Page 5
4263B Safety Summary WARNINGS The Agilent Technologies assumes no liability for the customer's failure to comply with these requirements. Note Ground The Instrument DO NOT Operate In An Explosive Atmosphere Keep Away From Live Circuits DO NOT Service Or Adjust Alone...
4263B Certication Warranty General Information Limitation Of Warranty No other warranty is expressed or implied. Agilent Technologies specically disclaims the implied warranties of merchantability and tness for a particular purpose.
4263B Exclusive Remedies The remedies provided herein are buyer's sole and exclusive remedies. Agilent Technologies shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any other legal theory. Assistance...
Page 27
4263B Overview Features 1-2 Getting Started...
Page 28
4263B Accessories Available Note Options Available Getting Started 1-3...
Page 29
4263B Guided Tour of Panels Front Panel Display LINE Switch Chassis Terminal UNKNOWN Terminals Caution DC Bias Key DC Bias ON/OFF Indicator Measurement Time Key Average Key Show Setting Key - (Shift) Current / Voltage Monitor (I&V Mon) Key -...
Page 32
4263B Display Character Display Area Annunciator Measurement Time Trigger Hold Range Load On Comparator On Contact Check Talk Only Remote Key Lock Measurement Settings Shift Getting Started 1-7...
Page 33
4263B Rear Panel Caution GPIB Interface gpib External DC Bias Terminal LINE Fuse Holder Handler Interface External Trigger Terminal Serial Number Plate LINE Voltage Selector Power Cord Receptacle 1-8 Getting Started...
4263B Incoming Inspection Warning To avoid hazardous electrical shock, do not turn on the 4263B when there are signs of shipping damage to any portion of the outer enclosure (for example, covers, panel, or display) Providing clearance to dissipate heat at installation site...
4263B Power Cable Warning For protection from electrical shock, the power cable ground must not be defeated. The power plug must be plugged into an outlet that provides a protective earth ground connection. 1-10 Getting Started...
Page 36
4263B Figure 1-1. Power Cable Supplied Getting Started 1-11...
4263B Preparation for Turning On Setting the Line Voltage Power Line Voltage : Power Line Frequency : Power Consumption : Fuse Figure 1-2. Voltage Selector and Fuse Table 1-1. Line Voltage Selection Voltage Selector Power Line Required Fuse Voltage 1-12 Getting Started...
Page 38
4263B Turning On the 4263B and Setting the Line Frequency Note Getting Started 1-13...
Page 44
4263B Connecting a Test Fixture Figure 1-3. Connecting a Test Fixture Getting Started 1-19...
Page 45
4263B Resetting the 4263B 1-20 Getting Started...
Page 46
4263B Selecting the Measurement Parameter Primary Secondary Note Getting Started 1-21...
Page 47
4263B Setting the Test Signal Frequency Selecting the Measurement Range Hold Range Auto Range mode Hold Range Hold Range mode 1-22 Getting Started...
Page 48
4263B Setting the Test Signal Level Matching the Cable Length Getting Started 1-23...
Page 49
4263B Performing the OPEN Correction 1-24 Getting Started...
Page 50
4263B Performing the SHORT Correction Getting Started 1-25...
Page 51
4263B Performing the LOAD Correction 1-26 Getting Started...
4263B If You Have a Problem If the Display is Blank and the 4263B Appears Dead If an Error Message is Displayed If the 4263B does not Accept Any Key Input Key Lock 2-14 Operating the 4263B...
Page 68
Function Reference and Technical Information Function Reference and Technical Information 3-1...
4263B Front Panel Figure 3-1. Front Panel Note Display Meas Time Trigger Hold Range Load On Comprtr On Cont Chk Talk Only Key Lock Shift 3-2 Function Reference and Technical Information...
4263B LINE Switch Note Note Chassis Terminal UNKNOWN Terminals Caution Function Reference and Technical Information 3-3...
Page 71
4263B DC Bias Key Note Measurement Parameter Key Primary Secondary 3-4 Function Reference and Technical Information...
Page 72
4263B Note Deviation (1) Mode Key 1ABS mode M easuredV alue ReferenceV alue 1% mode M easuredV alue ReferenceV alue ReferenceV alue Note Measurement Time Key Average Key Function Reference and Technical Information 3-5...
Page 73
4263B Frequency Key Display Mode Key Data Comprtr Digit Measurement Settings Display Key Level Monitor Key 3-6 Function Reference and Technical Information...
Page 74
4263B Level Key Note DC Bias Setup Key Auto/Hold Range Key Hold Range Function Reference and Technical Information 3-7...
Page 75
4263B Range Setup Key Table 3-1. Measurement Range Selection Range Setup Optimum Measurement Range Measurable Range j j j j < j j j j < j j j j < j j j j <...
4263B Back Space key Minimum Key Maximum Key 3-12 Function Reference and Technical Information...
Page 80
4263B Open Key OpenMeas MeasVal Exit j j g Function Reference and Technical Information 3-13...
Page 81
4263B Short Key ShortMeas MeasVal Exit j j g Note 3-14 Function Reference and Technical Information...
Page 82
4263B Load Key On/O Load On Load On LoadMeas Corval PrmSlct RefEnt MeasVal Exit Exit Function Reference and Technical Information 3-15...
Page 83
4263B Comparator Key Comptr On Destination Condition Note 3-16 Function Reference and Technical Information...
Page 84
4263B Contact Check Key Measurement Contact Check Range Setup Available Range < < < < < < < < < < j j < j j < < < Note Function Reference and Technical Information 3-17...
Page 85
4263B Cable Key Cable Length Reference Plane Available Frequency Range Note Key Lock Key Note 3-18 Function Reference and Technical Information...
Page 86
4263B Reset Key Item Reset key Stored in Function Reference and Technical Information 3-19...
Page 87
4263B Conguration Key Note Item Result Error Code 3-20 Function Reference and Technical Information...
4263B Rear Panel Figure 3-2. Rear Panel External Trigger Terminal Figure 3-3. Required External Trigger Pulse Specication Function Reference and Technical Information 3-21...
Page 89
4263B External DC Bias Terminal Caution LINE Fuse Holder LINE Voltage Selector Table 3-3. Line Voltage selection Voltage Selector Line Voltage Required Fuse Serial Number Plate Power Cord Receptacle Power Code 3-22 Function Reference and Technical Information...
4263B Handler Interface Specication Note Figure 3-4. Pin Assignment of Handler Interface Connector Function Reference and Technical Information 3-23...
Page 91
4263B Table 3-4. Pin Assignment of Handler Interface Connector Pin No. Signal Name Description E11 E12 E13 E14 E15 E20 E 313 3-24 Function Reference and Technical Information...
Page 92
4263B Figure 3-5. Timing Diagram Note Function Reference and Technical Information 3-25...
4263B Technical Information Overall Impedance Measurement Theory Figure 3-6. Simplied Model of Impedance Measurement Figure 3-7. Vector Representation of Impedance Function Reference and Technical Information 3-27...
Page 95
4263B Note Figure 3-8. Relationship Between Impedance and Admittance Figure 3-9. Vector Representation of Admittance 3-28 Function Reference and Technical Information...
Page 96
4263B Note Figure 3-10. Relationship between Measurement Parameters Function Reference and Technical Information 3-29...
Page 97
4263B Transformer Parameters Measurement Note Figure 3-11. Basic Transformer Measurement Setup 3-30 Function Reference and Technical Information...
Page 98
4263B Warning While H terminal of the 4263B is connected to a terminal of the transformer, high-voltage can be induced at the other terminals. For safe operation, when connecting or disconnecting a transformer, connect the transformer leads in the following order:...
Page 99
4263B Test Current Level Measurement Range Setting Figure 3-12. Test Signal for DCR Measurement 3-32 Function Reference and Technical Information...
Page 100
4263B DC Resistance Value < R DUT Test Current Transient Trigger Delay Delay Time in DC Resistance Setting (Td Measurement (Td < Function Reference and Technical Information 3-33...
Page 101
4263B Figure 3-13. Test Signal Transient in DC Resistance Measurement 3-34 Function Reference and Technical Information...
Page 102
Remote Operation (To Control from a Computer) Note BASIC Programming Techniques BASIC Language Reference Beginner's Guide to SCPI BASIC Interfacing Techniques Tutorial Description of the General Purpose Interface Bus Condensed Description of the General Purpose Interface Bus Remote Operation (To Control from a Computer) 4-1...
4263B Remote Operation Step 1; Resetting Step 1; Initiating trigger system Step 1; Impedance measurement Step 1; Primary Parameter: CS Step 1; Secondary Parameter: D Step 1; Test Signal Frequency: 100 Hz Step 2; Trigger Source: Bus Step 2; Triggering Step 3;...
Page 106
4263B To Set Up the 4263B To Reset the 4263B Note To Set the Power Line Frequency To Match Cable Length of the Test Fixture To Select the Measurement Parameter Note Remote Operation (To Control from a Computer) 4-5...
Page 107
4263B 4-6 Remote Operation (To Control from a Computer)
Page 108
4263B To Select the Test Signal Frequency To Select the Test Signal Level To Select Measurement Range Remote Operation (To Control from a Computer) 4-7...
Page 109
4263B To Apply a DC Bias To Perform Correction Note 4-8 Remote Operation (To Control from a Computer)
Page 110
4263B To Select Measurement Time Mode Remote Operation (To Control from a Computer) 4-9...
Page 111
4263B To Set the Averaging Rate To Set Trigger Delay Time To Set Beeper Mode To Lock Out the Front Panel Keys To Check Contact Integrity at the Test Fixture To Use the Comparator Function 4-10 Remote Operation (To Control from a Computer)
Page 112
4263B f j g To Display a Deviation Measurement f j g To Wait Until Previously Sent Commands are Completed Remote Operation (To Control from a Computer) 4-11...
Page 113
4263B To Get the Current Instrument Settings To Save and Recall Instrument Settings 4-12 Remote Operation (To Control from a Computer)
Page 114
4263B To Trigger a Measurement Follow the procedure below to perform successive measurements automatically (initial setup). :TRIG:SOUR :INIT:CONT Two methods to perform a measurement at your desired time: Triggering the instrument at your desired time :TRIG:SOUR :INIT:CONT Command Query response...
4263B Waiting For Completion Of Measurement (detecting completion of measurement) *SRE :STAT:OPER:ENAB Figure 4-2. SRQ generation sequence (when measurement nishes) 4-14 Remote Operation (To Control from a Computer)
4263B Reading Out Measured Result Available trigger mode Readout procedure *TRG *TRG :FETC? :FETC? Note *TRG 4-16 Remote Operation (To Control from a Computer)
4263B Reading out measured result using *TRG command *TRG :TRIG:SOUR *TRG *TRG Remote Operation (To Control from a Computer) 4-17...
Page 119
4263B Figure 4-4. Reading out the measured result in ASCII transfer format by using the *TRG command 4-18 Remote Operation (To Control from a Computer)
Page 120
4263B Note Remote Operation (To Control from a Computer) 4-19...
Page 121
4263B Figure 4-5. Reading out the measured result in binary transfer format using *TRG command 4-20 Remote Operation (To Control from a Computer)
4263B Reading out measured result using :FETC? command :FETC? Note :TRIG :FETC? :FETC? :FETC? Remote Operation (To Control from a Computer) 4-21...
Page 123
4263B Figure 4-6. Reading out the measured result in ASCII transfer format using the :FETC? command 4-22 Remote Operation (To Control from a Computer)
Page 124
4263B :FETC? Note Remote Operation (To Control from a Computer) 4-23...
Page 125
4263B Figure 4-7. Reading out measured result in binary transfer format using :FETC? command 4-24 Remote Operation (To Control from a Computer)
Page 126
4263B To Retrieve Data Eciently To Use a Data Buer Remote Operation (To Control from a Computer) 4-25...
4263B Other Features To Test the 4263B To Report the Instrument's Status Enable Measuring bit of Operation Status Register Enable Operation Status Register Summary bit Wait until the Operation Status Register Summary bit is set Clears status byte register Sets Command Error Bit and Execution Error Bit...
Page 128
4263B Clear the SRQ BIt Asks contents of the Standard Event Status Register Asks to output error number and message Remote Operation (To Control from a Computer) 4-27...
Page 129
4263B If You Have a Problem If the 4263B Hangs Up When You Send the :ABORt Command 4-28 Remote Operation (To Control from a Computer)
4263B Parameter Types numeric value < > numeric value < > numeric value < > < > < > sensor function data handle < > < > sensor function < > using single quote using double quote Units 5-6 GPIB Reference...
Page 147
4263B , < > :DATA:FEED BUF1 BUF2 data handle data handle < > :DATA:FEED:CONTrol BUF1 BUF2 ALWays NEVer :DATA:POINts BUF1 BUF2 , < > numeric value numeric value < > numeric < > 5-18 GPIB Reference...
Page 148
4263B DISPlay Subsystem COMMAND PARAMETER < > f j j g f j g f j j j j j g :DISPlay[:WINDow][:STATe] :DISPlay[:WINDow]:TEXT1:DIGit :DISPlay[:WINDow]:TEXT1:PAGE GPIB Reference 5-19...
Page 166
4263B numeric value < > numeric value SAV < > numeric value numeric value < > numeric value SRE < > numeric value numeric value < > numeric value SRE? < > STB? < > TST? Test Item Error Code <...
4263B Parallel/Series Circuit Mode Table 7-1. Parallel/Series Circuit Model Circuit Model Measurement Denition of D, Q, and G Function Impedance Measurement Basics 7-3...
Page 193
4263B Selecting Circuit Model for Capacitance Measurement Small Capacitance Values Large Capacitance Values Figure 7-2. Capacitance Circuit Model Selection 7-4 Impedance Measurement Basics...
Page 194
4263B Selecting Circuit Model for Inductance Measurement Small Inductance Values Large Inductance Values Figure 7-3. Inductance Circuit Model Selection Impedance Measurement Basics 7-5...
Page 203
4263B Standard for the LOAD Correction Using a Standard Supplied by a Component Manufacturer Using Your Own Standard Selecting the LOAD standard. Measuring the LOAD reference value. 7-14 Impedance Measurement Basics...
4263B Supplemental Performance Characteristics < Test Signal Level < < < < < < < < < Specications 8-11...
Page 215
4263B Parameter Measurement Range AE L AE L =L x L x =E Cable Test Signal Frequency Length 100/120 Hz 1 kHz 10 kHz 20 kHz 100 kHz Test Signal Frequency 100/120 Hz 1 kHz 10 kHz 20 kHz 100 kHz...
Page 216
4263B AE R AE R D =R x Cable Length D" G=L x I=L x Measurement Test Signal Frequency Time Mode 100/120 Hz 1 kHz 10 kHz 20 kHz 100 kHz Cable Length Test Signal Frequency 100/120 Hz 1 kHz 10 kHz 20 kHz 100 kHz...
Page 217
4263B Measurement Test Signal Frequency Time Mode 100/120 Hz 1 kHz 10 kHz 20 kHz 100 kHz Test Signal Level < < < < 8-14 Specications...
Page 218
4263B Table 8-4. Measurement Time (DC Bias: OFF) Measurement Analog Digital Tzm1 Time Mode Measurement Computation (= Analog Meas. + Dig. Comput.) Table 8-5. Measurement Time (DC Bias: ON) Measurement Test Signal Test Signal Level Tzm2 Time Mode Frequency Specications 8-15...
Page 219
4263B < Table 8-6. Additional Measurement Time for Rdc Measurement Measurement Tdcr Time Mode Table 8-7. Additional Measurement Time for N and M Measurement Measurement Time Mode approx. 10 N approx. 10 Measurement Maximum DC Range Bias Current 8-16 Specications...
Page 220
4263B < < < Figure 8-2. Maximum Capacitor Voltage Caution Specications 8-17...
4263B Test Signal Frequency Accuracy Test Specication Note Test Equipment Description Recommended Model Procedure Figure 9-1. Test Signal Frequency Accuracy Test Setup Maintenance 9-5...
Page 227
4263B Table 9-2. Frequency Accuracy Test Settings Test Signal Frequency 9-6 Maintenance...
Page 228
4263B Test Signal Level Accuracy Test Specication Test Equipment Description Recommended Model Procedure Figure 9-2. Test Signal Level Accuracy Test Setup Shift 5 495 495 495 475 495 495 495 Enter Maintenance 9-7...
Page 229
4263B Table 9-3. Level Accuracy Test Settings Test Signal Test Signal Level Frequency 9-8 Maintenance...
Page 230
4263B DC Bias Level Accuracy Test Specication Test Equipment Description Recommended Model Procedure Description Recommended Model Figure 9-3. DC Bias Level Accuracy Test Setup Maintenance 9-9...
Page 231
4263B Figure 9-4. DC Bias Level Accuracy Test Setup Without The Interface Box Table 9-4. Bias Level Accuracy Test Settings DC Bias Level 9-10 Maintenance...
Page 232
4263B 0 m Impedance Measurement Accuracy Test Specication Test Equipment Description Recommended Model Procedure 0 m Capacitance Measurement Accuracy Test (Meas. Time Mode: LONG). Figure 9-5. 0 m Impedance Measurement Accuracy Test Setup Maintenance 9-11...
Page 233
4263B Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: 9-12 Maintenance...
Page 234
4263B Table 9-5. 0 m Capacitance Measurement Test (LONG) Settings Standard Test Signal Frequency 0 m Capacitance Measurement Accuracy Test (Meas. Time Mode: MED). Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Maintenance 9-13...
Page 235
4263B Table 9-6. 0 m Capacitance Measurement Test (MED) Settings Standard Test Signal Frequency 0 m Capacitance Measurement Accuracy Test (Meas. Time Mode: SHORT). Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Table 9-7. 0 m Capacitance Measurement Test (SHORT) Settings...
Page 236
4263B Table 9-8. 0 m Capacitance Measurement Test (DC Bias) Setting Standard Test Signal Frequency 0 m Resistance Measurement Accuracy Test (Meas. Time Mode: LONG). Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Maintenance 9-15...
Page 237
4263B Table 9-9. 0 m Resistance Measurement Test (LONG) Settings Standard Test Signal Frequency 0 m Resistance Measurement Accuracy Test (Meas. Time Mode: MED). Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Table 9-10. 0 m Resistance Measurement Test (MED) Settings...
Page 238
4263B Table 9-11. 0 m Resistance Measurement Test (SHORT) Settings Standard Test Signal Frequency 0 m DC Resistance Measurement Accuracy Test (Opt. 001 Only). Measurement Parameter: Measurement Time Mode: Test Signal Level: Trigger Mode: Maintenance 9-17...
Page 239
4263B 1 m Impedance Measurement Accuracy Test Specication Test Equipment Description Recommended Model Procedure 1 m Capacitance Measurement Accuracy Test. 9-18 Maintenance...
Page 240
4263B Figure 9-6. 1 m Impedance Measurement Accuracy Test Setup Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Maintenance 9-19...
Page 241
4263B Table 9-12. 1 m Capacitance Measurement Test Settings Standard Test Signal Frequency 1 m Resistance Measurement Accuracy Test. Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Table 9-13. 1 m Resistance Measurement Test Settings...
Page 242
4263B 1 m DC Resistance Measurement Accuracy Test (Opt. 001 Only). Measurement Parameter: Measurement Time Mode: Test Signal Level: Trigger Mode: Maintenance 9-21...
Page 243
4263B 2 m Impedance Measurement Accuracy Test Specication Test Equipment Description Recommended Model Procedure 2 m Capacitance Measurement Accuracy Test. 9-22 Maintenance...
Page 244
4263B Figure 9-7. 2 m Impedance Measurement Accuracy Test Setup Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Maintenance 9-23...
Page 245
4263B Table 9-14. 2 m Capacitance Measurement Test Settings Standard Test Signal Frequency 2 m Resistance Measurement Accuracy Test. Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Table 9-15. 2 m Resistance Measurement Test Settings...
Page 246
4263B 2 m DC Resistance Measurement Accuracy Test (Opt. 001 Only). Measurement Parameter: Measurement Time Mode: Test Signal Level: Trigger Mode: Maintenance 9-25...
Page 247
4263B 4 m Impedance Measurement Accuracy Test Specication Test Equipment Description Recommended Model Procedure 4 m Capacitance Measurement Accuracy Test. 9-26 Maintenance...
Page 248
4263B Figure 9-8. 4 m Impedance Measurement Accuracy Test Setup Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Maintenance 9-27...
Page 249
4263B Table 9-16. 4 m Capacitance Measurement Test Settings Standard Test Signal Frequency 4 m Resistance Measurement Accuracy Test. Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Table 9-17. 4 m Resistance Measurement Test Settings...
Page 250
4263B 4 m DC Resistance Measurement Accuracy Test (Opt. 001 Only). Measurement Parameter: Measurement Time Mode: Test Signal Level: Trigger Mode: Maintenance 9-29...
Page 251
4263B Calculation Sheet Test Signal Frequency Accuracy Test Test Signal Counter Reading Test Result Frequency Equation Test Signal Level Accuracy Test Test Signal Test Signal Multimeter Reading Test Result Level Frequency Equation DC Bias Level Accuracy Test DC Bias Multimeter Reading...
Page 252
4263B Standards' Calibration Values Standard Frequency Parameter Calibration Value Reference Designation Maintenance 9-31...
Page 253
4263B 0 m Impedance Measurement Accuracy Test 0 m Capacitance Measurement Accuracy Test (Meas. Time Mode: LONG) Standard Test Signal Parameter 4263B Reading Test Result Frequency Measured Equation 9-32 Maintenance...
Page 254
4263B 0 m Capacitance Measurement Accuracy Test (Meas. Time Mode: LONG) Standard Test Signal Parameter 4263B Reading Test Result Frequency Measured Equation 0 m Capacitance Measurement Accuracy Test (Meas. Time Mode: MED) Standard Test Signal Parameter 4263B Reading Test Result...
Page 255
4263B 0 m Resistance Measurement Accuracy Test (Meas. Time Mode: MED) Standard Test Signal Parameter 4263B Reading Test Result Frequency Measured Equation 0 m Resistance Measurement Accuracy Test (Meas. Time Mode: SHORT) Standard Test Signal Parameter 4263B Reading Test Result...
Page 256
4263B 1 m Impedance Measurement Accuracy Test 1 m Capacitance Measurement Accuracy Test Standard Test Signal Parameter 4263B Reading Test Result Frequency Measured Equation 1 m Resistance Measurement Accuracy Test Standard Test Signal Parameter 4263B Reading Test Result Frequency Measured...
Page 257
4263B 2 m Impedance Measurement Accuracy Test 2 m Capacitance Measurement Accuracy Test Standard Test Signal Parameter 4263B Reading Test Result Frequency Measured Equation 2 m Resistance Measurement Accuracy Test Standard Test Signal Parameter 4263B Reading Test Result Frequency Measured...
Page 258
4263B 4 m Impedance Measurement Accuracy Test 4 m Capacitance Measurement Accuracy Test Standard Test Signal Parameter 4263B Reading Test Result Frequency Measured Equation 4 m Resistance Measurement Accuracy Test Standard Test Signal Parameter 4263B Reading Test Result Frequency Measured...
4263B Performance Test Record Test Signal Frequency Accuracy Test Test Signal Test Limits Test Result Measurement Frequency Uncertainty Test Signal Level Accuracy Test Test Signal Test Signal Test Limits Test Result Measurement Level Frequency Uncertainty 9-38 Maintenance...
Page 260
4263B DC Bias Level Accuracy Test DC Bias Test Limits Test Result Measurement Level Uncertainty Record-1 Maintenance 9-39...
Page 261
4263B 0 m Impedance Measurement Accuracy Test 0 m Capacitance Measurement Accuracy Test (Meas. Time Mode: LONG) 1 of 2 Standard Test Signal Parameter Test Limits Test Result Measurement Frequency Measured Uncertainty 9-40 Maintenance Record-2...
Page 262
4263B 0 m Capacitance Measurement Accuracy Test (Meas. Time Mode: LONG) 2 of 2 Standard Test Signal Parameter Test Limits Test Result Measurement Frequency Measured Uncertainty 0 m Capacitance Measurement Accuracy Test (Meas. Time Mode: MED) Standard Test Signal Parameter...
Page 263
4263B 0 m Resistance Measurement Accuracy Test (Meas. Time Mode: LONG) Standard Test Signal Parameter Test Limits Test Result Measurement Frequency Measured Uncertainty 0 m Resistance Measurement Accuracy Test (Meas. Time Mode: MED) Standard Test Signal Parameter Test Limits Test Result...
Page 264
4263B 1 m Impedance Measurement Accuracy Test 1 m Capacitance Measurement Accuracy Test Standard Test Signal Parameter Test Limits Test Result Measurement Frequency Measured Uncertainty 1 m Resistance Measurement Accuracy Test Standard Test Signal Parameter Test Limits Test Result Measurement...
Page 265
4263B 2 m Impedance Measurement Accuracy Test 2 m Capacitance Measurement Accuracy Test Standard Test Signal Parameter Test Limits Test Result Measurement Frequency Measured Uncertainty 2 m Resistance Measurement Accuracy Test Standard Test Signal Parameter Test Limits Test Result Measurement...
Page 266
4263B 4 m Impedance Measurement Accuracy Test 4 m Capacitance Measurement Accuracy Test Standard Test Signal Parameter Test Limits Test Result Measurement Frequency Measured Uncertainty 4 m Resistance Measurement Accuracy Test Standard Test Signal Parameter Test Limits Test Result Measurement...
4263B Functional Tests Introduction Test Equipment 9-46 Maintenance...
Page 268
4263B Transformer Measurement Functional Test (Opt. 001 Only) Test Equipment Description Recommended Model Procedure Figure 9-9. Transformer Measurement Functional Test Setup Measurement Parameter: Measurement Time Mode: Test Signal Level: Test Signal Frequency: Trigger Mode: Maintenance 9-47...
Page 269
4263B Table 9-18. Transformer Measurement Test Limits Switch Frequency Minimum Maximum Setting Setting Limit Limit 9-48 Maintenance...
Page 270
4263B Handler Interface Functional Test Test Equipment Description Recommended Model Procedure Initial Setup. Figure 9-10. Handler Interface Functional Test Setup Key Lock Function Test. External Trigger Function Test. Maintenance 9-49...
Manual Changes Introduction Manual Changes MANUAL CHANGES Table A-1. Manual Changes by Serial Number Serial Prex Make Manual Changes or Number Manual Changes A-1...
Handler Interface Installation Introduction Electrical Characteristics Output Signals Table B-1. Handler Output Electrical Characteristics Output Signals Voltage Output Rating Maximum External Voltage / Current Circuit Common High Comparison Signals Control Signals Handler Interface Installation B-1...
4263B Input Signals Table B-2. Handler Interface Input Electrical Characteristics Signal Input Voltage Input Current (Low) Circuit Common High Pull-up Voltage 12 V 15 V Figure B-3. Handler Interface Input Signal Diagram B-4 Handler Interface Installation...
Page 282
Tools and Fasteners Procedure Warning Dangerous energy and voltage levels exist within the 4263B when it is in operation and just after it is powered down. Allow 10 minutes for the 4263B's internal capacitors to discharge before starting to work on it.
Page 285
4263B Table B-3. Pull-up Resistor Location Socket No. Signal Name Signal Type Pull-up Pull-up Resistor Voltage Agilent Part Number Pull-up Pull-up Resistor Voltage Agilent Part Number B-8 Handler Interface Installation...
Page 304
REGIONAL SALES AND SUPPORT OFFICES For more information about Agilent Technologies test and measurement products, applications, services, and for a current sales office listing, visit our web site: http://www.agilent.com/find/tmdir. You can also contact one of the following centers and ask for a test and measurement sales representative.
Page 305
Agilent 4263B LCR Meter Operation Manual Manual Change Agilent Part No. N/A Jun 2009 Change 1 Add TAR in Test Signal Frequency Accuracy Test (Page 9-38) as follows. Test Signal Frequency Accuracy Frequency Limits [Hz] Result [Hz] Uncertainty [Hz] [Hz] ±0.01...
Page 307
Limits Result Uncertainty 17.76 100 mΩ ±0.52 mΩ mΩ ± 0.030 mΩ 16.31 100 mΩ ±0.48 mΩ mΩ ± 0.030 mΩ Note 1: Result = Measurement – Calibrated Value of Standard Measurement: Resistance Cable length: Copyright 2009 Agilent Technologies ○...
Page 308
Status PASS Standard Parameter Limits Result Uncertainty ± 0.039 25.06 100 mΩ ±0.97 mΩ mΩ mΩ 67.56 100 kΩ ±0.87 kΩ mΩ ± 0.013 kΩ Note 1: Result = Measurement – Calibrated Value of Standard Copyright 2009 Agilent Technologies ○...
Page 309
PASS Frequency [Hz] Standard Limits Result Uncertainty ± 0.030 35.88 100 mΩ ±1.05 mΩ mΩ mΩ 26.19 100 kΩ ±0.87 kΩ mΩ ± 0.014 kΩ Note 1: Result = Measurement – Calibrated Value of Standard Copyright 2009 Agilent Technologies ○...
Page 310
Test signal level: Status PASS Standard Parameter Limits Result Uncertainty 38.28 100 mΩ ±1.13 mΩ mΩ ± 0.030mΩ 66.20 100 kΩ ±0.87 kΩ mΩ ± 0.014 kΩ Note 1: Result = Measurement – Calibrated Value of Standard Copyright 2009 Agilent Technologies ○...
Page 311
Status PASS Standard Parameter Limits Result Uncertainty ± 0.030 43.74 100 mΩ ±1.29 mΩ mΩ mΩ 68.26 100 kΩ ±0.87 kΩ kΩ ± 0.013 kΩ Note 1: Result = Measurement – Calibrated Value of Standard Copyright 2009 Agilent Technologies ○...
Page 312
Agilent 4263B LCR Meter Operation Manual Manual Change Agilent Part No. N/A July 2008 Change 1 Change the Measurement Uncertainty value of Test Signal Frequency Accuracy Test (Page 9-38) to the following information. Test Signal Test Limits Test Result Measurement...
Page 314
Measurement Standard Frequency Measured Test Limits Test Result Uncertainty 0.01 μF 100 Hz ± 0.179 nF ± 0.011 nF ±0.0179 ± 0.00072 0.01 μF 100 kHz ± 0.287 nF ± 0.00081 nF ±0.0287 ± 0.00069 Copyright 2007 Agilent Technologies ○...
Page 315
0 m Resistance Measurement Accuracy Test (Meas. Time Mode: SHORT) (Page 9-42) to the following information. Test Signal Parameter Measurement Standard Frequency Measured Test Limits Test Result Uncertainty 100 mohm 100 Hz ±1.10 mohm mohm ± 0.13 mohm Copyright 2007 Agilent Technologies ○...
Page 316
1 m Resistance Measurement Accuracy Test (Page 9-43) to the following information. Test Signal Parameter Measurement Standard Frequency Measured Test Limits Test Result Uncertainty 100 mohm 100 Hz ±0.60 mohm mohm ± 0.030 mohm 100 mohm 1 kHz ±0.60 mohm mohm ± 0.031 mohm Copyright 2007 Agilent Technologies ○...
Page 317
2 m Resistance Measurement Accuracy Test (Page 9-44) to the following information. Test Signal Parameter Measurement Standard Frequency Measured Test Limits Test Result Uncertainty 100 mohm 100 Hz ±0.68 mohm mohm ± 0.030 mohm 100 mohm 1 kHz ±0.72 mohm mohm ± 0.034 mohm Copyright 2007 Agilent Technologies ○...
Page 318
4 m Resistance Measurement Accuracy Test (Page 9-45) to the following information. Test Signal Parameter Measurement Standard Frequency Measured Test Limits Test Result Uncertainty 100 mohm 100 Hz ±0.84 mohm mohm ± 0.030 mohm 100 mohm 1 kHz ±0.96 mohm mohm ± 0.030 mohm Copyright 2007 Agilent Technologies ○...
Page 319
4 m DC Resistance Measurement Accuracy Test (Opt. 001.Only) (Page 9-45) to the following information. Measurement Standard Test Limits Test Result Uncertainty 100 mohm ±1.29 mohm mohm ± 0.030 mohm 100 kohm ±0.87 kohm kohm ± 0.013 kohm Copyright 2007 Agilent Technologies ○...
Page 320
Agilent 4263B LCR Meter Operation Manual Manual Change Agilent Part No. N/A July 2007 Change 1 Add the following steps to the step 2 of DC Bias Level Accuracy Test (page 9-9). 2-a. Set the test signal frequency to 100 kHz using Freq.
Page 322
June 2007 Change 1 Add the following note to the “3-c. Turning On the 4263B and Setting the Line Frequency” (page 1-13). Note In case the setting of the ac line frequency is not match, there’s any possibility the measurement error will rise.
Page 323
マニュアル チェンジ 変更 1 電源投入と電源周波数の設定の手順 3-c(ページ 1-11)に以下の注記を追加して下さい。 注記 AC 電源周波数の設定値が一致していない場合、測定誤差が増大する可能性があります。必ず AC 電源周波数 を正しく設定して下さい。 変更 2 測定確度の条件(ページ 8-3)に以下の条件を追加して下さい。 5. AC 電源周波数が正しく設定されている。 Copyright 2007 Agilent Technologies ○...
When you notice any of the unusual conditions listed below, immediately terminate operation and disconnect the power cable. Contact your local Agilent Technologies sales representative or authorized service company for repair of the instrument. If you continue to operate without repairing the instrument, there is a potential fire or shock hazard for the operator.
Page 330
Do not apply DC voltage or current to the UNKNOWN terminals. Do not apply External DC bias voltage more than +2.5V. Doing so will damage the 4263B. Before you measure a capacitor, be sure the capacitor is fully discharged. 4263B...