-63)> - Differentiated services code point provides the quality of service control. • tos <short(0-7)> - set tos to value. • dscp <short (0-63)> - set dscp to value. Mode Policy Map Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 289 <short (0-7)>] icmp {any | host <ip_addr>| <ip_addr> <ip_mask> } { any | host <ip_addr> | <ip_addr> <ip_mask> } [type <short(0-255)>] [code <short(0-255)>] [dscp <integer (0-63)>] [action { vpt <short(0-7)> | dscp <short (0-63)>}] Copyright 2023 TRENDnet. All Rights Reserved.
Page 290 ■ the IP Address of the network or the host that the packet is destined for and the network mask to use with the destination address. • type <short (0-255)> message type Copyright 2023 TRENDnet. All Rights Reserved.
Page 291 - message code • dscp <short (0-63)> - Differentiated services code point provides the quality of service control. • tos <short(0-7)> - set tos to value. • dscp <short (0-63)> - set dscp to value. Copyright 2023 TRENDnet. All Rights Reserved.
Page 292 <short (0-7)>] { ip | ospf | pim | <short (1-255)>} {any | host <ip_addr>| <ip_addr> <ip_mask> } { any | host <ip_addr> | <ip_addr> <ip_mask> } [dscp <integer (0-63)>] [action { vpt <short(0-7)> | dscp <short (0-63)>}] Copyright 2023 TRENDnet. All Rights Reserved.
Page 293 <short (0-7)> - VLAN priority value to match against incoming packets. • any | host <ip_addr>| <ip_addr> <ip_mask> - Source IP address can be ■ ‘any’ or ■ the dotted decimal address or Copyright 2023 TRENDnet. All Rights Reserved.
Page 294 - Differentiated services code point provides the quality of service control. • tos <short(0-7)> - set tos to value. • dscp <short (0-63)> - set dscp to value. Mode Policy Map Configuration Mode 4.1.158 no class-policy Copyright 2023 TRENDnet. All Rights Reserved.
Page 295 Parameter <string(31)> –Name of qos policy. Description Mode Global Configuration Mode 4.1.159 show qos global info Command Objective This command displays QoS related global configurations. Syntax show qos global info Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 296 Command Objective This command displays the priority mapping to queue. Syntax show priority-map in-priority-type { vlanPri | ipDscp } • Parameter vlanPri– Vlan priority. • ipDscp– DSCP. Description Mode Privileged EXEC Mode 4.1.161 show class-policy Copyright 2023 TRENDnet. All Rights Reserved.
Page 297 –Name of qos policy. • iftype - Interface type. Description • ifnum - Interface number. Mode Privileged EXEC Mode 4.1.162 show scheduler Command Objective This command displays the configured Scheduler. Syntax show scheduler Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 298 This command displays the configured default ingress user priority for a port. Syntax show qos def-user-priority [interface <iftype> <ifnum>] • Parameter iftype - Interface type. • ifnum - Interface number. Description Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 299 This command enable/disable qos trust on port. Syntax qos trust {enable | disable} • Parameter enable –enable qos trust on port. • disable - disable qos trust on port. Description Mode Interface Configuration Mode 4.1.165 service-policy Copyright 2023 TRENDnet. All Rights Reserved.
Page 300 The no form of this command removes qos policy from the interface. Syntax service-policy <string(31)> in no service-policy <string(31)> • Parameter <string(31)> –Name of qos policy. Description Mode Interface Configuration Mode . RADIUS 4.1.166 radius-server host Copyright 2023 TRENDnet. All Rights Reserved.
Page 301 • host-name - Configures the DNS (Domain Name System) name of the RADIUS server host. This feature has been included to adhere to the Industry Standard CLI syntax. This feature is currently not supported. Copyright 2023 TRENDnet. All Rights Reserved.
Page 302 - Sets the RADIUS server as the primary server. Only one server can be configured as the primary server, any existing primary server will be replaced, when the command is executed with this option. Copyright 2023 TRENDnet. All Rights Reserved.
Page 303 This command displays RADIUS server Host information which contains, Index, Server address, Shared secret, Radius Server status, Response Time, Maximum Retransmission, Authentication Port and Accounting Port. Syntax show radius server [{<ucast_addr> | <ip6_addr> | <string>}] Copyright 2023 TRENDnet. All Rights Reserved.
Page 304 RADIUS server host. • <string>- Displays the name of the RADIUS server host. This maximum value of the string is of size 32. Mode Privileged EXEC Mode 4.1.168 show radius statistics Copyright 2023 TRENDnet. All Rights Reserved.
Page 305 Syntax show radius statistics Mode Privileged EXEC Mode RMON 4.1.169 set rmon Command Objective This command is used to enable or disable the RMON feature. Syntax set rmon {enable | disable} Copyright 2023 TRENDnet. All Rights Reserved.
Page 306 Command Objective This command sets an alarm on a MIB object. The Alarm group periodically takes statistical samples from variables in the probe and compares them to thresholds that have been configured. Copyright 2023 TRENDnet. All Rights Reserved.
Page 307 | etherStatsPkts128to255Octets | etherStatsPkts256to511Octets | etherStatsPkts512to1023Octets | etherStatsPkts1024to1518Octets } <short (1-65535)> { absolute | delta } rising-threshold <integer (0-2147483647)> [<integer (1-65535)>] falling-threshold <integer (0-2147483647)> [<integer (1-65535)>] [owner <string (127)>] no rmon alarm <number (1-65535)> Copyright 2023 TRENDnet. All Rights Reserved.
Page 308 Compares the value of the selected variable with the thresholds at the end of the sampling interval. • delta- Subtracts the value of the selected variable at the last sample from the current value, and the difference is compared with the thresholds at the end of the sampling interval. Copyright 2023 TRENDnet. All Rights Reserved.
Page 309 When the current sampled value is lesser than or equal to the configured Falling threshold, and the value at the last sampling interval is greater than this threshold, a single event will be generated. This value ranges between 0 and 2147483647. Copyright 2023 TRENDnet. All Rights Reserved.
Page 310 (127)>- Sets the entity that are configured this entry. Mode Global Configuration Mode 4.1.171 rmon event Command Objective This command adds an event to the RMON event table. The added event is associated with an RMON event number. Copyright 2023 TRENDnet. All Rights Reserved.
Page 311 127. • trap<community (127)>- Generates a trap, The SNMP community string is to be passed for the specified trap. This value is a string with a maximum value of 127. Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 312 This command enables RMON statistic collection on the interface/ VLAN. The no form of the command disables RMON statistic collection on the interface/ VLAN. Syntax rmon collection stats <index (1-65535)> [owner <ownername (127)>] no rmon collection stats <index (1-65535)> Copyright 2023 TRENDnet. All Rights Reserved.
Page 313 Command Objective This command enables history collection of interface/ VLAN statistics in the buckets for the specified time interval. The no form of the command disables the history collection on the interface/VLAN. Copyright 2023 TRENDnet. All Rights Reserved.
Page 314 RMON collection history group of statistics. This is the requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this History Control EntryThe polling cycle Copyright 2023 TRENDnet. All Rights Reserved.
Page 315 (127)>- Configures the name of the owner of the RMON group of statistics. Mode Interface Configuration Mode / Config VLAN Mode 4.1.174 show rmon Command Objective This command displays the RMON statistics, alarms, events, and history configured on the interface. Copyright 2023 TRENDnet. All Rights Reserved.
Page 316 Alarm module calls events module. • history- Displays the history of the configured RMON. • overview- Displays only the overview of rmon history entries. Copyright 2023 TRENDnet. All Rights Reserved.
Page 317 This command enables SNMP agent which provides an interface between a SNMP manager and a switch. The agent processes SNMP packets received from the manager, frames the appropriate response packets and sends them to the manager. Syntax enable snmpagent Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 318 This command enables SNMP agent which provides an interface between a SNMP manager and a switch. The agent processes SNMP packets received from the manager, frames the appropriate response packets and sends them to the manager. Copyright 2023 TRENDnet. All Rights Reserved.
Page 319 - Indicates the location of the context through which the management information is accessed when using the community string specified by the corresponding instance of snmp community name Mode Global Configuration Mode 4.1.178 snmp group Copyright 2023 TRENDnet. All Rights Reserved.
Page 320 Sets the security model for SNMP ■ - Sets the SNMP version as Version 1. ■ - Sets the SNMP version as Version 2. ■ - Sets the SNMP version as Version 3. Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 321 <GroupName> {v1 | v2c | v3 {auth | noauth | priv}} [read <ReadView | none>] [write <WriteView | none>] [notify <NotifyView | none>] no snmp access <GroupName> {v1 | v2c | v3 {auth | noauth | priv}} Copyright 2023 TRENDnet. All Rights Reserved.
Page 322 - Mentions the MIB view of the SNMP context to which write access is authorized by this entry • notify - Mentions the MIB view of the SNMP context to which notification access is authorized by this entry Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 323 The no form of the command resets the engine ID to the default value. Syntax snmp engineid <EngineIdentifier> no snmp engineid Mode Global Configuration Mode 4.1.181 snmp view Copyright 2023 TRENDnet. All Rights Reserved.
Page 324 - Specifies the sub tree value for the particular view. • mask <OIDMask> - Specifies a mask value for the particular view. • included - Allows access to the subtree • excluded - Denies access to the subtree Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 325 The no form of the command removes the configured SNMP target address. Syntax snmp targetaddr <TargetAddressName> param <ParamName> {<IPAddress> | <IP6Address>} [timeout <Seconds(1-1500)] [retries <RetryCount(1-3)] [taglist <TagIdentifier | none>] [port <integer (1- 65535)>] no snmp targetaddr <TargetAddressName> Copyright 2023 TRENDnet. All Rights Reserved.
Page 326 SNMP. The taglist can also be set as none using the none option. • port <integer (1-65535)> - Configures a port number through which the generated SNMP notifications are sent to the target address. The value ranges between 1 and 65535. Copyright 2023 TRENDnet. All Rights Reserved.
Page 327 <ParamName> user <UserName> security-model {v1 | v2c | v3 {auth | noauth | priv}} message-processing {v1 | v2c | v3} no snmp targetparams <ParamName> • Parameter <ParamName> - Sets a unique identifier of the parameter. Description Copyright 2023 TRENDnet. All Rights Reserved.
Page 328 ■ – Sets the SNMP version as Version 2. ■ – Sets the SNMP version as Version 3. It is the most secure model as it allows packet encryption with the priv key word Copyright 2023 TRENDnet. All Rights Reserved.
Page 329 This command configures the SNMP user details. The no form of the command removes the SNMP user details. Syntax snmp user <UserName> [auth {md5 | sha} <passwd> [priv {{{DES | AES_CFB128} <passwd> } | None}]] no snmp user <UserName> Copyright 2023 TRENDnet. All Rights Reserved.
Page 330 – Configures Advanced Encryption Standard (AES) algorithm for encryption. ■ <Passwd> - Sets the authentication password that will be used for the configured authentication algorithm. ■ None - Sets no encryption configurations. Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 331 Command Objective This command configures the SNMP notification details. The no form of this command removes the SNMP notification details. Syntax snmp notify <NotifyName> tag <TagName> type {Trap | Inform} no snmp notify <NotifyName> Copyright 2023 TRENDnet. All Rights Reserved.
Page 333 This command sets the system name. Syntax system location <system name> Mode Global Configuration Mode 4.1.91 system location Command Objective This command sets the location name. Syntax system location <location name> Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 334 Command Objective This command sets the contact information. Syntax system contact <contact info> Mode Global Configuration Mode 4.1.93 show snmp Command Objective This command displays the status information of SNMP communications. Syntax show snmp Copyright 2023 TRENDnet. All Rights Reserved.
Page 335 TL2-F7120 TRENDnet User’s Guide Mode Privileged EXEC Mode 4.1.91 show snmp community Command Objective This command displays the configured SNMP community details. Syntax show snmp community Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 336 Command Objective This command displays the configured SNMP groups. Syntax show snmp group Mode Privileged EXEC Mode 4.1.93 show snmp group access Command Objective This command displays the configured SNMP group access details. Copyright 2023 TRENDnet. All Rights Reserved.
Page 337 TL2-F7120 TRENDnet User’s Guide Syntax show snmp group access Mode Privileged EXEC Mode 4.1.91 show snmp engineid Command Objective This command displays the Engine Identifier. Syntax show snmp engineID Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 338 This command displays the configured SNMP Tree views. Syntax show snmp viewtree Mode Privileged EXEC Mode 4.1.91 show snmp targetaddr Command Objective This command displays the configured SNMP target Addresses. Syntax show snmp targetaddr Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 339 TL2-F7120 TRENDnet User’s Guide 4.1.92 show snmp targetparam Command Objective This command displays the configured SNMP Target Address Params. Syntax show snmp targetparam Mode Privileged EXEC Mode 4.1.93 show snmp user Copyright 2023 TRENDnet. All Rights Reserved.
Page 340 This command displays the configured SNMP users. Syntax show snmp user Mode Privileged EXEC Mode 4.1.91 show snmp notif Command Objective This command displays the configured SNMP Notification types. Syntax show snmp notif Mode Privileged EXEC Mode . SNTP Copyright 2023 TRENDnet. All Rights Reserved.
Page 341 - Enables SNTP client module and sends a request to the host for time synchronization. Description • disabled - Disables SNTP client module and no request is sent to the host for time synchronization. Mode SNTP Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 342 Command Objective This command transmits or receives LLDP frames from the server to the LLDP module. Syntax set sntp client port <portno(1-65535)> no sntp client port Mode SNTP Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 343 - Sets the client time zone as after or before UTC. Plus indicates ⚫ forward time zone and minus indicates backward time zone. • UTC-offset value as - Sets the UTC offset value in hours +00:00 to +14:00 -00:00 to -12:00 Mode SNTP Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 344 The dates of DST may change from year to year. The no form of this command disables the Daylight Saving Time. Syntax set sntp client clock-summer-time <week-day-month,hh:mm> <week- day- month,hh:mm> Eg: set sntp client clock-summer-time First-Sun- Mar,05:10 Second-Sun-Nov,06:10 no sntp client clock summer-time Copyright 2023 TRENDnet. All Rights Reserved.
Page 345 - Time in hours and minutes Mode SNTP Configuration Mode 4.1.191 set sntp unicast-server Command Objective This command configures SNTP unicast server. The no form of this command deletes the sntp unicast server attributes and sets to default value Copyright 2023 TRENDnet. All Rights Reserved.
Page 346 • version 4 - Sets the SNTP version as 4. • port <integer(1025-36564)> - Selects the port identifier numbers in the selected server. This value ranges between 1025 and 36564. Mode SNTP Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 347 This command displays the current time. Syntax show sntp clock Mode User / Privileged EXEC Mode 4.1.92 show sntp status Command Objective This command displays SNTP status. Syntax show sntp status Mode User / Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 348 The spanning tree operation can be enabled in the switch only if the spanning tree functionality is not shutdown in the switch. The type of spanning tree Mode should be set, if the functionality is already shutdown. Copyright 2023 TRENDnet. All Rights Reserved.
Page 349 The current selected type of spanning tree is enabled and the existing spanning tree type is disabled in the switch. Syntax spanning-tree mode {mst|rst} Copyright 2023 TRENDnet. All Rights Reserved.
Page 350 - Configures the switch to execute RSTP for preventing undesirable loops. RSTP provides rapid recovery of connectivity following the failure of a bridge/bridge port or a LAN Mode Global Configuration Mode 4.1.194 spanning-tree timers Copyright 2023 TRENDnet. All Rights Reserved.
Page 351 The no form of this command resets the spanning tree timers to its default values. The spanning tree timers are reset to its default value, even if the spanning tree Mode is changed. Copyright 2023 TRENDnet. All Rights Reserved.
Page 352 This spanning tree timer’s configuration is not supported in PVRST Mode. Syntax spanning-tree {forward-time <seconds(4-30)> | hello-time <seconds(1- 2)> | max-age <seconds(6-40)>} no spanning-tree { forward-time | hello-time | max-age } Copyright 2023 TRENDnet. All Rights Reserved.
Page 353 The spanning tree topology is re-computed after this time interval. This value ranges between 6 and 40 seconds. In MSTP, this time configuration is applied for IST root (that is, MSTI 0). Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 354 The type of spanning tree Mode should be set, if the functionality is already shutdown. Syntax spanning-tree transmit hold-count <value (1-10)> no spanning-tree transmit hold-count Copyright 2023 TRENDnet. All Rights Reserved.
Page 355 Mode is changed. In RSTP, this value is used during the election of root. In MSTP, this value is used during the election of CIST root, CIST regional root and IST root. Copyright 2023 TRENDnet. All Rights Reserved.
Page 356 The priority value can be configured in the switch, only if the spanning tree functionality is not shutdown in the switch. The type of spanning tree Mode should be set, if the functionality is already shutdown. Syntax spanning-tree [mst <instance-id>] priority <value(0-61440)> no spanning-tree [mst <instance-id(1-64)>] priority Copyright 2023 TRENDnet. All Rights Reserved.
Page 357 0 and 61440. The value should be set in steps of 4096, that is, you can set the value as 0, 4096, 8192, 12288 and so Mode Global Configuration Mode 4.1.196 spanning-tree mst forward-time Copyright 2023 TRENDnet. All Rights Reserved.
Page 358 The STP forward timers can be configured in the switch, only if the spanning tree functionality is not shutdown in the switch. The type of spanning tree Mode should be set, if the functionality is already shutdown. Copyright 2023 TRENDnet. All Rights Reserved.
Page 359 TL2-F7120 TRENDnet User’s Guide Syntax spanning-tree mst forward-time <seconds(4-30)> no spanning-tree mst forward-time Mode Global Configuration Mode 4.1.91 spanning-tree mst max-age Copyright 2023 TRENDnet. All Rights Reserved.
Page 360 The timer value ranges between 6 and 40 seconds. The no form of the command sets the max-age timer to the default value. ✏ The values configured for the spanning tree forward timers should satisfy the following conditions: Copyright 2023 TRENDnet. All Rights Reserved.
Page 361 The type of spanning tree Mode should be set, if the functionality is already shutdown. Syntax spanning-tree mst max-age <seconds(6-40)> no spanning-tree mst max-age Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 362 This command can be executed successfully, only if the spanning tree functionality is not shutdown in the switch. The type of spanning tree Mode should be set as mst. Syntax spanning-tree mst hello-time<value(1-2)> no spanning-tree mst hello-time Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 363 Port protocol migration count · For MSTP, the information contains number of: Port forward transitions · Port received BPDUs · Port transmitted BPDUs · Port invalid BPDUs received · Port protocol migration count · Copyright 2023 TRENDnet. All Rights Reserved.
Page 364 The statistics information can be deleted, only if the spanning tree functionality is not shutdown in the switch. The type of spanning tree Mode should be set, if the functionality is already shutdown. clear spanning-tree [mst <instance-id>] counters[interface <interface- type> <interface-id>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 365 For Example: 0/1 represents that the slot number is 0 and port number is 1. Only port-channel ID is provided, for interface type port-channel. For Example: 1 represents port-channel ID. Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 366 The no form of this command resets maximum MSTP instance value to its default value. ✏ This command can be executed successfully, only if the spanning tree functionality is started and enabled in the switch. The type of spanning tree Mode should be set as mst. Copyright 2023 TRENDnet. All Rights Reserved.
Page 367 This command is a standardized implementation of the existing command; spanning-tree priority. It operates similar to the existing command. The no form of the command disables BPDU transmission and reception on the interface. Copyright 2023 TRENDnet. All Rights Reserved.
Page 368 The priority value is set as 24576. • secondary - Sets the switch as a secondary root, if the primary root fails. The priority value is set as 28672. Copyright 2023 TRENDnet. All Rights Reserved.
Page 369 This command can be executed successfully, only if the spanning tree functionality is started and enabled in the switch. The type of spanning tree Mode should be set as mst. Syntax spanning-tree mst configuration Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 370 IST to disseminate STP topology information for other STP instances. The no form of this command resets the name to its default value. Syntax name <string(optional max Length 32)> no name Mode MSTP Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 371 This command configures the revision number for the MST region. This value ranges between 0 and 65535. The no form of this command resets the revision number to its default value. Syntax revision <value(0-65535)> no revision Mode MSTP Configuration Mode 4.1.91 instance Copyright 2023 TRENDnet. All Rights Reserved.
Page 372 The no form of this command deletes the instance / unmaps specific VLANs from the MST instance. Syntax instance <instance-id(1-64)> vlan <vlan-range> no instance <instance-id (1-64)> [vlan <vlan-range>] Mode MSTP configuration Mode 4.1.92 spanning-tree auto-edge Copyright 2023 TRENDnet. All Rights Reserved.
Page 373 The automatic detection of Edge port parameter can be configured in the switch, only if the spanning tree functionality is not shutdown in the switch. The type of spanning tree Mode should be set, if the functionality is already shutdown. Copyright 2023 TRENDnet. All Rights Reserved.
Page 374 TL2-F7120 TRENDnet User’s Guide Syntax spanning-tree auto-edge no spanning-tree auto-edge Mode Interface Configuration Mode 4.1.91 spanning-tree - Properties of an interface Copyright 2023 TRENDnet. All Rights Reserved.
Page 375 STP is intended to be enabled on that interface. This leads To STP scaling issues and this problem is solved by having control at STP module on the port entry creation at STP module itself. Copyright 2023 TRENDnet. All Rights Reserved.
Page 376 TL2-F7120 TRENDnet User’s Guide Syntax spanning-tree [{cost <value(0-200000000)>|disable|link-type{point-to- point|shared}|port-priority <value(0-240)>}] no spanning-tree [{cost |disable|link-type|port-priority}] Copyright 2023 TRENDnet. All Rights Reserved.
Page 377 – The port is treated as if it is connected to a point-to-point link. ◆ shared - The port is treated as if it is using a shared media connection. • port-priority – 128 Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 378 The type of spanning tree Mode should be set as mst. Syntax spanning-tree mst <instance-id(1-64)> { cost <value(1-200000000)>| port- priority <value(0-240)> | disable } no spanning-tree mst <instance-id(1-64)>{cost|port-priority | disable} Copyright 2023 TRENDnet. All Rights Reserved.
Page 379 - Disables the spanning tree operation on the port. The port does not take part in the execution of spanning tree operation for preventing undesirable loops in the network. Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 380 STP compatibility version used, configured spanning tree Mode, bridge and port level spanning tree statistics information, and details of ports enabled in the switch. The port details contain port ID, port role, port state, port cost, port priority and link type. Copyright 2023 TRENDnet. All Rights Reserved.
Page 381 This value represents unique name of the switch context. This value is a string with the maximum size as 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 383 This value represents unique Description name of the switch context. This value is a string with the maximum size as 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.202 show spanning-tree active Copyright 2023 TRENDnet. All Rights Reserved.
Page 384 This command can be executed successfully, only if the spanning tree functionality is not shutdown in the switch. The type of spanning tree Mode should be set, if the functionality is already shutdown. Syntax show spanning-tree active [detail] [ switch <context_name>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 385 This value is a string with the maximum size as 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.203 show spanning-tree interface Copyright 2023 TRENDnet. All Rights Reserved.
Page 386 <interface-id> - Displays the information about the specified interface identifier. This is a unique value that represents the specific interface. This value is a combination of slot number and port number separated by a slash. For Example: 0/1 represents Copyright 2023 TRENDnet. All Rights Reserved.
Page 389 This value represents unique name of the switch context. This value is a string with the maximum size as 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.205 show spanning-tree bridge Copyright 2023 TRENDnet. All Rights Reserved.
Page 390 Syntax show spanning-tree bridge [{ address | forward-time | hello-time | id | max- age | protocol | priority | detail }] [ switch <context_name>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 391 This value is a string with the maximum size as 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.206 show spanning-tree mst - CIST or specified mst Instance Copyright 2023 TRENDnet. All Rights Reserved.
Page 392 This command can be executed successfully, only if the spanning tree functionality is not shutdown in the switch. The type of spanning tree Mode should be set as mst. Syntax show spanning-tree mst [<instance-id(1-64)>] [detail] [ switch <context_name>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 393 This value represents unique name of the switch context. This value is a string with the maximum size as 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.207 show spanning-tree mst configuration Copyright 2023 TRENDnet. All Rights Reserved.
Page 394 This value represents Description unique name of the switch context. This value is a string with the maximum size as 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 395 The type of spanning tree Mode should be set as mst. Syntax show spanning-tree mst [<instance-id(1-64)>] interface <interface- type> <interface-id> [{ stats | hello-time | detail }] Copyright 2023 TRENDnet. All Rights Reserved.
Page 396 - Displays the hello time of the MSTIs assigned to the specified interface. • detail - Displays detailed multiple spanning tree port specific information for the specified interface. The information contain port priority, port cost, root address, priority and cost, IST Copyright 2023 TRENDnet. All Rights Reserved.
Page 397 4.1.209 ip ssh server Command Objective This command enables the SSH system The no form of the command disables the SSH system. Syntax ip ssh server no ip ssh server Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 398 Global Configuration Mode . SSL 4.1.211 show ip http secure server status Command Objective This command displays SSL status and configuration information. Information such as HTTP secure server status, HTTP secure server ciphersuite are displayed. Copyright 2023 TRENDnet. All Rights Reserved.
Page 399 This command enables the server status to establish the secure layer in the network The no form of the command disables the server status. ip http secure server Syntax no ip http secure server Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 400 Command Objective This command displays the information about the syslog logging server table. Syntax show logging-server Mode Privilege EXEC Mode 4.1.214 show logging Command Objective This command displays all the logging status and configuration information. Copyright 2023 TRENDnet. All Rights Reserved.
Page 401 The logging process controls the distribution of logging messages to the various destinations. Syntax logging severity { alerts | critical | debugging | emergencies | errors | informational | notification | warnings } Copyright 2023 TRENDnet. All Rights Reserved.
Page 402 4 | warnings - Warning conditions. ■ 5 | notification - Normal but significant conditions. ■ 6 | informational - Informational messages. ■ 7 | debugging – Debugging messages. Mode Global Configuration Mode 4.1.216 logging-service Copyright 2023 TRENDnet. All Rights Reserved.
Page 403 Parameter enable - Syslog enabled. • disable - Syslog disabled. Description Mode Global Configuration Mode 4.1.217 clear logs Command Objective This command clears the system syslog buffers. Syntax clear logs Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 404 {facility {local0 | local1 | local2 | local3 | local4 | local5 | local6 | local7}} {severity { emergencies | alerts | critical | errors | warnings | notification | informational| debugging}} {ipv4 <ucast_addr> |ipv6 <ip6_addr> | <string>} [ port <integer(0-65535)>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 405 <string> - Configures the host name for a server to log an entry. • port<integer(0-65535)> - Sets the port number through which it sends the syslog message. The value ranges between 0 and 65535. Copyright 2023 TRENDnet. All Rights Reserved.
Page 406 VLAN is already created. • <vlan –id>- This is a unique value that represents the specific VLAN. This value ranges between 1 and 4094. Syntax vlan <vlan-id> no vlan <vlan-id> Mode Global Configuration Mode/ Switch Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 407 VLAN. The VLAN can also be activated using the vlan active command. Syntax ports [add] ([<interface-type> <0/a-b,0/c,...>] [<interface-type> <0/a- b,0/c,...>] [port-channel <a,b,c-d>] [pw <a,b,c-d>] [pw <a,b,c-d>]) Copyright 2023 TRENDnet. All Rights Reserved.
Page 408 [port-channel <a,b,c-d>] [pw <a,b,c-d>] [ac <a,b,c-d>] [all] [untagged ([<interface-type> <0/a-b,0/c,...>] [<interface-type> <0/a- b,0/c,...>] [port- channel <a,b,c-d>] [pw <a,b,c-d>] [ac <a,b,c-d>] [all])] [forbidden ([<interface-type> <0/a-b,0/c,...>] [<interface-type> <0/a- b,0/c,...>] [port- channel <a,b,c-d>] [pw <a,b,c-d>] [ac <a,b,c-d>] [all])] [name <vlan-name>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 409 <a,b, c-d>- Configures the specified attachment circuit interface as a member port. This value ranges between 1 and 65535. Use comma as a separator without space while configuring list of interfaces. Example: 1,3. Copyright 2023 TRENDnet. All Rights Reserved.
Page 410 • name<vlan-name>- Configures the unique name of the VLAN. This name is used to identify the VLAN and is an administratively assigned string with the maximum size as 32. Mode Config-VLAN Mode 4.1.221 exit Copyright 2023 TRENDnet. All Rights Reserved.
Page 411 VLAN ID that is to be assigned to untagged frames or priority-tagged or C-VLAN frames received on the port. The PVID is used for port based VLAN type membership classification. This value ranges between 1 and 4094. Syntax switchport pvid <vlan-id> Copyright 2023 TRENDnet. All Rights Reserved.
Page 412 Interface Configuration mode (Physical / Port channel) TL2-F7120# c t Example TL2-F7120(config)# interface gigabitethernet 0/13 TL2-F7120(config-if)# switchport pvid 3 TL2-F7120(config-if)# exit TL2-F7120(config)# exit TL2-F7120# show vlan port config port gigabitethernet 0/13 Vlan Port configuration table ------------------------------- Port Gi0/13 Copyright 2023 TRENDnet. All Rights Reserved.
Page 413 Subnet Based Support : Disabled Port-and-Protocol Based Support Enabled Default Priority Dot1x Protocol Tunnel Status : Peer LACP Protocol Tunnel Status : Peer Spanning Tree Tunnel Status : Peer MVRP Protocol Tunnel Status : Peer Copyright 2023 TRENDnet. All Rights Reserved.
Page 414 Protocol Tunnel Status : Peer Filtering Utility Criteria : Default Port Protected Status : Disabled ------------------------------------------------------- TL2-F7120# 4.1.223 switchport acceptable-frame-type Command Objective This command is to configure the acceptable frame types for a port. Copyright 2023 TRENDnet. All Rights Reserved.
Page 415 Only the untagged or priority tagged frames received on the port are accepted and subjected to ingress filtering. The tagged frames received on the port are rejected. Mode Interface Configuration mode (Physical / Port channel) Copyright 2023 TRENDnet. All Rights Reserved.
Page 416 TL2-F7120# c t Example TL2-F7120(config)# interface gigabitethernet 0/13 TL2-F7120(config-if)# switchport acceptable-frame-type untaggedAndPrioritytagged TL2-F7120(config-if)# exit TL2- F7120(config)# exit TL2-F7120# show vlan port config port gigabitethernet 0/13 Vlan Port configuration table ------------------------------- Port Gi0/13 Bridge Port Type : Customer Bridge Port PVID...
Page 418 MMRP Protocol Tunnel Status : Peer GVRP Protocol Tunnel Status : Peer GMRP Protocol Tunnel Status : Peer IGMP Protocol Tunnel Status : Peer Filtering Utility Criteria : Default Port Protected Status : Disabled ------------------------------------------------------- TL2-F7120# Copyright 2023 TRENDnet. All Rights Reserved.
Page 419 The no form of the command disables ingress filtering feature on the port. All incoming frames received on the port are accepted. Syntax switchport ingress-filter no switchport ingress-filter Mode Interface Configuration mode (Physical / Port channel) Copyright 2023 TRENDnet. All Rights Reserved.
Page 420 VLANs (that are not active) for which the port details are configured. The information contain the member ports, untagged ports, forbidden ports, VLAN name and the status of that VLAN entry. Syntax show vlan [brief | id <vlan-range> | summary] [ switch <context_name>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 421 VLANs, for the specified context. This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Copyright 2023 TRENDnet. All Rights Reserved.
Page 422 VLAN traffic class status, VLAN learning mode, VLAN version number, maximum VLAN ID supported, maximum number of VLANs supported and VLAN unicast MAC learning limit. Syntax show vlan device info [ switch <context_name>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 423 Command Objective This command displays only the list of VLAN features such as traffic class feature, supported in the switch / all contexts. Syntax show vlan device capabilities [ switch <context_name>] Copyright 2023 TRENDnet. All Rights Reserved.
Page 424 Description unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.227 show vlan port config Copyright 2023 TRENDnet. All Rights Reserved.
Page 425 Parameter <interface-type> - Displays the VLAN related port specific information for the specified interface. Description ■ gigabitethernet – A version of LAN standard architecture that supports data transfer up to 1 Gigabit per second. Copyright 2023 TRENDnet. All Rights Reserved.
Page 426 VLANs, for the specified context. This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.228 show vlan statistics Copyright 2023 TRENDnet. All Rights Reserved.
Page 427 This value is a string whose maximum size is 9. For example, the value is provided as 4000-4010 to display the details for VLAN IDs from 4000 to 4010. The details are displayed only for the VLANs that Copyright 2023 TRENDnet. All Rights Reserved.
Page 428 VLANs, for the specified context. This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode 4.1.229 show mac-address-table Copyright 2023 TRENDnet. All Rights Reserved.
Page 429 This value denotes the VLAN ID range for which the entries need to be displayed. This value is a string with the maximum size as 9. For example, the value is provided as 4000-4010 to display the entries for VLAN IDs from 4000 to 4010. Copyright 2023 TRENDnet. All Rights Reserved.
Page 430 VLANs, for the specified context. This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. • Mode Privileged EXEC Mode 4.1.230 show mac-address-table count Copyright 2023 TRENDnet. All Rights Reserved.
Page 431 VLANs, for the specified context. This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 432 MAC entries created in the MAC address table for the specified VLANs Description alone. This value denotes the VLAN ID range for which the entries need to be displayed. This value is a string with Copyright 2023 TRENDnet. All Rights Reserved.
Page 433 VLANs, for the specified context. This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 434 (that is permanent, static and so on), the unicast backbone MAC address of peer backbone edge bridge, and total number of entries displayed. Syntax show mac-address-table dynamic unicast [vlan <string(9)>] [address <ucast_mac>] [{interface <interface-type> <ifnum> | switch <string(32)>}] Copyright 2023 TRENDnet. All Rights Reserved.
Page 435 VLANs, for the specified context. This value represents unique name of the switch context. This value is a string whose maximum size is 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 436 This value represents unique name of Description the switch context. This value is a string with the maximum size as 32. This parameter is specific to multiple instance feature. Mode Privileged EXEC Mode . VOICE-VLAN Copyright 2023 TRENDnet. All Rights Reserved.
Page 437 [{oui-enabled | disabled | auto}] • Parameter oui-enable – Enable voice vlan with OUI. • disabled – Disable voice vlan. Description • auto – Enable voice vlan with LLDP-MED. Mode Global Configuration Mode 4.1.235 voice vlan id Copyright 2023 TRENDnet. All Rights Reserved.
Page 438 4.1.236 voice vlan aging-time Command Objective This command specifies the voice VLAN aging timeout interval in minutes. Syntax voice vlan aging-time <integer(30-65535)> • Parameter <integer(30-65535)> – Timeout in minutes. Description Mode Global Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 439 <integer(0-7)> [remark] • Parameter <integer(0-7)> – cos. • [remark] – Specifies that the L2 user priority is remarked with Description the CoS value. Mode Global Configuration Mode 4.1.238 voice vlan vpt Copyright 2023 TRENDnet. All Rights Reserved.
Page 440 This command specifies the LLDP-MED vlan priority tag. Syntax voice vlan vpt <integer(0-7)> • Parameter <integer(0-7)> – vpt. Description Mode Global Configuration Mode 4.1.239 voice vlan dscp Command Objective This command specifies the LLDP-MED dscp. Syntax voice vlan dscp <integer(0-63)> Copyright 2023 TRENDnet. All Rights Reserved.
Page 441 Parameter add <ucast_mac> – Add voice device mac address prefix to OUI table. • [<string(32)>] - Voice device prefix description. Description • remove <ucast_mac> - Remove voice device mac address prefix from OUI table. Copyright 2023 TRENDnet. All Rights Reserved.
Page 442 TRENDnet User’s Guide Mode Global Configuration Mode 4.1.241 voice vlan enable Command Objective This command specifies the OUI voice vlan enable/disable on interfaces. Syntax voice vlan enable no voice vlan enable Mode Interface Configuration Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 443 –QoS attributes are applied to packets with OUIs in the source MAC address. Description • - QoS attributes are applied to packets that are classified to the Voice VLAN. Mode Interface Configuration Mode 4.1.243 show voice vlan Copyright 2023 TRENDnet. All Rights Reserved.
Page 444 TL2-F7120 TRENDnet User’s Guide Command Objective Show voice vlan state. Syntax show voice vlan [oui-table] • Parameter [oui-table] –Specifies OUI table. Description Mode Privilege EXEC Mode Copyright 2023 TRENDnet. All Rights Reserved.
Page 445: Technical Specifications
• Loopback detection • • MAC address table: 32K entries • CPU/Memory Utilization • Jumbo frames: 10KB • Real-time port statistics • Forwarding mode: store and forward • Forwarding rate: 178.6Mpps (64-byte packet size) Copyright 2023 TRENDnet. All Rights Reserved.
Page 446 Input: 100 – 240V AC, 50/60 Hz, 1.5A • • Dynamic GVRP • Max. Consumption: 20W Port Isolation • • Up to 256 VLAN groups, ID range 1-4094 Fan/Acoustics • Voice VLAN • Quantity: 1 • Dynamic VLAN • Smart Fan Copyright 2023 TRENDnet. All Rights Reserved.
Page 447 210 x 230 x 44mm (8.26 x 9.06 x 1.73 in.) • Rack mountable 1U height Dual 1U rackmount kit option (ETH-F71 sold separately) • Weight • 1.6 kg (3.5 lbs.) Certifications • • • Copyright 2023 TRENDnet. All Rights Reserved.
Page 448: Troubleshooting
Then click Use the following IP address, and make sure to assign your network adapter an IP address in the subnet of 192.168.10.x. Click OK Note: If you are experiencing difficulties, please contact your computer or operating system manufacturer for assistance. Copyright 2023 TRENDnet. All Rights Reserved.
Page 449: Appendix
2. In the Network Preference window, next to "Show:", select Network Status. You'll see b. Click the Network icon. your network status and your IP address settings displayed. c. From the Location drop-down list, select Automatic. Copyright 2023 TRENDnet. All Rights Reserved.
Page 450 1. Apple Menu > System Preferences > Network 2. Select Ethernet from the list on the left. 3. Click the Advanced button. 3. On the Ethernet tab, the Ethernet ID is your MAC Address. Copyright 2023 TRENDnet. All Rights Reserved.
Page 451 Europe – EU Declaration of Conformity one of the following measures: TRENDnet hereby declare that the product is in compliance with the essential requirements • Reorient or relocate the receiving antenna.
Page 452 An RMA number is required in order to initiate warranty service support the event that the RMA unit needs to be replaced, TRENDnet may replace it with a for all TRENDnet products. Products that are sent to TRENDnet for RMA service must refurbished product of the same or comparable model.
Page 453 OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND evidence of the original purchaser's date of purchase. Replacement products may be OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION. THIS DISCLAIMER OF LIABILITY refurbished or contain refurbished materials. If TRENDnet, by its sole determination, is...

TRENDnet TL2-F7120 User Manual

Quick Links

Related Manuals for TRENDnet TL2-F7120

Summary of Contents for TRENDnet TL2-F7120

Table of Contents