Agilent Technologies WireScope 350 User Manual page 73

8r…‡vs’vtÃAvir…Ã8hiyvt
8hyvi…h‡vtÇurÃU r†‡r…
4−6
1 Insert a Fiber SmartProbe
+
SmartProbe
2 Connect a single fiber of each of two duplex test jumpers to the two
Fiber SmartProbes
detector of the other with no coupler.
3 Turn on the WireScope and DualRemote.
4 On the Fiber Main Menu, press Calibration. The Fiber Calibration
screen displays as above.
5 Choose Double Ended, and press Next. the Fiber Detection screen
displays as above.
6 When the message below the diagram reads, "Ready to Calibrate,"
press OK. The Calibration window opens.
7 When the window reads, "Calibration Successful," press OK in the
window. The Fiber Main Menu displays. Leave the transmitter
connection to the Fiber SmartProbes intact. Remove both detector
connections and replace with the previously unused fiber of the
duplex test jumper on each probe.
Method C
Method C is recommended for multi-fiber and small form factor (SFF)
connectors.
1RWH 7rphˆ†rÇurÀˆy‡vsvir…TAAÃp‚rp‡‚…†Ãh…rÂyh…v“rqÃp‚rp‡‚…†Ãr†ˆ…rÇuh‡Ã’‚ˆÃuh‰rÃ
†ryrp‡rqÇurÃ…‚ƒr…Ãp‚rp‡‚…Ç’ƒrÃvÃ‡urÃ6ˆ‡‚‡r†‡ÃTr‡ˆƒÃ†p…rrÆrrà 8u‚‚†vtÇurÃ
8‚rp‡‚…ÃU ’ƒr ‚Ãƒhtr #
1 Insert a Fiber SmartProbe
+
SmartProbe
singlemode or multimode.
1RWH
Tvtyr€‚qrÃAvir…ÃT€h…‡Q…‚ir†Ãˆ†rÃhÃyh†r…Ãyvtu‡Ã†‚ˆ…prÇuh‡Ã…r„ˆv…r†Ãh…€vtȃÃirs‚…rÃ
ˆ†rÃ7rs‚…rÃphyvi…h‡vtÂ…Çr†‡vtÐv‡uÆvtyr€‚qrÃsvir…Ã…‚ir†Ãhyh’†Ãp‚rp‡Ã‡urÃ
ƒ…‚ir†Lj…Ã‚Ã‡urÃXv…rTp‚ƒrÃhqÃ9ˆhySr€‚‡rÃvsȆrqÃhqÐhv‡Ãsv‰rÀvˆ‡r†Ãs‚…À‚†‡Ã
hppˆ…h‡rÃ…rhqvt†
2 Connect special ST or SC to multi-fiber/SFF test jumpers to the two
Fiber SmartProbes. These special transition jumpers are available
from the connector manufacturers.
3 Connect the test jumpers to each other, using a special reference
jumper which mates with the multi-fiber/SFF connector. Special
reference jumpers are manufacturer specific. Contact the connector
manufacturer for details. Connect the WireScope transmitter to the
DualRemote detector, and vice versa.
4 Turn on the WireScope and DualRemote, if necessary.
5 On the Fiber Main Menu, press Calibration. The Fiber Calibration
screen displays as above.
6 Choose Double Ended, and press Next. the Fiber Detection screen
displays as above.
7 When the message below the diagram reads, "Ready to Calibrate,"
press OK. The Calibration window opens.
+
in the WireScope and a Fiber
in the DualRemote. They should both be multimode.
+
with the transmitter of each connected to the
'
+
in the WireScope and a Fiber
in the DualRemote. They should both be either