Keysight Technologies Option 503 Service Manual
Keysight Technologies Option 503 Service Manual

Keysight Technologies Option 503 Service Manual

Pxa signal analyzer
Table of Contents

Advertisement

Quick Links

Keysight Technologies
N9030A PXA Signal Analyzer
N9030A Option 503 (3 Hz – 3.6 GHz)
N9030A Option 508 (3 Hz – 8.4 GHz)
N9030A Option 513 (3 Hz – 13.6 GHz)
N9030A Option 526 (3 Hz – 26.5 GHz)
N9030A Option 543 (3 Hz – 43 GHz)
N9030A Option 544 (3 Hz – 44 GHz)
N9030A Option 550 (3 Hz – 50 GHz)
Notice: This document contains references to Agilent.
Please note that Agilent's Test and Measurement
business has become Keysight Technologies. For
more information, go to www.keysight.com.
Service Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Option 503 and is the answer not in the manual?

Questions and answers

Summary of Contents for Keysight Technologies Option 503

  • Page 1 Keysight Technologies N9030A PXA Signal Analyzer N9030A Option 503 (3 Hz – 3.6 GHz) N9030A Option 508 (3 Hz – 8.4 GHz) N9030A Option 513 (3 Hz – 13.6 GHz) N9030A Option 526 (3 Hz – 26.5 GHz) N9030A Option 543 (3 Hz – 43 GHz) N9030A Option 544 (3 Hz –...
  • Page 2 DOCUMENT OR ANY provided to the public to use, INFORMATION CONTAINED modify, reproduce, release, HEREIN. SHOULD KEYSIGHT AND perform, display, or disclose © Keysight Technologies, Inc. THE USER HAVE A SEPARATE commercial computer software or 2012-2017 WRITTEN AGREEMENT WITH commercial computer software...
  • Page 3 Where to Find the Latest Information Documentation is updated periodically. For the latest information about this instrument, including firmware upgrades, application information, and product information, click the website link below. http://www.keysight.com/find/n9030a To receive the latest updates by email, subscribe to Keysight Email Updates at the following URL: http://www.keysight.com/find/MyKeysight Information on preventing analyzer damage can be found at: www.keysight.com/find/PreventingInstrumentRepair...
  • Page 5: Table Of Contents

    Contacting Keysight Technologies ........
  • Page 6 Contents PXA Instrument Boot Up Process..............53 Typical instrument boot-up process flow .
  • Page 7 Contents 4. RF Section Troubleshooting (RF/Microwave Analyzers) What You Will Find in This Chapter ............. 147 RF Section Description .
  • Page 8 Contents A2 Analog IF Assembly Theory of Operation ............227 A2 Analog IF Troubleshooting .
  • Page 9 Contents Overview ................292 Troubleshooting software related issues .
  • Page 10 Contents 13. Block Diagrams What You Will Find in This Chapter ............. 331 Block Diagrams.
  • Page 11 Contents Attenuators ................463 Low Band Switch.
  • Page 12 Contents Removal ................516 Replacement .
  • Page 13 Contents Instrument Measurement Application Software ..........601 89601 VSA Software .
  • Page 14 Contents N9030A PXA Signal Analyzer Service Guide...
  • Page 15: Overview

    Before You Start Troubleshooting on page 23 ESD Information on page 25 Service Equipment You Will Need on page 29 Required Test Equipment List on page 32 Contacting Keysight Technologies on page 45 How to Return Your Instrument for Service on page 49...
  • Page 16: Keysight Pxa Signal Analyzer Overview

    Hardware upgrades may require installation of optional hardware, and often require readjustment and verification of the hardware option. Virus Information Keysight Technologies does not load anti-virus software into the signal analyzer. It is the customer’s responsibility to install anti-virus software. N9030A PXA Signal Analyzer Service Guide...
  • Page 17: Instrument Option Descriptions

    Overview Instrument Option Descriptions Instrument Option Descriptions The PXA signal analyzer has a variety of hardware and measurement application options. Several of these options are “standard” so they are automatically installed on all PXA analyzers. All options require license files to be present in instrument memory before the option can be used, or viewed on the Show, System screen.
  • Page 18 Overview Instrument Option Descriptions Option Description Notes 3 Hz to 3.6 GHz frequency range 3 Hz to 8.4 GHz frequency range 3 Hz to 13.6 GHz frequency range 3 Hz to 26.5 GHz frequency range 3 Hz to 43 GHz frequency range 3 Hz to 44 GHz frequency range 3 Hz to 50 GHz frequency range Auxiliary Log Video...
  • Page 19 Overview Instrument Option Descriptions Option Description Notes Preamp, 100 kHz to 13.6 GHz Preamp, 100 kHz to 26.5 GHz Preamplifier, 43 GHz With Option 543 only Preamplifier, 44 GHz With Option 544 only Preamplifier, 50 GHz With Option 550 only RT1 or Real Time Analysis Requires option B1X or B85...
  • Page 20: Signal Analyzer Accessories

    Signal Analyzer Accessories Signal Analyzer Accessories A number of accessories are available from Keysight Technologies to help you configure your analyzer for your specific applications. They can be ordered through your local Keysight Sales and Service Office and are listed below.
  • Page 21: 50 Ohm Load

    Overview Signal Analyzer Accessories 50 Ohm Load The Keysight 909 series loads come in several models and options providing a variety of frequency ranges and VSWRs. Also, they are available in either 50 ohm or 75 Ohm. Some examples include the: 909A: DC to 18 GHz 909C: DC to 2 GHz 909D: DC to 26.5 GHz...
  • Page 22: Broadband Preamplifiers And Power Amplifiers

    Overview Signal Analyzer Accessories Broadband Preamplifiers and Power Amplifiers Preamplifiers and power amplifiers can be used with your spectrum analyzer to enhance measurements of very low-level signals. — The Keysight 8447D preamplifier provides a minimum of 25 dB gain from 100 kHz to 1.3 GHz.
  • Page 23: Before You Start Troubleshooting

    Overview Before You Start Troubleshooting Before You Start Troubleshooting Before troubleshooting, complete the following tasks: — Familiarize yourself with the safety symbols marked on the instrument and read the general safety considerations in the front of this guide. — Read the ESD information below. —...
  • Page 24 Overview Before You Start Troubleshooting Always use the three-prong ac power cord supplied with this product. Failure to ensure adequate earth grounding by not using this cord may cause product damage. This instrument has an autoranging line voltage input; be sure the supply voltage is within the specified range.
  • Page 25: Esd Information

    Overview ESD Information ESD Information Protection from Electrostatic Discharge Electrostatic discharge (ESD) can damage or destroy electronic components. All work on electronic assemblies should be performed at a static-safe workstation. Figure 1-1 shows an example of a static-safe workstation using two types of ESD protection: Conductive table-mat and wrist-strap combination.
  • Page 26: Handling Of Electronic Components And Esd

    Overview ESD Information Handling of Electronic Components and ESD The possibility of unseen damage caused by ESD is present whenever components are transported, stored, or used. The risk of ESD damage can be greatly reduced by paying close attention to how all components are handled. —...
  • Page 27: Instrument Maintenance

    Overview Instrument Maintenance Instrument Maintenance Cleaning the Instrument To prevent electrical shock, disconnect the signal analyzer from mains before cleaning. Use a dry cloth or one slightly dampened with water to clean the external case parts. Do not attempt to clean internally.
  • Page 28: Battery Information

    The Keysight part number is 1420-0356 (CR2032). The manufacturer’s part number is CR2032. You can return the battery to your nearest Keysight Technologies Sales and Service office for disposal, if required. Refer to “Contacting Keysight Technologies” on page 45 for a list of Keysight Technologies Sales and Service offices.
  • Page 29: Service Equipment You Will Need

    Overview Service Equipment You Will Need Service Equipment You Will Need There are certain things that will be required to troubleshoot, adjust, and test the PXA Signal Analyzer. They include the following: — Calibration Application Software — Front End Controller Troubleshooting Kit —...
  • Page 30: Front End Controller Troubleshooting Kit

    Overview Service Equipment You Will Need Front End Controller Troubleshooting Kit The Front End Troubleshooting kit contains a PC board, required cables, and installation instructions to verify the switch control logic from the A15 Front End Control board to the lower level front end components is correct. Oftentimes when troubleshooting an RF front end problem, the logic needs to be verified before one of the front end components is changed.
  • Page 31: Usb Keyboard And Mouse

    Overview Service Equipment You Will Need USB Keyboard and Mouse A USB keyboard and mouse will be needed to accomplish many of the different troubleshooting tasks, as well as updating the instrument software. Any standard USB keyboard and mouse should work. USB Storage Device The main reason why a USB storage device will be needed is to download instrument software and backup calibration data when the hard drive in an...
  • Page 32: Required Test Equipment List

    Overview Service Equipment You Will Need Required Test Equipment List The following table identifies the equipment recommended for troubleshooting, adjusting, and verifying the performance of the instrument. Only the recommended and alternate equipment is compatible with the performance verification testing. Some tests can use various models of a particular equipment type.
  • Page 33 Overview Service Equipment You Will Need Table 1-1 Required Test Equipment Instrument Critical Specifications Recommended Al ternative Keysight Model Keysight Model Number or Vendor Number Model Number Microwave Signal Frequency: 10 MHz to 26.5 GHz E8257D 83630A/B Generator #2 Frequency Resolution: 1 Hz (Option 1EA/1EU) (Option 008), (only required for Third...
  • Page 34 Overview Service Equipment You Will Need Table 1-1 Required Test Equipment Instrument Critical Specifications Recommended Al ternative Keysight Model Keysight Model Number or Vendor Number Model Number Function Generator Frequency: 3 Hz to 300 kHz 33250A 33120A A, P Amplitude Resolution: 0.1 mv (required for Channel (Option 001) Harmonic Distortion: −35 dBc...
  • Page 35 Overview Service Equipment You Will Need Table 1-1 Required Test Equipment Instrument Critical Specifications Recommended Al ternative Keysight Model Keysight Model Number or Vendor Number Model Number Microwave Power Sensor Frequency Range: 50 MHz to 26.5 GHz A, P N8485A N8485A CFT (2 required) Amplitude Range: −30 to +20 dB...
  • Page 36 Overview Service Equipment You Will Need Table 1-1 Required Test Equipment Instrument Critical Specifications Recommended Al ternative Keysight Model Keysight Model Number or Vendor Number Model Number Low Power Microwave Frequency Range: 50 MHz to 26.5 GHz A, P 8485D Power Sensor Amplitude Range: −70 to +20 dBm (2 required)
  • Page 37 VSWR: at 50 MHz: ≤ 1.05:1 (For use with Low Power Sensors) Terminations Type-N (m) Frequency: 10 kHz to 18 GHz 909A P, T (for Option 503, 508, 513) VSWR: ≤ 1.05:1 (Option 012) 2.4 mm (f) 50 Ω 85138B (for Options > 543) Frequency: 10 kHz to 50 GHz 3.5 mm (f)
  • Page 38 Overview Service Equipment You Will Need Table 1-1 Required Test Equipment Instrument Critical Specifications Recommended Al ternative Keysight Model Keysight Model Number or Vendor Number Model Number Miscellaneous Devices RF Power Splitter Frequency: 9 kHz to 3.6 GHz 11667A A, P VSWR: ≤...
  • Page 39 Overview Service Equipment You Will Need Table 1-1 Required Test Equipment Instrument Critical Specifications Recommended Al ternative Keysight Model Keysight Model Number or Vendor Number Model Number Cables 3.5 mm (m) to 3.5 mm (m) Frequency: DC to 26.5 GHz 11500E 8120-4921 A, P...
  • Page 40 Overview Service Equipment You Will Need Table 1-1 Required Test Equipment Instrument Critical Specifications Recommended Al ternative Keysight Model Keysight Model Number or Vendor Number Model Number 4.4 GHz Low Pass Cutoff frequency: 4.4 GHz K + L 9135-0005 (2 Required) Rejection at >...
  • Page 41 Overview Service Equipment You Will Need Table 1-1 Required Test Equipment Instrument Critical Specifications Recommended Al ternative Keysight Model Keysight Model Number or Vendor Number Model Number 3.5 mm (m) to 3.5 mm (m) Frequency: DC to 26.5 GHz 83059A 1250-1748 (2 Required) VSWR: ≤...
  • Page 42 The step attenuator combination should have each attenuator setting characterized by a metrology lab at 50 MHz. This characterization can be ordered through Keysight Technologies as an Option H50 Calibration. The following tables show which sections of the 10 dB and 1 dB step attenuators are utilized for each attenuator setting.
  • Page 43 Overview Service Equipment You Will Need The interconnect cable should NEVER be disconnected once the loss characterization is performed. Table 1-2 1 dB Step Attenuator Nominal Attenuation Attenuator Section Recommended Uncertainty (dB) (dB) (1 dB) (2 dB) (4 dB) (4 dB) 0 (Reference) <...
  • Page 44: After An Instrument Repair

    Overview After an Instrument Repair After an Instrument Repair If any instrument assemblies have been repaired or replaced, perform the related adjustments and performance verification tests. These tests are done using the N7814A Keysight X-Series Signal Analyzer Calibration Application Software. Refer to Chapter 17, “Post-Repair Procedures”...
  • Page 45: Contacting Keysight Technologies

    Overview Contacting Keysight Technologies Contacting Keysight Technologies If you have a problem with your instrument, see Chapter 2, “Boot Up and Initialization Troubleshooting”. This section contains a checklist that will help identify some of the most common problems. There is also support on the world-wide web. The address is: http://www.keysight.com/find/pxa_support...
  • Page 46 Overview Contacting Keysight Technologies Table 1-4 Contacting Keysight www.keysight.com/find/contactus Online assistance: Americas Country Phone Number Canada (877) 894 4414 Brazil 55 11 3351 7010 Mexico 001 800 254 2440 United States 1 800 829-4444 Asia Pacific Country Phone Number Australia...
  • Page 47 Overview Contacting Keysight Technologies Europe and Middle Country Phone Number Luxembourg +32 800 58580 Netherlands 0800 0233200 Russia 8800 5009286 Spain 0800 000154 Sweden 0200 882255 Switzerland 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) United Kingdom...
  • Page 48: Instrument Serial Numbers

    Overview Contacting Keysight Technologies Instrument Serial Numbers Keysight makes frequent improvements to its products enhancing performance, usability, or reliability. Keysight service personnel have access to complete records of design changes to each type of instrument, based on the instrument’s serial number and option designation.
  • Page 49: How To Return Your Instrument For Service

    Overview How to Return Your Instrument for Service How to Return Your Instrument for Service Service Order Number If an instrument is being returned to Keysight for servicing, the phone numbers are mentioned in Table 1-4, “Contacting Keysight,” on page 46.
  • Page 50: Other Packaging

    Overview How to Return Your Instrument for Service Other Packaging Instrument damage can result from using packaging materials other than those specified. Never use styrene pellets in any shape as packaging materials. They do not adequately cushion the equipment or prevent it from shifting in the carton.
  • Page 51: Boot Up And Initialization Troubleshooting

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide Boot Up and Initialization Troubleshooting What You Will Find in This Chapter This chapter provides information that is useful when starting to troubleshoot a spectrum analyzer. It includes procedures for troubleshooting common failures and provides information on isolating problems in the analyzer.
  • Page 52: Check The Basics

    Boot Up and Initialization Troubleshooting Check the Basics Check the Basics Before calling Keysight Technologies or returning the instrument for service, please make the following checks: 1. Is there power at the power outlet? At the power receptacle on the instrument? 2.
  • Page 53: Pxa Instrument Boot Up Process

    Boot Up and Initialization Troubleshooting PXA Instrument Boot Up Process PXA Instrument Boot Up Process This section describes the N9030A Signal Analyzer boot up process from initial AC power to a normal analyzer sweep. The boot process time from start to finish will take 6 to 8 minutes.
  • Page 54: Typical Instrument Boot-Up Process Flow

    Boot Up and Initialization Troubleshooting PXA Instrument Boot Up Process Typical instrument boot-up process flow 1. Plug in the AC power cord from a known good AC power source into the rear panel of the analyzer. 2. The yellow standby LED illuminates on the analyzer front panel to the left-hand side of the On/Off button.
  • Page 55 Operating” section in this chapter. 5. The Keysight Technologies splash screen is displayed in white font on a dark background for ~5-10 seconds after the analyzer is turned on. If the Keysight Technologies logo is not displayed refer to the “No Keysight...
  • Page 56 Boot Up and Initialization Troubleshooting PXA Instrument Boot Up Process 11.If any of the initial alignments fail, check the alignment history for troubleshooting hints. The instrument alignment history can be found at: E:\AlignDataStorage\AlignmentHistory.txt Look for any failed status for the various internal hardware items listed in this file.
  • Page 57: Potential Problems During Boot Process

    Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Potential Problems During Boot Process This section describes potential problems that may occur if there is an internal hardware issue that prohibits the instrument from completing a full boot up to the spectrum analyzer application.
  • Page 58 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Figure 2-3 A7 Midplane Board +5.1VSB LED Most DC power supplies come from the A6 Power Supply assembly. However, the most convenient measurement location for all the DC supplies is the A7 Midplane. All power supply LED's are accessible once the instrument cover has been removed.
  • Page 59: Green Power On Led Does Not Illuminate

    Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Green Power On LED Does Not Illuminate Control of the green front panel Power On LED comes from the A4 Processor board assembly. This signal is routed through the A7 Midplane board and is then buffered on the A8 Motherboard before being sent to the A1A2 Front Panel Interface board through W1.
  • Page 60 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Figure 2-4 A7 Midplane Board - Test Point 518/POWER_ON_L LED 5. Turn the instrument power on from the front panel On/Off button and view the status of the POWER_ON_L LED, as shown in Figure 2-4.
  • Page 61 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Measure the voltage at Test Point 520 and compare the results to that in Table 2-1. Table 2-1 Test Point 520 Verification Front Panel Switch Most Probably Cause Released Pressed High A4 Processor High...
  • Page 62 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process It should be noted that the FAULT_L status line can also be triggered by an over voltage or an over temperature condition in the A6 Power Supply assembly. Is the FAULT_L LED on? (Test Point 508 at a TTL low level) If not: Replace the A6 Power Supply assembly.
  • Page 63: Fan(S) Are Not Operating

    Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Fan(s) Are Not Operating Control of the instrument fans comes from the A6 Power Supply assembly. This signal is routed from the A6 Power Supply through the A7 Midplane board, where there is a test point and LED to monitor the level, and is then routed to the A8 Motherboard where it is filtered before being sent to the Fans.
  • Page 64 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process 5. Referring to Figure 2-7, verify that the Fan_P Failure LED on the A7 Midplane board is off. Is the Fan_P LED off? If yes: Measure the voltage level at Test Point 522 on the A7 Midplane board.
  • Page 65: No Keysight Splash Screen Displayed

    A8 Motherboard. No Keysight Splash Screen Displayed (Black background with white “Keysight Technologies” text) A problem of not displaying the Keysight splash screen could be caused by many different things. It could be due to a down power supply, a processor hardware problem, an instrument boot-up process error, a display section failure, etc.
  • Page 66 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Are all of the power supply voltages at the proper level? If yes: Proceed to step If not: After verifying that the connections between the A6 Power Supply, the A7 Midplane board, and the A8 Motherboard are all mechanically and electrically secure, replace the A6 Power Supply assembly.
  • Page 67: Instrument Hangs At The Keysight Splash Screen

    Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Instrument Hangs at the Keysight Splash Screen A problem of the instrument hanging at the Keysight splash screen could be caused by many different things. It could be due to a down power supply, a processor hardware problem, an instrument boot-up process error, etc.
  • Page 68: Instrument Cannot Completely Load Or Run The Operating System

    Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Instrument Cannot Completely Load or Run the Operating System A problem of the instrument not loading the operating system can be caused by a few different things. It could be due to a down power supply, a processor hardware problem, an instrument boot-up process error, corrupt disk drive, etc.
  • Page 69: Verify Lcd Backlight Functionality

    Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Verify LCD Backlight Functionality There are two backlights within the LCD assembly, one across the top and one across the bottom. If only one of the backlights has burnt out, the other will still function.
  • Page 70 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process 6. Referring to Figure 2-8, verify that the red +12VD LED is off. Figure 2-8 A7 Midplane Board +12VD LED/Test Point 503 Is the red +12VD backlight supply voltage fault LED off? If yes: Proceed to step...
  • Page 71 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Figure 2-9 A1A2 Front Panel Interface Board LCD Backlight Inverter Control Voltages Table 2-2 Expected Backlight Inverter Control Voltage Levels Signal Expected Vol tage Brightness Control 0 to 3 VDC Inverter Enable >6 VDC Inverter Supply...
  • Page 72: Verify Video Signal Path Integrity

    Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Verify Video Signal Path Integrity The video controller is located on the A4 Processor assembly and is routed to the front panel LCD through a few interconnections. These interconnections are: —...
  • Page 73: Fails An Initial Alignment

    Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Fails an Initial Alignment Troubleshooting Alignment Failures Using the Alignment History Screen At instrument power on, an initial alignment is automatically performed. It is also possible to manually trigger an alignment by pressing System, Alignments, Align Now, All.
  • Page 74 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Table 2-3 Initial Alignments Alignment Description Most Probable Related Hard ware Hard ware Failure Main Loop YTO Pretune DAC A14 Synthesizer A16 Reference board is not providing correct 100 MHz or 4.8 GHz signals.
  • Page 75 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Table 2-3 Initial Alignments Alignment Description Most Probable Related Hard ware Hard ware Failure AIF LC Narrow Prefilter Passband Tuning A2 Analog IF Algorithm Adjusts the LC prefilter centering with the prefilter BW set to about 413 kHz.
  • Page 76 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Table 2-3 Initial Alignments Alignment Description Most Probable Related Hard ware Hard ware Failure AIF Variable Attenuator Algorithm A2 Analog IF Measures the gain in all settings of the A-IF 1 dB step attenuator.
  • Page 77 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Table 2-3 Initial Alignments Alignment Description Most Probable Related Hard ware Hard ware Failure AIF 140 Variable Attenuator Algorithm A25 Wide band A-IF Ref power at atten 12 dB (Option B1X) DIF 40 Variable Attenuator Algorithm A3 Digital IF Ref power at atten 21 dB...
  • Page 78 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Table 2-3 Initial Alignments Alignment Description Most Probable Related Hard ware Hard ware Failure Aif140 Extended Step Cal Ad justment A13 Front End Alignment Algorithm (option B1Y) assembly switched filter might roll off Extends performance from 140 MHZ to too much to 160 MHz BW...
  • Page 79 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Table 2-3 Initial Alignments Alignment Description Most Probable Related Hard ware Hard ware Failure Low Band Preamp Path System Gain Algorithm A13 Front End 50 MHz calibrator on A16 Reference. Aligns low band (3 Hz to 3.6 GHz path) with preamp ON.
  • Page 80 Boot Up and Initialization Troubleshooting Potential Problems During Boot Process Table 2-3 Initial Alignments Alignment Description Most Probable Related Hard ware Hard ware Failure High Band Preselector Bypass Preamp Path A11 Low Band System Gain Algorithm (Option MPB) Switch Preselector Bypass Switch(s) Burst Carrier Trigger Curve Fit Algorithm A2 Analog IF...
  • Page 81: Signal Level Verification

    Boot Up and Initialization Troubleshooting Signal Level Verification Signal Level Verification Signal Level Problem with Input Frequencies < 3.6 GHz Measure the 50 MHz RF calibrator signal level by pressing Input/Output, RF Calibrator, 50 MHz. Now press Freq, 50 MHz, SPAN, 1 MHz, Peak Search. If the analyzer is functioning correctly in low band, the 50 MHz calibrator level should be −25 dBm ±...
  • Page 82: Signal Level Problem With Input Frequencies > 3.6 Ghz

    Boot Up and Initialization Troubleshooting Signal Level Verification Signal Level Problem with Input Frequencies > 3.6 GHz Measure the 4.8 GHz RF calibrator signal level by pressing Input/Output, RF Calibrator, 4.8 GHz. Now press Freq, 4.8 GHz, SPAN, 1 MHz, Peak Search. If the analyzer is functioning correctly in high band, the 4.8 GHz calibrator level should be −28 dBm ±...
  • Page 83: Instrument Messages

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide Instrument Messages Introduction The Error and Status messaging system of the Keysight Signal Analyzer reports events and conditions in a consistent fashion, as well as logging and reporting event history. Event vs. Condition Messages An Event is simply a message indicating that something has happened.
  • Page 84: Event And Condition Categories

    Instrument Messages Introduction Event and Condition Categories The three categories of severity are described below, for both Events and Conditions. Errors Error messages appear when a requested operation has failed. (For example, “Detector not available”, “File not saved”.) Error messages are often generated during remote operation when an invalid programming command has been entered.
  • Page 85: Event Message Format

    Instrument Messages Introduction Advisories Advisory messages tell the front panel user some useful information. (For example, “File saved successfully” or “Measuring the fundamental”.) Advisory messages appear in the Status Panel at the bottom of the display. The message remains until you press a key, or another message is displayed in its place. Advisory messages are not logged in the error queues.
  • Page 86: Event Queues

    Instrument Messages Introduction Figure 3-1 Error Message Example Event Queues There are several different event queues that are viewed/queried and managed separately. Note that Conditions are logged in the queues as pairs of events: a “Detected” event and a corresponding “Cleared” event. System Show Errors, Status Front Panel Status...
  • Page 87 Instrument Messages Introduction Table 3-1 Characteristics of the Event Queues Characteristic Front-Panel Status Front-Panel History Remote Interfaces (GPIB/LAN) Send SCPI query to the desired System Show System Show Press: Press: Viewing Entries interface. Errors Status Errors History SYSTem:ERRor? Press: Press: Send *CLS command to the System Show...
  • Page 88: Advisory Messages

    Instrument Messages Advisory Messages Advisory Messages An advisory is simply a message that lets you know something useful - for example “File saved successfully” or “Measuring fundamental.” Operation completion and running status indications are common types of advisories. Advisories have no number and are not logged in the error queue. Advisories include gray-out “settings conflict”...
  • Page 89 Instrument Messages Advisory Messages Message Description/Correction Information User has canceled the cal either directly or indirectly by changing the Cal Canceled; Calibration setup parameters. The current cal data has been erased. Perform a new data cleared user cal to obtain calibrated results again. When freq points being measured are above 3.6 GHz and a calibration has Cal Invalid: meas freq pt(s) been successfully performed, and the number of points are changed, the...
  • Page 90 Instrument Messages Advisory Messages Message Description/Correction Information The demodulated burst type has not been found in the originally Frequency Hopping enabled, demodulated slot location within the frame. waiting for valid burst The frequency context parameter has been changed either by the user or Frequency menu has changed to the system.
  • Page 91 Instrument Messages Advisory Messages Message Description/Correction Information The setup frequencies break the rules for a downconverter measurement. LO Fixed freq should be The measurement will still run, but check setup frequencies are correct greater than RF Stop freq before continuing. The LO fixed freq should be greater than the RF Stop freq’s for an LSB or DSB (for DSB measurements the setup uses LSB values) downconverter fixed LO setup.
  • Page 92 Instrument Messages Advisory Messages Message Description/Correction Information The Keysight Smart Noise Source has been connected and the application Reading SNS data… is reading the device EEPROM data. Please wait until complete before continuing. A file recall (open/load) was successfully completed. Recalled File <filename>...
  • Page 93 Instrument Messages Advisory Messages Message Description/Correction Information Span is not coupled to RBW when EMI detector is selected The sweep point to span ratio is below the minimum required to ensure the Sweep Points/Span is < bucket ratio is large enough to test DVB-T masks minimum.
  • Page 94: Event Messages

    Instrument Messages Event Messages Event Messages Event messages read out in the MSG area in the bottom left of the display. Event messages and message numbers are defined by the SCPI standard. In the X-Series, sub-messages are often attached to add additional information, to help the user better understand the event being reported.
  • Page 95: 800, Operation Complete Event

    Instrument Messages Event Messages –800, Operation Complete Event Err# Message Verbose/Correction Information –800 The instrument has completed all selected pending operations in Operation complete accordance with the IEEE 488.2, 12.5.2 synchronization protocol. –700, Request Control Event Err# Message Verbose/Correction Information –700 The instrument requested to become the active IEEE 4881 Request control...
  • Page 96: -300 To -399, Device-Specific Errors

    Verbose/Correction Information –300 An instrument error occurred and the exact problem cannot be specifically Device-specific error identified. Report this error to the nearest Keysight Technologies sales or service office. –310 An internal system-type error has occurred. The exact problem cannot be System error;...
  • Page 97 Instrument Messages Event Messages Err# Message Verbose/Correction Information –310 The specified feature will stop working in the specified time due to the System error; No license expiration You will be prompted to save results and exit. license; <feature code> will terminate in <time>...
  • Page 98 –321 An internal operation needed more memory than was available. Report this Out of memory error to the nearest Keysight Technologies sales or service office. –330 A self-test failure occurred. Report this error to the nearest Keysight Self-test failed Technologies sales or service office.
  • Page 99: -221 Settings Conflict Errors

    Instrument Messages Event Messages –221 Settings Conflict Errors This is one of the errors in the standard SCPI error range of –200 to –299. See the table “–200 to –299, Execution Errors” on page 110. The <subtext> part of a Settings Conflict error should be worded so that the text is: “function1”...
  • Page 100 Instrument Messages Event Messages Err# Message Verbose/Correction Information –221 Base Transceiver Station gain correction is not available in Settings conflict; BTS gain some Modes, or in some measurements (for example, the SA is not available in this measurement). Mode –221 You must be in Tracking Source mode to use the Cal Settings conflict;...
  • Page 101 Instrument Messages Event Messages Err# Message Verbose/Correction Information –221 The resulting trace data (from doing a trace math function) Settings conflict; cannot be put into the any of the traces that are being used Destination trace for Trace by the math operation. Math cannot be a trace operand –221...
  • Page 102 Instrument Messages Event Messages Err# Message Verbose/Correction Information –221 When Swept IF Gain is manually set to Low, you cannot set Settings conflict; FFT IF the FFT IF Gain to High because that would make the Gain High not available when Reference Level couplings wrong in FFT mode.
  • Page 103 Instrument Messages Event Messages Err# Message Verbose/Correction Information –221 The gate function cannot be used while you have marker Settings conflict; Gate is count turned on. not available when Marker Count on –221 The sweep time for FFT sweeps is set by the calculations. So Settings conflict;...
  • Page 104 Instrument Messages Event Messages Err# Message Verbose/Correction Information –221 The logarithmic x-axis scales are not available when you Settings conflict; Log Scale have the demod view turned on. Type is not available with Demod View –221 Logarithmic scaling can be used when making a swept SA Settings conflict;...
  • Page 105 Instrument Messages Event Messages Err# Message Verbose/Correction Information –221 These special units only apply when you are doing antenna Settings conflict; Must measurements so you have to have a correction which apply Amplitude Correction includes Antenna Units enabled to make this unit available –221 Optimize Preselector can only be performed on frequencies Settings conflict;...
  • Page 106 Instrument Messages Event Messages Err# Message Verbose/Correction Information –221 SCPI only message. This parameter is only available when Settings conflict; Param the Freq mode is set to Swept. Change the Freq Mode to only available when Swept Frequency Mode is Swept –221 SCPI only message.
  • Page 107 Instrument Messages Event Messages Err# Message Verbose/Correction Information –221 Span Zoom does not work with a time domain x-axis. You Settings conflict; Span Zoom must select a span greater then 0 Hz. is not available in Zero Span –221 The Span Zoom feature cannot be used when the X-axis Settings conflict;...
  • Page 108 Instrument Messages Event Messages Err# Message Verbose/Correction Information –221 The Normalize function works by doing trace manipulation, Settings conflict; Trace so trace math is not available while normalization is running. Math is not available while Normalize is on –221 Since FFT’s do not sweep, you cannot use a Tracking Source Settings conflict;...
  • Page 109 Instrument Messages Event Messages Err# Message Verbose/Correction Information –221 Settings change is not allowed while measurement is Settings conflict;Function running. You must stop the current measurement if you wish not available while to change the settings. measurement is running –221 Settings conflict;function unavailable with this EMC Standard...
  • Page 110: -200 To -299, Execution Errors

    Instrument Messages Event Messages –200 to –299, Execution Errors For –221 error messages, see the previous sections. Note that Execution Errors are divided into subclasses: –21x – Trigger errors –22x – Parameter error –23x – Data corrupt or stale (invalid data) –24x –...
  • Page 111 Instrument Messages Event Messages Err# Message Verbose/Correction Information –200 Algorithm failed to center the preselector. This maybe caused by Execution Error; the signal peak being too low in amplitude. Or it could be from Preselector centering excessive CW input signal, alignment error, or hardware failure. failed –200 The signal that you have selected to track is changing too much...
  • Page 112 Instrument Messages Event Messages Err# Message Verbose/Correction Information –201 The command cannot be executed while the instrument in Local Invalid while in local control. –202 A “return to local” control was forced and some settings were lost Settings lost due to rtl as a result of this.
  • Page 113 Instrument Messages Event Messages Err# Message Verbose/Correction Information –222 When entering values for limit lines, you cannot have more than Data out of range; Two two y-axis (amplitude) values entered for a specific x-axis entries already exist at (frequency) value. this x-axis value.
  • Page 114 Instrument Messages Event Messages Err# Message Verbose/Correction Information –224 You are trying to set some list measurement settings, but the Illegal parameter value; multiple lists that you sent were not all the same length. The Invalid list length number of settings must be consistent from list to list. –224 This error occurs when you try to add an LXI Event that has Illegal parameter value;...
  • Page 115 Instrument Messages Event Messages Err# Message Verbose/Correction Information –230 There is something wrong with the state data in the desired file. Data corrupt or stale; Maybe the file is corrupt, or it is from an instrument/version that is Unable to load state from not recognized by the current instrument.
  • Page 116 Instrument Messages Event Messages Err# Message Verbose/Correction Information –250 The only Correction register that supports Antenna Units is Mass storage error; Can number 1. You have attempted to load an Ampcor file which only load an Antenna Unit contains antenna units into another register into Correction 1 –250 The directory or file cannot be created.
  • Page 117 Instrument Messages Event Messages Err# Message Verbose/Correction Information –250 You have to have a Peak Table on the screen before you can save Mass storage error; Pk it. Turn on the Peak Table and try again. Table must be on to save Pk Table as Meas Results –250 The system cannot read from the specified device.
  • Page 118 Instrument Messages Event Messages Err# Message Verbose/Correction Information –258 A legal command or query could not be executed because the Media protected media was protected. For example, the write-protect was set –260 An error was found with an expression type of data element. The Expression error exact problem cannot be specifically identified.
  • Page 119 Instrument Messages Event Messages Err# Message Verbose/Correction Information –285 Indicates that a syntax error appears in a downloaded program. Program syntax error The syntax used when parsing the downloaded program is device-specific. –286 Program runtime error –290 Memory use errors –291 Out of memory –292...
  • Page 120: -100 To -199, Command Errors

    Instrument Messages Event Messages –100 to –199, Command Errors Err# Message Verbose/Correction Information –100 There is a problem with the command. The exact problem cannot Command error be specifically identified. –101 An invalid character was found in part of the command. Invalid character –102 An unrecognized command or data type was found, for example...
  • Page 121 Instrument Messages Event Messages Err# Message Verbose/Correction Information –124 The mantissa of a decimal-numeric contained more than 255 Too many digits digits, excluding leading zeros. –128 A legal numeric data element was found, but that is not a valid Numeric data not allowed element at this position in the command.
  • Page 122: Error

    Instrument Messages Event Messages Err# Message Verbose/Correction Information –178 A legal expression data was found, but it is not allowed at this Expression data not point in the parsing. allowed –180 A problem was found with a macro element. The exact problem Macro error cannot be specifically identified.
  • Page 123: Condition Messages

    Instrument Messages Condition Messages Condition Messages Condition messages read out in the STATUS message area in the bottom right of the display. Condition messages are classified as either “Errors” or “Warnings.” In the tables in this section, an E in the Error or Warning column means that an error is put up on the front panel and sent out to SCPI when this condition is detected.
  • Page 124 Instrument Messages Condition Messages Err# Bit in Message Error or More Information status Warning register unused unused unused unused unused unused unused unused unused Condition Errors 36 to 64, Calibration Needed or Failed This series of errors corresponds to the bits in the STATus:QUEStionable:CALibration register.
  • Page 125 Instrument Messages Condition Messages Thus, the summary bits cannot be used to determine the current state of a lower level condition bit; only the state and history of the lower level event bits. This register is itself summarized as bit 8 of the STATus:QUEStionable register. See section “Condition Errors 601 to 699, Error Summaries”...
  • Page 126 Instrument Messages Condition Messages Condition Errors 65 to 92, Calibration Needed (Extended) This series of errors corresponds to the bits in the STATus:QUEStionable:CALibration:EXTended:NEEDed sub-register. The second column in the table shows the corresponding bit. An event with the error number shown in the table means the condition has been detected.
  • Page 127 Instrument Messages Condition Messages Condition Errors 67 to 95, Calibration Failure (Extended) This series of errors corresponds to the bits in the STATus:QUEStionable:CALibration:EXTended:FAILure sub-register. The second column in the table shows the corresponding bit. An event with the error number shown in the table means the condition has been detected.
  • Page 128: Condition Errors 101 To 199, Measurement Integrity

    Instrument Messages Condition Messages Condition Errors 101 to 199, Measurement Integrity This series of errors corresponds to the bits in the STATus:QUEStionable:INTegrity register. The second column in the table shows the corresponding bit. An event with the error number shown in the table means the condition has been detected.
  • Page 129 Instrument Messages Condition Messages Err# Bit in Message Error or More Information status Warning register The current measurement does not No Result; Meas invalid with support I/Q input; switch to the RF or I/Q inputs another input or select a different measurement unused status bit...
  • Page 130 Instrument Messages Condition Messages Err# Bit in Message Error or More Information status Warning register Meas Error Memory Error A shortage of free memory related to Memory Error;Shorten capture longer capture intervals has occurred. interval The measurement is aborted and all results return invalid values I/O Error No IP address entered for external...
  • Page 131 Instrument Messages Condition Messages Err# Bit in Message Error or More Information status Warning register The user has manually set the Analog Settings Alert; Analog Out Output under the Input/Output menu to settings conflict a setting that conflicts with the current measurement.
  • Page 132: Condition Errors 201 To 299, Signal Integrity

    Instrument Messages Condition Messages Condition Errors 201 to 299, Signal Integrity This series of errors corresponds to the bits in the STATus:QUEStionable:INTegrity:SIGNal sub-register. The second column in the table shows the corresponding bit. An event with the error number shown in the table means the condition has been detected.
  • Page 133 Instrument Messages Condition Messages Err# Bit in Message Error or More Information Status Warning Register The burst signal cannot be detected because Burst Not Found of inappropriate parameter settings or incorrect signal. An in appropriate parameter setting could cause the signal to be partially, rather than fully, on the display, Burst Search Threshold and/or Burst Search Length may need to be adjusted.
  • Page 134 Instrument Messages Condition Messages Err# Bit in Message Error or More Information Status Warning Register Timing Error The pilot burst used for time reference is not Timing Error:No time active. ref pilot burst In the PSA, this error was reported as one of Carrier(s) incorrect the following error numbers: 10165, 10173, or missing...
  • Page 135 Instrument Messages Condition Messages Err# Bit in Message Error or More Information Status Warning Register This error is normally generated because of Demod Error one of the following reasons: 1. There is no carrier signal. 2. Walsh channels other than the pilot are active.
  • Page 136 Instrument Messages Condition Messages Err# Bit in Message Error or More Information Status Warning Register There is no active slot detected. Demod Error;Not an active slot No sub-frame or only part of one sub-frame is Demod Error;No full detected. subframe found Multiplexed Data Demod Bits are not Demod Error;Muxed generated even though Data channel is...
  • Page 137: Condition Errors 301 To 399, Uncalibrated Integrity

    Instrument Messages Condition Messages Condition Errors 301 to 399, Uncalibrated Integrity This series of errors corresponds to the bits in the STATus:QUEStionable:INTegrity:UNCalibrated sub-register. The second column in the table shows the corresponding bit. An event with the error number shown in the table means the condition has been detected.
  • Page 138 Instrument Messages Condition Messages Err# Status Message Error or Verbose/Correction Information Register Warning The existing user cal has been invalidated User Cal; Cal invalidated because of one of the following reasons: Frequency: Setting the frequency outside the current valid user cal set (for example: If the current sweep range is 2 to 3GHz, then setting the start frequency to 1.9 GHz will invalidate the current user...
  • Page 139 Instrument Messages Condition Messages Err# Status Message Error or Verbose/Correction Information Register Warning The existing user cal has been invalidated User Cal; Freq outside cal because the current measurement range frequencies lie partially or wholly outside the range of frequencies used for user-cal.
  • Page 140 Instrument Messages Condition Messages Err# Status Message Error or Verbose/Correction Information Register Warning unused N9030A PXA Signal Analyzer Service Guide...
  • Page 141: Condition Errors 401 To 499, Power

    Instrument Messages Condition Messages Condition Errors 401 to 499, Power This series of errors corresponds to the bits in the STATus:QUEStionable:POWer register. The second column in the table shows the corresponding bit. An event with the error number shown in the table means the condition has been detected.
  • Page 142: Condition Errors 501 To 599, Frequency

    Instrument Messages Condition Messages Condition Errors 501 to 599, Frequency This series of errors corresponds to the bits in the STATus:QUEStionable:FREQuencyr register. The second column in the table shows the corresponding bit. An event with the error number shown in the table means the condition has been detected.
  • Page 143: Condition Errors 601 To 699, Error Summaries

    Instrument Messages Condition Messages Condition Errors 601 to 699, Error Summaries This series of errors corresponds to the bits in the STATus:QUEStionable register, read with a STATus:QUEStionable? event query or a STATus:QUEStionable:CONDition? query. The second column in the table shows the corresponding bit in the status register.
  • Page 144 Instrument Messages Condition Messages Err# Bit in Message Error or More Information status Warning register status bit This bit is the summary bit for the Calibration only STATus:QUEStionable:CALibration sub-register. status bit This bit is the summary bit for the Integrity only STATus:QUEStionable:INTegrity sub-register.
  • Page 145: Condition Errors 701 To 799, Operation

    Instrument Messages Condition Messages Condition Errors 701 to 799, Operation This series of errors corresponds to the bits in the STATus:OPERation register, read with a STATus:OPERation? event query or a STATus:OPERation:CONDition? query. An event with the error number shown in the table means the condition has been detected.
  • Page 146: Condition Errors 801 To 899, Temperature

    Instrument Messages Condition Messages Condition Errors 801 to 899, Temperature This series of errors corresponds to the bits in the STATus:QUEStionable:TEMPerature register. The second column in the table shows the corresponding bit. An event with the error number shown in the table means the condition has been detected.
  • Page 147: Rf Section Troubleshooting (Rf/Microwave Analyzers)

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide RF Section Troubleshooting (RF/Microwave Analyzers) What You Will Find in This Chapter The following information is found in this chapter: 1. Theory of operation of the RF section. 2. Isolating the cause of an hardware problem by verifying the functionality of assemblies in the RF section signal path.
  • Page 148: Rf Section Description

    RF Section Description This section covers only those optional frequency ranges listed below for the N9030A Signal Analyzer. — Option 503, 3.6 GHz Frequency Range — Option 508, 8.4 GHz Frequency Range — Option 513, 13.6 GHz Frequency Range — Option 526, 26.5 GHz Frequency Range The RF input signal can be routed through three different front end signal paths.
  • Page 149 RF Section Troubleshooting (RF/Microwave Analyzers) RF Section Description The RF section is comprised of the following major assemblies: — A9 Input Attenuator A — A10 Input Attenuator B — A11 Low Band Switch Assembly — A12 YTF Preselector — A20 Yig Tuned Oscillator —...
  • Page 150: A9 Input Attenuator A

    RF Section Troubleshooting (RF/Microwave Analyzers) RF Section Description 2. RF input frequencies from 3.6 GHz to 13.6 GHz go through the high band path. Refer to the RF Highband Path #1 Block Diagram in Chapter 13 details. The input signal level can be optimized by Input Attenuator A and/or Input Attenuator B.
  • Page 151: A11 Low Band Switch

    Align routine will perform a rough centering during the preselector two point tuning algorithm. However, when troubleshooting, press Amplitude, Preselector Center to manually center the preselector. The YTF Preselector is not present in analyzers with Option 503, 3.6 GHz frequency range. A20 YTO Assembly Provides the 1st LO signal that is required for the A13 RF Front End Assembly.
  • Page 152: A13 Rf Front End Assembly

    RF Section Troubleshooting (RF/Microwave Analyzers) RF Section Description A13 RF Front End Assembly This assembly consists of two circuit boards. A13A1 contains the major front end conversion components. A13A2 contains the switched filters and LO and IM nulling circuits. A13A1 and A13A2 are not separately replaceable. The entire A13 assembly must be replaced.
  • Page 153 RF Section Troubleshooting (RF/Microwave Analyzers) RF Section Description This assembly contains the following circuits: — Input Low-pass filter (RF input signals < 3.6 GHz) — Optional Low Band Electronic Attenuator (0-24 dB attenuation control) — Optional Low Band Preamplifier and Limiter —...
  • Page 154: Troubleshooting

    RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting Troubleshooting Quick Check to Verify the Low Band Signal Path The analyzer has an internal 50 MHz amplitude reference signal that is used to verify the low band path. This 50 MHz calibrator is used when the analyzer performs many of the internal alignment routines.
  • Page 155 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting Turn off auto align by pressing System, Alignments, Auto Align, Off. IMPORTANT Disconnect the W16 cable from A13A1J7 on the Front End Assembly IF Out.See Figure 4-1. Connect A13A1J7 output to a functioning spectrum analyzer and verify the 322.5 MHz intermediate frequency is measuring −22 dBm ±...
  • Page 156 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting If this power level is incorrect, the following assemblies need to be verified using the 50 MHz internal calibrator signal. Be sure the 50 MHz calibrator is turned on. Press Input/Output, RF Calibrator, 50 MHz when verifying the performance.
  • Page 157: Troubleshooting A Low Band Problem

    RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting Troubleshooting a Low Band Problem Refer to the RF Lowband Path Block Diagram in Chapter 13 and follow the instructions in the settings box. To enable the internal 50 MHz, −25 dBm calibrator signal press Input/Output, RF Calibrator, 50 MHz. The Low Band signal path (sometimes referred to as Band 0) is used for all signals less than 3.6 GHz when the analyzer is used in normal operation.
  • Page 158 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting Figure 4-3 RF Section N9030A PXA Signal Analyzer Service Guide...
  • Page 159 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting A9 Input Attenuator and A10 Input Attenuator Verification Calibrator Switch Test On the A16 Reference assembly, disconnect semi rigid cable W3 from A16J701 and measure A16J701 with a spectrum analyzer. Expected signal is 50 MHz at −25 dBm ±...
  • Page 160 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting Second LO Level Verification The second LO signal comes from the A16 Reference Assembly and is only used in Low Band. The second LO signal can be measured on the Front End Assembly at A13A1J1 or the A16 Reference Assembly at A16J702. Expected signal is 4800 MHz at +10 dBm when a low loss test cable is used and with the measuring spectrum analyzer input attenuator set to at least 20 dB to prevent overload.
  • Page 161 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting The LO input at W20, and the LO outputs were tested when performing the First LO Verification. It is possible to measure the W48 input cable to the Switched Filter where it connects to A13A2J2, and the output of the Switched Filter at W49 where it connects to A13A1J11.
  • Page 162 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting Low Band Preamp (Option P03, P08, P13, P26) The Preamp is aligned as part of the System Gain internal alignment process. See the description of the initial alignments and the location of the alignment history file in Chapter 2, “Boot Up and Initialization Troubleshooting”, on page 51.
  • Page 163: Quick Check To Verify High Band Rf Path

    RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting Quick Check to Verify High Band RF Path Refer to the RF Highband Path #1 Block Diagram in Chapter The High Band signal path (sometimes referred to as Band 1-Band 4) is used for all signals 3.6 GHz and above. If the start frequency is set to 3.6 GHz and above, the analyzer displays only the High Band signal path.
  • Page 164 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting Disconnect cable W16 at A13A1J7, 322.5 MHz output on the Front End Assembly. See Figure 4-4. Select Span, 0 Hz. Figure 4-4 A13A1J7 Location (Options 503, 508, 513, and 526) N9030A PXA Signal Analyzer Service Guide...
  • Page 165 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting Connect A13J7 output to a functioning spectrum analyzer and verify the 322.5 MHz intermediate frequency is measuring −31 ± 4 dB as shown in Figure 4-5. Figure 4-5 322.5 MHz Intermediate Frequency If this power level is correct the Front End assembly is operating correctly in high band.
  • Page 166 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting High Band #2 signal path utilizes a high band mixer internal to the A13 Front End Assembly for input frequencies from 13.6 GHz to 26.5 GHz. Failures from 13.6 GHz − 26.5 GHz will most likely be caused by the A13 RF Front End Assembly.
  • Page 167: Troubleshooting A High Band Problem

    RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting Troubleshooting a High Band Problem Refer to the RF Highband Path #1 Block Diagram in Chapter 13and follow the instructions in the settings box. To enable the internal 4.8 GHz, −28 dBm calibrator signal press Input/Output, RF Calibrator, 4.8 GHz. A13 Front End Input Verification Disconnect W15 from A13A1J9 See Figure 4-7...
  • Page 168 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting To perform the YTF alignment, reconnect W15 cable, and press System, Alignments, More, Ad vanced, Characterize Preselector. The routine may take several minutes to align the YTF. Display the 4.8 GHz calibrator signal on screen as explained in the quick check section.
  • Page 169 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting To verify calibrator switch operation, connect external signal source set to 4.8 GHz and −25 dBm to the RF input connector of analyzer under test. Press Input/Output, RF Calibrator, Off. If the signal level at the attenuator output is now correct, suspect the A9 Attenuator cal switch or a faulty control signal from the A15 Front End Controller assembly.
  • Page 170 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting the analyzer LO phase lock loop to unlock, which would affect the LO frequency measurement. The LO signal should measure 5122.5 MHz at +10 dBm ± 3 dB. If the signal level is incorrect, measure the signal coming from the A20 YTO at A13A1J4.
  • Page 171 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting High Band Mixing Equations For input signal frequencies from 3.6 GHz to 8.4 GHz and 13.6 GHz to 17 GHz: RF = LO x N − IF IF = LO x N − RF LO x N = IF + RF where RF is the input signal at the signal analyzer where N is the harmonic mixing mode:...
  • Page 172 RF Section Troubleshooting (RF/Microwave Analyzers) Troubleshooting N9030A PXA Signal Analyzer Service Guide...
  • Page 173: Rf Section Troubleshooting (Millimeter-Wave Analyzers)

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide RF Section Troubleshooting (Millimeter-Wave Analyzers) What You Will Find in This Chapter The following information is found in this chapter: 1. Theory of operation of the RF section. 2. Isolating the cause of an hardware problem by verifying the functionality of assemblies in the RF section signal path.
  • Page 174: Rf Section Description

    RF Section Troubleshooting (Millimeter-Wave Analyzers) RF Section Description RF Section Description This section covers only those optional frequency ranges listed below for the N9030A Signal Analyzer. — Option 543, 43 GHz Frequency Range — Option 544, 44 GHz Frequency Range —...
  • Page 175 RF Section Troubleshooting (Millimeter-Wave Analyzers) RF Section Description The RF section is comprised of the following major assemblies: — A9 Input Attenuator A — A10 Input Attenuator B — A11 Low Band Switch Assembly — A12 YTF Preselector — A20 Yig Tuned Oscillator —...
  • Page 176: A9 Input Attenuator A

    RF Section Troubleshooting (Millimeter-Wave Analyzers) RF Section Description 2. RF input frequencies from 3.6 GHz to 17.1 GHz go through the high band path. Refer to the RF Highband Path #1 Block Diagram (Millimeter-Wave Analyzers) in Chapter 13 for details. The input signal level can be optimized by Input Attenuator A and/or Input Attenuator B.
  • Page 177: A10 Input Attenuator B

    RF Section Troubleshooting (Millimeter-Wave Analyzers) RF Section Description A10 Input Attenuator B This assembly has a total of 60 dB of attenuation to control the signal level into the Low Band Switch assembly. There is a 10 dB, 20 dB, and 30 dB section in the A10 assembly.
  • Page 178: A13 Rf Front End Assembly (Options 543, 544, 550)

    RF Section Troubleshooting (Millimeter-Wave Analyzers) RF Section Description A13 RF Front End Assembly (Options 543, 544, 550) This assembly consists of two circuit boards. A13A1 contains the major front end conversion components. A13A2 contains the switched filters and LO and IM nulling circuits.
  • Page 179 RF Section Troubleshooting (Millimeter-Wave Analyzers) RF Section Description This assembly contains the following circuits: — Input Low-pass filter (RF input signals < 3.6 GHz) — Optional Low Band Electronic Attenuator (0-24 dB attenuation control) — Optional Low Band Preamplifier and Limiter —...
  • Page 180: Troubleshooting

    RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting Troubleshooting Quick Check to Verify the Low Band Signal Path The analyzer has an internal 50 MHz amplitude reference signal that is used to verify the low band path. This 50 MHz calibrator is used when the analyzer performs many of the internal alignment routines.
  • Page 181 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting Turn off auto align by pressing System, Alignments, Auto Align, Off. IMPORTANT Disconnect the W16 cable from A13A1J7 on the Front End Assembly IF Out. Figure 5-1. Connect A13A1J7 output to a functioning spectrum analyzer and verify the 322.5 MHz intermediate frequency is measuring −22 dBm ±...
  • Page 182 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting If this power level is incorrect, the following assemblies need to be verified using the 50 MHz internal calibrator signal. Be sure the 50 MHz calibrator is turned on. Press Input/Output, RF Calibrator, 50 MHz when verifying the performance.
  • Page 183: Troubleshooting A Low Band Problem

    RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting Troubleshooting a Low Band Problem Refer to the RF Lowband Path Block Diagram (Millimeter-Wave Analyzers) in Chapter 13 and follow the instructions in the settings box. To enable the internal 50 MHz, −25 dBm calibrator signal press Input/Output, RF Calibrator, 50 MHz.
  • Page 184 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting Figure 5-3 RF Section (Options 543, 544, and 550) N9030A PXA Signal Analyzer Service Guide...
  • Page 185 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting A9 Input Attenuator and A10 Input Attenuator Verification Calibrator Switch Test On the A16 Reference assembly, disconnect semi rigid cable W3 from A16J701 and measure A16J701 with a spectrum analyzer. Expected signal is 50 MHz at −25 dBm ±...
  • Page 186 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting Second LO Level Verification The second LO signal comes from the A16 Reference Assembly and is only used in Low Band. The second LO signal can be measured on the Front End Assembly at A13A1J1 or the A16 Reference Assembly at A16J702. Expected signal is 4800 MHz at +10 dBm when a low loss test cable is used and with the measuring spectrum analyzer input attenuator set to at least 20 dB to prevent overload.
  • Page 187 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting The LO input at W20, and the LO outputs were tested when performing the First LO Verification. It is possible to measure the W48 input cable to the Switched Filter where it connects to A13A2J2, and the output of the Switched Filter at W49 where it connects to A13A1J11.
  • Page 188 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting Low Band Preamp (Option P03, P08, P13, P26, P43, P44, P50) The Preamp is aligned as part of the System Gain internal alignment process. See the description of the initial alignments and the location of the alignment history file in Chapter 2, “Boot Up and Initialization Troubleshooting”, on page 51.
  • Page 189: Quick Check To Verify High Band Rf Path

    RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting Quick Check to Verify High Band RF Path Refer to the RF Highband Path #1 Block Diagram (Options 543, 544, and 550) Chapter The High Band signal path (sometimes referred to as Band 1-Band 6) is used for all signals 3.6 GHz and above.
  • Page 190 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting Turn off auto align by pressing System, Alignments, Auto Align, Off. IMPORTANT Disconnect cable W16 at A13A1J7, 322.5 MHz output on the Front End Assembly. See Figure 5-4. Select Span, 0 Hz. Figure 5-4 A13A1J7 Location (Options 543, 544, and 550) N9030A PXA Signal Analyzer Service Guide...
  • Page 191 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting Connect A13J7 output to a functioning spectrum analyzer and verify the 322.5 MHz intermediate frequency is measuring −31 ± 4 dB as shown in Figure 5-5. Figure 5-5 322.5 MHz Intermediate Frequency If this power level is correct the Front End assembly is operating correctly in high band.
  • Page 192 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting High Band #2 signal path utilizes a high band mixer internal to the A13 Front End Assembly for input frequencies from 17.0 GHz to 34.5 GHz. High Band #3 signal path utilizes a high band mixer internal to the A13 Front End Assembly for input frequencies from 34.4 to 50 GHz.
  • Page 193: Troubleshooting A High Band Problem

    RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting Troubleshooting a High Band Problem Refer to the RF Highband Path #1 Block Diagram (Option 543, 544, 550) in Chapter 13 and follow the instructions in the settings box. To enable the internal 4.8 GHz, −28 dBm calibrator signal press Input/Output, RF Calibrator, 4.8 GHz.
  • Page 194 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting To perform the YTF alignment, reconnect W62 or W57 cable, and press System, Alignments, More, Ad vanced, Characterize Preselector. The routine may take several minutes to align the YTF. Display the 4.8 GHz calibrator signal on screen as explained in the quick check section.
  • Page 195 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting To verify calibrator switch operation, connect external signal source set to 4.8 GHz and −25 dBm to the RF input connector of analyzer under test. Press Input/Output, RF Calibrator, Off. If the signal level at the attenuator output is now correct, suspect the A9 Attenuator cal switch or a faulty control signal from the A15 Front End Controller assembly.
  • Page 196 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting the analyzer LO phase lock loop to unlock, which would affect the LO frequency measurement. The LO signal should measure 5122.5 MHz at +10 dBm ± 3 dB. If the signal level is incorrect, measure the signal coming from the A20 YTO at A13A1J4.
  • Page 197 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting High Band Mixing Equations For input signal frequencies from 3.6 GHz to 8.4 GHz: RF = LO x N − IF IF = LO x N − RF LO x N = IF + RF where RF is the input signal at the signal analyzer where N is the harmonic mixing mode: N = 1 for 3.5 GHz to 8.4 GHz...
  • Page 198 RF Section Troubleshooting (Millimeter-Wave Analyzers) Troubleshooting N9030A PXA Signal Analyzer Service Guide...
  • Page 199: Front End Control Troubleshooting

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide Front End Control Troubleshooting What You Will Find in This Chapter The following information is presented in this chapter: 1. Theory of operation of the Front End Control section. 2. Isolating the cause of a hardware problem by verifying the functionality of assemblies of the Front End Control.
  • Page 200: A15 Front End Control Description

    Front End Control Troubleshooting A15 Front End Control Description A15 Front End Control Description Purpose The A15 Front End Controller board functionality can be broken down into (3) main categories 1. Provides switch control logic and bias voltages to the major RF front end assemblies in the N9030A Signal Analyzer.
  • Page 201 Front End Control Troubleshooting A15 Front End Control Description Table 6-1 A15 Option Related Control Option Description Physical Location in the Analyzer 100 kHz to 3.6 GHz Internal Preamplifier A15 to A13 100 kHz to 8.4 GHz Internal Preamplifier A15 to A11 and A13 100 kHz to 13.6 GHz Internal Preamplifier A15 to A11 and A13 100 kHz to 26.5 GHz Internal Preamplifier...
  • Page 202 Front End Control Troubleshooting A15 Front End Control Description Figure 6-1 A15 Front View, Physical Connectors The table below describes the connector location and the final destinations of the RF signal, switch control logic or bias voltage. Table 6-2 A15 Connectors and Destinations A15 Connector Description Destination...
  • Page 203 Front End Control Troubleshooting A15 Front End Control Description Table 6-2 A15 Connectors and Destinations A15 Connector Description Destination Designation J801 YTF Bypass Out To SW1 & SW2 (Option MPB with Option 508, 513, or 526) To SW4 (Option MPB with Option 543, 544, or 550) J700 Low Band Switch Logic Out To A11...
  • Page 204: A15 Front End Control Assembly Troubleshooting

    Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting A15 Front End Control Assembly Troubleshooting The N9020A, MXA Signal Analyzer utilizes an RF front end troubleshooting board that can be used to verify some, but not all of the control circuitry on the N9030A, PXA Signal Analyzer due to the additions of front end assemblies.
  • Page 205: Verifying Input Attenuator A, Input Attenuator B, Low Band Switch Logic And Power Supplies

    Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Verifying Input Attenuator A, Input Attenuator B, Low Band Switch Logic and Power Supplies 1. Turn off the instrument. 2. Disconnect ribbon cables from A15J700 and A15J800 as shown Figure 6-2.
  • Page 206 503, 508, 513, or 526 543, 544, 550 4. If the PXA has frequency range option 503, 508, 513, or 526, also connect the Low Band Switch Control Cable, E4410-60160 between A15J700 and J2 of the RF Front End Troubleshooting board. Do not connect this cable if the frequency range option is 543, 544, or 550.
  • Page 207 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting 5. Place the RF front end troubleshooting board on an ESD safe bag or foam to ensure nothing shorts out. See Figure 6-4. Figure 6-4 RF Front End Troubleshooting Board Placement 6.
  • Page 208 If any of the power supply LED's are not turned on, see Chapter 2, “Boot Up and Initialization Troubleshooting”. Input Attenuator A Control Logic Verification (Option 503, 508, 513, 526) Press AMPTD, Attenuation 0 dB on the analyzer. Attenuation LED's DS15-20 on the test board should be off.
  • Page 209 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Input Attenuator A Control Logic Verification (Option 543, 544, 550) Ignore DS11 in this procedure. Press System, Show, Hard ware. Look for an entry for the Low Band Switch and verify that the HW ID is 45. If the HW ID is something other than 45 (for example, 10) or there is no entry for the Low Band Switch, the analyzer will control the attenuators as if they are 26.5 GHz attenuators, not the 50 GHz attenuators that are actually installed.
  • Page 210 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Input Attenuator B Control Logic Verification (Option 503, 508, 513, 526) Press AMPTD, Attenuation 6 dB on the analyzer and verify the 6 dB Step LED DS17 is illuminated. Change to the input attenuation settings found in...
  • Page 211 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Input Attenuator B Control Logic Verification (Option 543, 544, 550) Press AMPTD, Attenuation 10 dB on the analyzer and verify that the 10 dB Step LED DS18 is illuminated. Table 6-8 Input Attenuator B LED’s (Opt 543, 544, 550) Attenuator Setting DS17...
  • Page 212 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Low Band Switch Control Logic Verification (Option 503, 508, 513, 526 only) If your PXA has option 543, 544, or 550, skip to “Disconnect RF Front End Troubleshooting Board” on page 213.
  • Page 213 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Disconnect RF Front End Troubleshooting Board You do not need the RF front end troubleshooting board to test out the remaining front end hardware components. At this point it is advisable to shutdown the analyzer and disconnect the test board and cables.
  • Page 214: Preselector Tune Output

    Press Span, Zero Span on the analyzer. The preselector tune output voltage in high band should change when the center frequency of the analyzer is changed. Preselector tune output measurements are not valid for Option 503, 3 GHz frequency range. Table 6-11...
  • Page 215 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Table 6-12 Preselector Tune Output Voltages (Option 543, 544, 550) Center Frequency ~ Tune Vol tage Valid Frequency (GHz) (VDC) Range Option 543, 544, 550 10.0 543, 544, 550 15.0 543, 544, 550 20.0 543, 544, 550...
  • Page 216: Verifying Sw3 (Option Lnp Only)

    Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Verifying SW3 (Option LNP only) Since there is a ribbon cable from the A15J802 to SW3, it is not feasible to use a voltmeter or oscilloscope to measure the control voltages. For testing SW3, the “click”...
  • Page 217: Verifying Microwave Preselector Bypass Switch (Option Mpb)

    Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Verifying Microwave Preselector Bypass Switch (Option MPB) If the analyzer has frequency range option 508, 513, or 526, the switches which perform the microwave preselector bypass are SW1 and SW2, which operate in unison.
  • Page 218: Oscilloscope Test

    Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Oscilloscope Test Measurements can be made to verify the current logic is getting to the appropriate switch from the A15. In order to perform this measurement, the outer cover and chassis RF bracket on the right hand side of the instrument must be removed.
  • Page 219 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Figure 6-6 SW4 Connector Location (Option 543, 544, and 550) Figure 6-7 Connector Close-up To verify the control logic, press Mode Preset on the analyzer. Press FREQ, 5 GHz, SPAN, 1 MHz, AMPTD, More 1 of 2, uW Path Ctrl. Standard Path is selected by default.
  • Page 220 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Figure 6-8 Connector Detail The voltage should be ~21.5 VDC steady state at this point. When you switch from Standard Path to uW Preselector Bypass, you should see a negative going pulse to 0 VDC on the oscilloscope for ~15 mS before the voltage returns to ~21.5 VDC steady state.
  • Page 221 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting functioning spectrum analyzer if the Front End Controller board is switching this level correctly. If -23 dBm is not being measured correctly, remove the cable labeled J902 from the Front End Controller board and measure the output of that cable.
  • Page 222 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting The I.F. switch path and frequency generation occurs on the A15, Front End Controller board. This troubleshooting procedure provides the instrument setups to verify options CR3, CRP and ALV. Test the Aux I.F. output based on the options installed in the analyzer.
  • Page 223 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Verifying Option CRP Press the following keys on the analyzer: Mode, Spectrum Analyzer, Mode Preset, Input/Output, RF Calibrator, 50 MHz, Freq, 50 MHz, Span, 0 Hz, System, Alignments, Auto Align, Off, Input/Output, More 1 of 2, Output Config, Aux IF Out, Arbitrary IF.
  • Page 224 Front End Control Troubleshooting A15 Front End Control Assembly Troubleshooting Verifying Option ALV Equipment needed: Volt meter Adapters and cables to connect the volt meter to the Aux IF Out SMA connector on the spectrum analyzer rear panel. Signal source Signal source settings: Frequency: 1 GHz (CW) Amplitude: −10 dBm...
  • Page 225: Analog/Digital If Troubleshooting

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide Analog/Digital IF Troubleshooting What You Will Find in This Chapter The following information is presented in this chapter: 1. Theory of operation of the IF section. 2. Isolating the cause of a hardware problem by verifying the functionality of assemblies in the IF section signal path.
  • Page 226: A2 Analog If Assembly Description

    Analog/Digital IF Troubleshooting A2 Analog IF Assembly Description A2 Analog IF Assembly Description When the 10 MHz or 25 MHz IF Path is selected, or when any swept measurement is made, the analyzer's RF input signal is down converted to a 322.5 MHz intermediate frequency in the A13 RF Front End Assembly.
  • Page 227: A2 Analog If Assembly Theory Of Operation

    Analog/Digital IF Troubleshooting A2 Analog IF Assembly Theory of Operation A2 Analog IF Assembly Theory of Operation Refer to Chapter 13, “Block Diagrams”. Input Switch and Filter A 322.5 MHz input signal is received from the A15 Front End Control Assembly.
  • Page 228 Analog/Digital IF Troubleshooting A2 Analog IF Assembly Theory of Operation Post Down Conversion Amplification and Prefiltering The 22.5 MHz IF goes through a fixed gain amplifier. Then prefilters are switched in and out. The signal then goes through a variable gain amplifier. The prefilters provide four single-pole filters to limit the bandwidth of the signal reaching the ADC on the A3 Digital IF assembly.
  • Page 229 Analog/Digital IF Troubleshooting A2 Analog IF Assembly Theory of Operation Anti-Alias Filter and Final Amplifier The anti-alias filters attenuate unwanted out-of-band noise and distortion products. The first anti-alias filter is centered at 22.5 MHz and is 25 MHz wide. The signal can bypass the second anti-alias filter when the analyzer utilizes either the IQ Analyzer swept, or wide-band demod.
  • Page 230: A2 Analog If Troubleshooting

    Analog/Digital IF Troubleshooting A2 Analog IF Troubleshooting A2 Analog IF Troubleshooting There are three steps to verify the A2 Analog IF Assembly. — Measure the input power and frequency accuracy of the 322.5 MHz signal (from the A13 RF Front End assembly) —...
  • Page 231 Analog/Digital IF Troubleshooting A2 Analog IF Troubleshooting 8. Carefully disconnect W25 cable at A15J900 as shown in Figure 7-1. Figure 7-1 A15 RF Front End Control Assembly 9. Connect A15J900 to a functioning spectrum analyzer using the appropriate MMCX connectors and cables. 10.Press Freq, 322.5 MHz, Span, 1 MHz, Peak Search on the functioning spectrum analyzer.
  • Page 232 Analog/Digital IF Troubleshooting A2 Analog IF Troubleshooting 11.The analyzer should read 322.5 MHz at −23 dBm ± 3 dB as shown in Figure 7-2. Figure 7-2 A15 322.5 MHz Output If the 322.5 MHz signal is not measuring the correct power level, refer to Chapter 4, “RF Section Troubleshooting (RF/Microwave Analyzers)”...
  • Page 233: Verifying The 22.5 Mhz Output Power

    Analog/Digital IF Troubleshooting A2 Analog IF Troubleshooting Verifying the 22.5 MHz Output Power 1. Perform an instrument shutdown. 2. Turn the instrument over so the bottom side of the analyzer is facing up. 3. Turn on the PXA Signal Analyzer and wait for the instrument to complete the boot up process.
  • Page 234 Analog/Digital IF Troubleshooting A2 Analog IF Troubleshooting 10.Press Freq, 22.5 MHz, Span, 1 MHz, Peak Search on the functioning spectrum analyzer. 11.The analyzer marker should read 22.5 MHz at −25 dBm ± 4 dB as shown in Figure 7-4. Figure 7-4 A2 Analog IF Output 12.If the 22.5 MHz signal is not measuring the correct power level, do not assume the Analog IF is the most probable cause until the 3rd LO...
  • Page 235: Verifying The 300 Mhz Lo Input Power From The A16 Reference Assembly

    Analog/Digital IF Troubleshooting A2 Analog IF Troubleshooting Verifying the 300 MHz LO Input Power from the A16 Reference Assembly 1. Referring to Figure 7-5, carefully disconnect the W36 at A2J300. Figure 7-5 A2 Analog IF Cables 2. Connect the W36 cable to the MMCX female to SMA female adapter. Use an appropriate cable to go from the SMA adapter to the RF input of a functioning spectrum analyzer.
  • Page 236 Analog/Digital IF Troubleshooting A2 Analog IF Troubleshooting 4. The analyzer marker should read 300 MHz at 10 dBm ± 3 dB as shown in Figure 7-6. Figure 7-6 300 MHz LO 5. If the 300 MHz signal is not measuring the correct power level, see the A16 Reference Assembly troubleshooting section in this service guide.
  • Page 237: A3 Digital If Assembly Description

    Analog/Digital IF Troubleshooting A3 Digital IF Assembly Description A3 Digital IF Assembly Description The A3 Digital I.F. has circuitry that is needed to analyze complex communication signals that can occupy up to 40 MHz of information bandwidth. This assembly has two inputs: 1.
  • Page 238: A3 Digital If Assembly Theory Of Operation

    Analog/Digital IF Troubleshooting A3 Digital IF Assembly Theory of Operation A3 Digital IF Assembly Theory of Operation Refer to Chapter 13, “Block Diagrams.”. Data Acquisition The 22.5 MHz IF comes from the A2 Analog IF assembly. The input level to the A3 Digital IF assembly is −25 dBm when observing the 50 MHz calibrator signal.
  • Page 239 Analog/Digital IF Troubleshooting A3 Digital IF Assembly Theory of Operation The signal then passes through a 30 MHz to 90 MHz tripler. A 0 to 5V, 30 MHz square wave is generated. Capacitors form a single-pole band pass filter to select the 3rd harmonic, 90 MHz. Noise Source Voltage Regulator Various external noise sources can be connected to the rear panel of the PXA Signal Analyzer.
  • Page 240: A3 Digital If Troubleshooting

    Analog/Digital IF Troubleshooting A3 Digital IF Troubleshooting A3 Digital IF Troubleshooting Verifying the 22.5 MHz Input Power 1. Perform an instrument shutdown. 2. Remove the cover of the PXA Signal Analyzer. Refer to Chapter 16, “Assembly Replacement Procedures”, on page 417 in this service guide.
  • Page 241 Analog/Digital IF Troubleshooting A3 Digital IF Troubleshooting 9. Referring to Figure 7-7, carefully disconnect W42 cable at A3J19. Figure 7-7 A3 Digital IF Cables 10.Connect the W42 cable to the MMCX female to SMA female connector. Use an appropriate cable to go from the SMA connector to the RF input of a functioning spectrum analyzer to verify the 22.5 MHz I.F.
  • Page 242 Analog/Digital IF Troubleshooting A3 Digital IF Troubleshooting 12.The analyzer should read 22.5 MHz at −25 dBm ± 4 dB as shown in Figure 7-8. Figure 7-8 22.5 MHz IF Input 13.If the 22.5 MHz signal is not measuring the correct power level, see “A2 Analog IF Troubleshooting”...
  • Page 243: Verifying The 250 Mhz If Input Power (Option B40 Only)

    Analog/Digital IF Troubleshooting A3 Digital IF Troubleshooting Verifying the 250 MHz IF Input Power (Option B40 only) Perform this procedure only if the analyzer is equipped with Option B40, Analysis Bandwidth, 40 MHz. 1. Perform an instrument shutdown. 2. Remove the cover of the PXA Signal Analyzer. Refer to Chapter 16, “Assembly Replacement Procedures”, on page 417 in this service guide.
  • Page 244 Analog/Digital IF Troubleshooting A3 Digital IF Troubleshooting Figure 7-9 A3 Digital IF Cables 11.Connect the W26 or W40 cable to the MMCX female to SMA female connector. Use an appropriate cable to go from the SMA connector to the RF input of a functioning spectrum analyzer to verify the 250 MHz I.F. signal frequency and amplitude is correct.
  • Page 245 Analog/Digital IF Troubleshooting A3 Digital IF Troubleshooting 13.The analyzer marker should read 250 MHz at −30 dBm ± 4 dB as shown in Figure 7-12. Figure 7-10 250 MHz IF Input 14.If the 250 MHz signal is not measuring the correct power level, see “A15 Front End Control Assembly Troubleshooting”...
  • Page 246: Verifying The 100 Mhz Reference Input

    Analog/Digital IF Troubleshooting A3 Digital IF Troubleshooting Verifying the 100 MHz Reference Input 1. Perform an instrument shutdown. 2. Remove the cover of the PXA Signal Analyzer. Refer to Chapter 16, “Assembly Replacement Procedures”, on page 417 in this service guide. 3.
  • Page 247 Analog/Digital IF Troubleshooting A3 Digital IF Troubleshooting 10.The analyzer marker should read 100 MHz at +10 dBm ± 4 dB as shown in Figure 7-12. Figure 7-12 100 MHz Reference Input 11.If the 100 MHz signal is measuring incorrectly, see See “A16 Reference Assembly Troubleshooting”...
  • Page 248 Analog/Digital IF Troubleshooting A3 Digital IF Troubleshooting N9030A PXA Signal Analyzer Service Guide...
  • Page 249: Lo Synthesizer/Reference Troubleshooting

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide LO Synthesizer/Reference Troubleshooting What You Will Find in This Chapter The following information is presented in this chapter: 1. Theory of operation of the LO Synthesizer/Reference section. 2. Isolating the cause of a hardware problem by verifying the functionality of assemblies in the LO Synthesizer and Reference sections.
  • Page 250: A14 Lo Synthesizer Assembly Description

    LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer Assembly Description A14 LO Synthesizer Assembly Description Purpose The L.O. Synthesizer assembly provides the power and drive to the A20 YTO (YIG Tuned Oscillator). The A20 YTO is used as the 1st Local Oscillator (1st LO) in the A13A1 Front End Assembly for RF conversion.
  • Page 251: A14 Lo Synthesizer Theory Of Operation

    LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer Theory of Operation A14 LO Synthesizer Theory of Operation Refer to Chapter 13, “Block Diagrams”. The LO Synthesizer can be operated in either dual-loop or single-loop modes. The dual-loop mode provides lower phase noise but slower tuning speed. The single-loop mode provides for fast tuning.
  • Page 252: Manual Selection Of Single Versus Dual Loop Operation

    LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer Theory of Operation synthesizer output drives the LO port of a mixer. The 1st LO from the A13A1 Front End drives the RF port of the mixer. The signal at the IF port, which should be between 33 and 55 MHz (or between 78 and 88 MHz), drives the phase/frequency detector.
  • Page 253: Brief Description Of The Major Blocks

    LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer Theory of Operation Brief Description of the Major Blocks: — The Field Programmable Gate Array (FPGA) L.O. Controller has the capability to pretune the A20 YTO, detect unlocks, and control the fractional-N divider, main loop, and offset loop. —...
  • Page 254: A14 Lo Synthesizer And A20 Yto Troubleshooting

    LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting Turn on the N9030A Signal Analyzer and wait for the instrument to complete the boot up process. There are 8 processes to perform, which will verify the L.O.
  • Page 255 LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting Figure 8-1 A14 LO Synthesizer Assembly N9030A PXA Signal Analyzer Service Guide...
  • Page 256: Verifying The 4800 Mhz 1St Lo Reference Power And Frequency Stability

    LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting Verifying the 4800 MHz 1st LO Reference Power and Frequency Stability: 1. Turn on the N9030A Signal Analyzer and wait for the instrument to complete the boot up process. 2. Press FREQ, 50 MHz, SPAN, Zero Span, Meas Setup, PhNoise Opt, Best Close in PNoise.
  • Page 257 LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting Figure 8-3 4800 MHz Wide Span N9030A PXA Signal Analyzer Service Guide...
  • Page 258 LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting 7. Verify the 4800 MHz signal from the A16 Reference Assembly is stable by pressing SPAN, 50 kHz, BW, 1 kHz on the functioning spectrum analyzer. The signal on the functioning spectrum analyzer should be very stable both in frequency and power as shown in Figure 8-4.
  • Page 259: Verifying The 100 Mhz Lo Synth Reference Power And Frequency Stability

    LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting Verifying the 100 MHz LO Synth Reference Power and Frequency Stability: 1. Turn on the N9030A Signal Analyzer and wait for the instrument to complete the boot up process. 2. Press FREQ, 50 MHz, SPAN, Zero Span. 3.
  • Page 260 LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting 6. Press Peak Search on the functioning spectrum analyzer. The analyzer marker should read 100 MHz at +13 dBm ±3 dB as shown in Figure 8-6. Figure 8-6 100 MHz Wide Span N9030A PXA Signal Analyzer Service Guide...
  • Page 261 LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting 7. Verify the 100 MHz signal from the A16 Reference Assembly is stable by pressing SPAN, 50 kHz, BW, 1 kHz on the functioning spectrum analyzer. The signal on the functioning spectrum analyzer should be very stable both in frequency and power as shown in Figure 8-4.
  • Page 262: Verifying The 1St Lo Power And Frequency

    LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting Verifying the 1st LO Power and Frequency: 1. Turn on the N9030A Signal Analyzer and wait for the instrument to complete the boot up process. 2. Press FREQ, 50 MHz, SPAN, Zero Span. 3.
  • Page 263 LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting 8. The analyzer marker should read 5172.5 MHz at 0 dBm ± 4 dB as shown in Figure 8-9. Figure 8-9 5.1725 GHz 1st LO Measurement Due to the nominal 10 dB coupling factor of the directional coupler, the actual power at the YTO output will be approximately 10 dB higher than the power level measured by the functioning spectrum analyzer.
  • Page 264 LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting Table 8-1 1st LO Frequency and Power Level Measurements PXA Signal Analyzer Center Expected LO Frequency Expected LO Power at Equivalent LO Power) Frequency (GHz) at Directional Directional Coupler at YTO Output (GHz) Coupler Output Output...
  • Page 265 LO Synthesizer/Reference Troubleshooting A14 LO Synthesizer and A20 YTO Troubleshooting Figure 8-11 4.6225 GHz 1st LO Measurement Figure 8-12 7.3225 GHz 1st LO Measurement N9030A PXA Signal Analyzer Service Guide...
  • Page 266: A16 Reference Assembly Description

    LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Description A16 Reference Assembly Description Purpose The A16 Reference Assembly provides the fundamental reference signals from which all instrument local oscillator and synchronous timing signals are derived. The reference board also uses these same signals to generate CW and modulated RF calibration signals and a 10 MHz time base signal for the instrument.
  • Page 267 LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Description Table 8-2 lists all the reference signals provided by the A16 Reference Assembly. Table 8-2 A16 Reference Assembly Signals Signal Description From Location Originates From To Location Purpose External Reference Input Input from User A16704 Phase Lock analyzer with (1 to 50 MHz,...
  • Page 268: A16 Reference Assembly Troubleshooting

    LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Troubleshooting A16 Reference Assembly Troubleshooting If the A16 Reference Assembly is suspect, verify the reference signals, local oscillator output frequencies, and power levels as per Table 8-3 using a functioning spectrum analyzer. In order to measure the signals, you will need to remove the top brace.
  • Page 269 LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Troubleshooting Table 8-3 A16 Reference Assembly Signal Measurement Details Signal Signal Expected Expected Power Special Instrument Figure Description Location Frequency Level Cond itions (MHz) (dBm) Figure 50 MHz A16J705 50 MHz −26 to −29 dBm While monitoring A16J705 Ecal Out typical...
  • Page 270 LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Troubleshooting Figure 8-15 50 MHz Ecal Out Figure 8-16 4.8 GHz 2nd LO Out N9030A PXA Signal Analyzer Service Guide...
  • Page 271 LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Troubleshooting Figure 8-17 4.8 GHz 1st LO Ref Out Figure 8-18 50 MHz Ref Out N9030A PXA Signal Analyzer Service Guide...
  • Page 272 LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Troubleshooting Figure 8-19 4.8 GHz Ref Out Figure 8-20 2.4 GHz Ref Output N9030A PXA Signal Analyzer Service Guide...
  • Page 273 LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Troubleshooting Figure 8-21 300 MHz LO AIF Figure 8-22 100 MHz Ref Out N9030A PXA Signal Analyzer Service Guide...
  • Page 274 LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Troubleshooting Figure 8-23 100 MHz Ref B Out N9030A PXA Signal Analyzer Service Guide...
  • Page 275: Diagnostic Leds

    LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Troubleshooting Diagnostic LEDs There are two sets of diagnostics LEDs on the A16 Reference Assembly. Six LEDs are on the right side of the A16 Reference Main board and five LEDs are on the A16A1 Reference Daughter board. Refer to Figure 8-14.
  • Page 276 LO Synthesizer/Reference Troubleshooting A16 Reference Assembly Troubleshooting N9030A PXA Signal Analyzer Service Guide...
  • Page 277: Cpu/Disk Drive Troubleshooting

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide CPU/Disk Drive Troubleshooting What You Will Find in This Chapter The following information is presented in this chapter: 1. Theory of operation of the CPU section. 2. Isolating the cause of a hardware problem by verifying the functionality of assemblies in the CPU section.
  • Page 278: A4 Cpu Description

    CPU/Disk Drive Troubleshooting A4 CPU Description A4 CPU Description If the CPU board is suspect in an instrument failure, a full description of the instrument boot process is described in Chapter 2, “Boot Up and Initialization Troubleshooting”. Disk Drive The A5 Disk Drive can easily be removed from the A4 CPU assembly without removing instrument covers.
  • Page 279: Rear Panel Connectivity

    SODIMM memory modules. While the memory controller chips do support a wide range of DDR memory types, only memory fully qualified by Keysight Technologies is supported. Full qualification includes mechanical vibration and shock, thermal and power dissipation and the basic electrical characteristics.
  • Page 280: A4 Processor Board Assembly Troubleshooting

    CPU/Disk Drive Troubleshooting A4 Processor Board Assembly Troubleshooting A4 Processor Board Assembly Troubleshooting The A4 Processor board assembly is serviced as an assembly only; no component level repair is supported. Boot-Up or Initialization Problems Typical failures of the A4 Processor board assembly will cause the instrument to not boot-up or initialize properly.
  • Page 281: Bios Settings

    To successfully navigate the BIOS Setup Utility you will need to have an external USB keyboard connected to the instrument. Then, when the initial Keysight Technologies splash screen is displayed at power-up, press F2 on the keyboard. Once this is pressed you should see a display like that of...
  • Page 282 CPU/Disk Drive Troubleshooting A4 Processor Board Assembly Troubleshooting Figure 9-3 BIOS Setup Utility - Information Figure 9-4 BIOS Setup Utility - Information > Version N9030A PXA Signal Analyzer Service Guide...
  • Page 283 CPU/Disk Drive Troubleshooting A4 Processor Board Assembly Troubleshooting Figure 9-5 BIOS Setup Utility - Information > System Monitors Figure 9-6 BIOS Setup Utility - Configuration N9030A PXA Signal Analyzer Service Guide...
  • Page 284 CPU/Disk Drive Troubleshooting A4 Processor Board Assembly Troubleshooting Figure 9-7 BIOS Setup Utility - Configuration > IDE Devices Figure 9-8 BIOS Setup Utility - Configuration > Video N9030A PXA Signal Analyzer Service Guide...
  • Page 285 CPU/Disk Drive Troubleshooting A4 Processor Board Assembly Troubleshooting Figure 9-9 BIOS Setup Utility - Configuration > Video > IGD-LCD Control Figure 9-10 BIOS Setup Utility - Configuration > USB N9030A PXA Signal Analyzer Service Guide...
  • Page 286 CPU/Disk Drive Troubleshooting A4 Processor Board Assembly Troubleshooting Figure 9-11 BIOS Setup Utility - Configuration > LAN Figure 9-12 BIOS Setup Utility - Configuration > PCI Expansion Slot N9030A PXA Signal Analyzer Service Guide...
  • Page 287 CPU/Disk Drive Troubleshooting A4 Processor Board Assembly Troubleshooting Figure 9-13 BIOS Setup Utility - Configuration > Power Control Figure 9-14 BIOS Setup Utility - Configuration > Security N9030A PXA Signal Analyzer Service Guide...
  • Page 288 CPU/Disk Drive Troubleshooting A4 Processor Board Assembly Troubleshooting Figure 9-15 BIOS Setup Utility - Configuration > CPU Figure 9-16 BIOS Setup Utility - Configuration > Advanced N9030A PXA Signal Analyzer Service Guide...
  • Page 289 CPU/Disk Drive Troubleshooting A4 Processor Board Assembly Troubleshooting Figure 9-17 BIOS Setup Utility - Configuration > Advanced > Keyboard Features Figure 9-18 BIOS Setup Utility - Boot N9030A PXA Signal Analyzer Service Guide...
  • Page 290 CPU/Disk Drive Troubleshooting A4 Processor Board Assembly Troubleshooting Figure 9-19 BIOS Setup Utility - Boot > Boot Order Figure 9-20 BIOS Setup Utility - Exit N9030A PXA Signal Analyzer Service Guide...
  • Page 291: A5 Disk Drive

    CPU/Disk Drive Troubleshooting A5 Disk Drive A5 Disk Drive There are two different types of A5 Disk Drives available. The standard drive is a typical hard disk drive, while the option SSD drive is a solid state (FLASH) drive. There are different drive capacities being used, and due to continual changes being made by the drive manufacturers these will continue to change from time to time.
  • Page 292: Overview

    CPU/Disk Drive Troubleshooting A5 Disk Drive Overview The A5 Disk Drive assembly has been divided up into four different partitions. They are: This partition contains the operating system and software installed by Keysight. This is an open system which means you can install additional software, which should be installed on the C: drive.
  • Page 293: Troubleshooting Software Related Issues

    CPU/Disk Drive Troubleshooting Troubleshooting software related issues Troubleshooting software related issues The C: drive contains the Windows operating system software and the X-Series software. Boot problems can be caused by either a failure of the Windows operating system or the X-Series software. The failure could have occurred due to a failed installation procedure, X-Series software update failure or a virus.
  • Page 294: Reloading The X-Series Software

    CPU/Disk Drive Troubleshooting Reloading the X-Series Software Reloading the X-Series Software The X-Series software contains all the required components for the signal analyzer application as well as all software options. If the X-Series software has become corrupt the Windows operating system will boot but the X-Series software application will fail to start.
  • Page 295: Disk Drive Recovery Process

    CPU/Disk Drive Troubleshooting Disk Drive Recovery Process Disk Drive Recovery Process The Keysight Recovery System can be used to repair errors on the instrument's C: drive partition or to restore the original factory configuration of the system software. The Keysight Recovery System is stored in a separate hidden hard disk drive partition.
  • Page 296: Replacing The Instrument Disk Drive

    Step Notes 1. Make sure the instrument is turned off. 2. Turn on the instrument. After the Keysight Technologies screen is displayed, — Press the down arrow key to move the This screen is displayed for five seconds. highlight to Keysight Recovery...
  • Page 297: 10 Power Supply/Midplane Troubleshooting

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide 10 Power Supply/Midplane Troubleshooting What You Will Find in This Chapter The following information is presented in this chapter: 1. Theory of operation of the Power Supply/Midplane section. 2. Isolating the cause of a hardware problem by verifying the functionality of assemblies in the Power Supply and Midplane sections.
  • Page 298: A6 Power Supply Description

    Power Supply/Midplane Troubleshooting A6 Power Supply Description A6 Power Supply Description Purpose The A6 Power Supply assembly provides most all the necessary DC voltages for the entire PXA signal analyzer to operate correctly. If any of the power supplies are not within their operating voltages, the analyzer will not function properly.
  • Page 299: Power Supply Theory Of Operation

    Power Supply/Midplane Troubleshooting A6 Power Supply Description Power Supply Theory of Operation The A6 Power Supply assembly is serviced as an assembly only; no component level repair is supported. The A6 Power Supply assembly provides most all of the necessary DC voltages for the PXA.
  • Page 300 Power Supply/Midplane Troubleshooting A6 Power Supply Description Control Inputs There are a number of control inputs for the A6 Power Supply assembly. The ones that you will want to be familiar with are: POWER_ON_L is a signal that when pulled low tells the A6 Power Supply assembly to turn on all of its outputs.
  • Page 301 Power Supply/Midplane Troubleshooting A6 Power Supply Description Over Current Protection The A6 Power Supply assembly has built in over current protection that will shut down the supply if current draw from the instrument is too great. The power supply will remain on in over current state for a minimum of 1 second. The power supply shall turn off no later than 5 seconds after the beginning of the over current state.
  • Page 302: A6 Power Supply Assembly Troubleshooting

    Power Supply/Midplane Troubleshooting A6 Power Supply Assembly Troubleshooting A6 Power Supply Assembly Troubleshooting The A6 Power Supply assembly is serviced as an assembly only; no component level repair is supported. The A6 Power Supply has no user replaceable fuse. While there is a fuse internal to the supply this is not meant for field replacement.
  • Page 303: Control Inputs

    Power Supply/Midplane Troubleshooting A6 Power Supply Assembly Troubleshooting Control Inputs POWER_ON POWER_ON is a signal that when pulled low tells the A6 Power Supply assembly to turn on all of its outputs. This signal comes from the A4 Processor board assembly and is initiated by pressing the front panel power button.
  • Page 304 Power Supply/Midplane Troubleshooting A6 Power Supply Assembly Troubleshooting temperature condition. However, there is no way to know at the A6 Power Supply assembly level which one of these conditions may be the cause of a TTL low level to be on the FAULT_L status output. While any over voltage or over temperature conditions will most likely be caused by an A6 Power Supply assembly failure, an over current condition will most likely be caused by another assembly in...
  • Page 305: A7 Midplane Board Assembly Description

    Power Supply/Midplane Troubleshooting A7 Midplane Board Assembly Description A7 Midplane Board Assembly Description The A7 Midplane board assembly is used to connect the A4 Processor board assembly and the A6 Power Supply assembly to the A8 Motherboard, and thus the rest of the instrument electrical assemblies. In addition, the A7 Midplane board also provides the following functions: —...
  • Page 306: Midplane Board Connections

    Power Supply/Midplane Troubleshooting A7 Midplane Board Assembly Description Midplane Board Connections Connector Connects To Connector Connects To J101 A6 Power Supply Assembly J111 A6 Power Supply Assembly J102 A6 Power Supply Assembly J112 A6 Power Supply Assembly J103 A6 Power Supply Assembly J201 A4 Processor Assembly J104...
  • Page 307 Power Supply/Midplane Troubleshooting A7 Midplane Board Assembly Description Figure 10-2 A7 Midplane Board Assembly Connections N9030A PXA Signal Analyzer Service Guide...
  • Page 308: A7 Midplane Board Assembly Troubleshooting

    Power Supply/Midplane Troubleshooting A7 Midplane Board Assembly Troubleshooting A7 Midplane Board Assembly Troubleshooting The A7 Midplane board assembly is serviced as an assembly only; no component level repair is supported. Instrument Power Supply LEDs and Test Points While the A6 Power Supply assembly has no user accessible LEDs or test points the A7 Midplane board assembly does provide these for all of the different instrument power supplies as well as many of the power supply status lines.
  • Page 309 Power Supply/Midplane Troubleshooting A7 Midplane Board Assembly Troubleshooting Table 10-1 A7 Midplane Board LEDs and Test Points Supply/ Description Referenced Generated Expected Status Signal Power On Power Off Test Point Test Point (VDC) (VDC) +32VA +32 Volt ACOM +32 ± 2.0 Analog Supply +15VA +15 Volt...
  • Page 310 Power Supply/Midplane Troubleshooting A7 Midplane Board Assembly Troubleshooting Table 10-1 A7 Midplane Board LEDs and Test Points Supply/ Description Referenced Generated Expected Status Signal Power On Power Off Test Point Test Point (VDC) (VDC) POWER_OK Digital Supplies OK DCOM TTL Low TTL High POWER_ON_L Power Supply Enable...
  • Page 311 Power Supply/Midplane Troubleshooting A7 Midplane Board Assembly Troubleshooting Figure 10-3 A7 Midplane Board Assembly LEDs and Test Points N9030A PXA Signal Analyzer Service Guide...
  • Page 312 Power Supply/Midplane Troubleshooting A7 Midplane Board Assembly Troubleshooting N9030A PXA Signal Analyzer Service Guide...
  • Page 313: 11 Front Panel/Motherboard Troubleshooting

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide 11 Front Panel/Motherboard Troubleshooting What You Will Find in This Chapter The following information is found in this chapter: 1. Theory of operation of the Motherboard Assembly. 2. Theory of operation of the Front Panel Assembly.
  • Page 314: A8 Motherboard Description

    Front Panel/Motherboard Troubleshooting A8 Motherboard Description A8 Motherboard Description Purpose The Motherboard is an electrical link between many of the electrical assemblies in the instrument. The main functions of this PC board include: — Distribute power — Control and common signals between all the measurement PC boards including the A7 Midplane and the Front Panel Assembly —...
  • Page 315 Front Panel/Motherboard Troubleshooting A8 Motherboard Description The Motherboard is horizontally mounted, located near the bottom of the analyzer. Figure 11-2 Motherboard Connectors N9030A PXA Signal Analyzer Service Guide...
  • Page 316: A8 Motherboard Troubleshooting

    Front Panel/Motherboard Troubleshooting A8 Motherboard Description Motherboard What Plugs In? Motherboard What Plugs In? Connector Connector A7, Midplane A16, Reference A7, Midplane J31/J32 Option Slots A7, Midplane J41/J42 Option Slots A7, Midplane J51/J52 Option Slots B3, Fan J61/J62 Option Slots B2, Fan J71/J72 Option Slots...
  • Page 317: A1 Front Panel Assembly

    Front Panel/Motherboard Troubleshooting A1 Front Panel Assembly A1 Front Panel Assembly The major components of the A1 Front Frame Assembly are the A1A2 Front Panel Interface Board, A1A3 LCD, A1A4 LCD Inverter Board/DC-DC Converter, and the A1A5 Front Panel USB Interface Board, all of which are serviceable as individual components.
  • Page 318 Front Panel/Motherboard Troubleshooting A1 Front Panel Assembly N9030A PXA Signal Analyzer Service Guide...
  • Page 319: 12 Hardware Options

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide 12 Hardware Options What You Will Find in This Chapter The following information is found in this chapter. A25 Wideband Analog IF and A26 Digital IF Troubleshooting on page 322 Option BBA Analog I/Q Baseband Inputs Description on page 328...
  • Page 320 Hardware Options What You Will Find in This Chapter Table 12-1 Hardware Options Option Description Add itional Hard ware or Service Guide Section License Only Arbitrary IF Output License Only Chapter 6, “Front End (10 MHz to 75 MHz programmable, Control Troubleshooting.”...
  • Page 321 Hardware Options What You Will Find in This Chapter Table 12-1 Hardware Options Option Description Add itional Hard ware or Service Guide Section License Only Preamp, 100 kHz to 13.6 GHz License Only Chapter 4, “RF Section Troubleshooting (RF/Microwave Analyzers).” Preamp, 100 kHz to 26.5 GHz License Only Chapter 4, “RF Section...
  • Page 322: A25 Wideband Analog If And A26 Digital If Troubleshooting

    Hardware Options A25 Wideband Analog IF and A26 Digital IF Troubleshooting A25 Wideband Analog IF and A26 Digital IF Troubleshooting A25 Wideband Analog IF Assembly Description The analyzer's RF input signal is down converted to a 300 MHz intermediate frequency by the A13 Front End assembly and routed through the A15 Front End controller to A15J901.
  • Page 323 Hardware Options A25 Wideband Analog IF and A26 Digital IF Troubleshooting Figure 12-1 Analog IF Block Diagram N9030A PXA Signal Analyzer Service Guide...
  • Page 324: A25 Wideband Analog If Assembly Theory Of Operation

    Hardware Options A25 Wideband Analog IF and A26 Digital IF Troubleshooting Inputs to the A25 Assembly A25J101 300 MHz IF signal (from A15J901 Front End Controller) A25J301 2400 MHz reference from A16 Reference Assembly via W34 cable A25J805 Step Calibrator from A3J17 40 MHz Digital IF via W45 cable Outputs from the A25 Assembly A25J302 2400 MHz Reference Out A25J102 250 MHz IF Out to A3J15 of the 40 MHz Digital IF...
  • Page 325: A25 Wideband Troubleshooting

    Hardware Options A25 Wideband Analog IF and A26 Digital IF Troubleshooting A25 Wideband Troubleshooting Verify the 300 MHz IF Input level 1. Turn the instrument off. 2. Remove the instrument cover. Refer to Chapter 16, “Assembly Replacement Procedures” in this service guide. 3.
  • Page 326 Hardware Options A25 Wideband Analog IF and A26 Digital IF Troubleshooting Verify the 2400 MHz Frequency Reference 1. Turn the instrument off. 2. Remove the instrument cover. Refer to Chapter 16, “Assembly Replacement Procedures” in this service guide. 3. Turn on the N9030A Signal Analyzer and wait for the instrument to complete the boot up process.
  • Page 327: A26 140 Mhz Wideband Digital If Troubleshooting

    Hardware Options A25 Wideband Analog IF and A26 Digital IF Troubleshooting A26 140 MHz Wideband Digital IF Troubleshooting Verify the 300 MHz IF Input level The A26 Digital IF has a single accessible input at A25J2. It is not advisable to disconnect this cable and make measurements.
  • Page 328: Option Bba Analog I/Q Baseband Inputs Description

    Hardware Options Option BBA Analog I/Q Baseband Inputs Description Option BBA Analog I/Q Baseband Inputs Description The Analog Baseband I/Q inputs is a hardware option for the N9030A, Signal Analyzer. The option can be ordered at the time of sale as N9030A-BBA or as a post-sale upgrade as N9030AK-BBA.
  • Page 329: A19 Bbiq Main Board

    Hardware Options Option BBA Analog I/Q Baseband Inputs Description — Shields are on the board to minimize spurious responses. A19 BBIQ Main Board — Provides probe power to the BBIQ Interface board — Power Supply filtering and regulation — Contains FPGA (field programmable gate arrays) —...
  • Page 330 Hardware Options Option BBA Analog I/Q Baseband Inputs Description N9030A PXA Signal Analyzer Service Guide...
  • Page 331: What You Will Find In This Chapter

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide 13 Block Diagrams What You Will Find in This Chapter The following sections are found in this chapter: RF Lowband Path Block Diagram RF Highband Path #1 Block Diagram RF Highband Path #2 Block Diagram...
  • Page 332: Block Diagrams

    Block Diagrams Block Diagrams Block Diagrams N9030A PXA Signal Analyzer Service Guide...
  • Page 333 PXA RF BLOCK DIAGRAM (Options 503, 508, 513, 526) (Lowband Path - Input signals 3 Hz to 3.599 GHz) A15 FRONT END CONTROLLER J800 ATTENUATOR CONTROL J802 LOW BAND SWITCH BYPASS CONTROL J700 LOW BAND SWITCH CONTROL (Option MPB) (Option MPB) J801 PRESELECTOR BYPASS CONTROL 6 dB...
  • Page 334 PXA RF BLOCK DIAGRAM (Options 508, 513, 526) (Highband Path #1 - Input signals 3.6 to 13.6 GHz) A15 FRONT END CONTROLLER J800 ATTENUATOR CONTROL J802 LOW BAND SWITCH BYPASS CONTROL J700 LOW BAND SWITCH CONTROL (Option MPB) (Option MPB) J801 PRESELECTOR BYPASS CONTROL 6 dB...
  • Page 335 PXA RF BLOCK DIAGRAM (Option 526) (Highband Path #2 - Input signals 13.6 GHz to 26.5 GHz) A15 FRONT END CONTROLLER J800 ATTENUATOR CONTROL J802 LOW BAND SWITCH BYPASS CONTROL J700 LOW BAND SWITCH CONTROL (Option MPB) (Option MPB) J801 PRESELECTOR BYPASS CONTROL 6 dB J300...
  • Page 336 OPTION 543, 544, 550 mmW PXA RF BLOCK DIAGRAM (Lowband Path - Input signals 3 Hz to 3.599 GHz) A15 FRONT END CONTROLLER J800 ATTENUATOR CONTROL J802 LOW BAND SWITCH BYPASS CONTROL J700 LOW BAND SWITCH CONTROL SWITCH 4 (Option MPB) J801 PRESELECTOR BYPASS CONTROL J300...
  • Page 337 OPTION 543, 544, 550 mmW PXA RF BLOCK DIAGRAM (Highband Path #1 - Input signals 3.6 to 17.1 GHz) A15 FRONT END CONTROLLER J800 ATTENUATOR CONTROL J802 LOW BAND SWITCH BYPASS CONTROL J700 LOW BAND SWITCH CONTROL SWITCH 4 (Option MPB) J801 PRESELECTOR BYPASS CONTROL J300...
  • Page 338 OPTION 543, 544, 550 mmW PXA RF BLOCK DIAGRAM (Highband Path #2 - Input signals 17.1 to 34.5 GHz) A15 FRONT END CONTROLLER J800 ATTENUATOR CONTROL J802 LOW BAND SWITCH BYPASS CONTROL J700 LOW BAND SWITCH CONTROL SWITCH 4 (Option MPB) J801 PRESELECTOR BYPASS CONTROL J300...
  • Page 339 OPTION 543, 544, 550 mmW PXA RF BLOCK DIAGRAM (Highband Path #3 - Input signals 34.5 to 50 GHz) A15 FRONT END CONTROLLER J800 ATTENUATOR CONTROL J802 LOW BAND SWITCH BYPASS CONTROL J700 LOW BAND SWITCH CONTROL SWITCH 4 (Option MPB) J801 PRESELECTOR BYPASS CONTROL J300...
  • Page 340 A13A1 Front End A20 YTO To Mixer 1 A16 REFERENCE A14 LO SYNTHESIZER 3.8 TO 8.73 GHz DISTRIBUTION A16A1 REFERENCE DAUGHTER MAIN LOOP Card Cage To Mixer 2 Connector Pretune 4.8 GHz DRIVER and Mixer 3 FPGA (from A8) +10 dBm J702 +11 dBm Serial Bus &...
  • Page 341: Analog If Block Diagram

    Block Diagrams Block Diagrams Analog IF Block Diagram N9030A PXA Signal Analyzer Service Guide...
  • Page 342: Digital If Block Diagram

    Block Diagrams Block Diagrams Digital IF Block Diagram N9030A PXA Signal Analyzer Service Guide...
  • Page 343: Pxa Computer Block Diagram

    Block Diagrams Block Diagrams PXA Computer Block Diagram N9030A PXA Signal Analyzer Service Guide...
  • Page 344 Block Diagrams Block Diagrams N9030A PXA Signal Analyzer Service Guide...
  • Page 345: 14 Service And Diagnostics Menus

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide 14 Service and Diagnostics Menus Overview The Service capabilities described below are accessed via the Service and Diagnostic menus in the System menu. The Service capabilities are intended for field service technicians. These technicians may be at an Keysight Service Center or at a self-maintaining customer site.
  • Page 346: Secure Service Access

    Service and Diagnostics Menus Overview Secure service access To access the secure service capabilities press System, More, Service with the instrument application running. At this point you will see the window shown in Figure 14-1. Enter the Service Code and press Enter. The Service Code is: -2061 Figure 14-1 Service Code Entry...
  • Page 347: Menus

    Menus This menu is only Timebase Service available on the Factory (in System menu) Image or with specific Timebase DAC logins, some logins † 1960 require a Service Guide for entry Save Service Service Service Diagnostics Timebase Diagnostics LO Bandlock Lock Funcs Corrections Corrections...
  • Page 348 Service and Diagnostics Menus Menus Service Alignments Align Diagnostics Visible Align Diagnostics Subsystem Subsystem Align Log... Align Log Mode Clear Append Current IF Current Flatness System Gain Phase Noise Adjustment N9030A PXA Signal Analyzer Service Guide...
  • Page 349 Service and Diagnostics Menus Menus Service Diagnostics Diagnostics Show Show Software Software N9030A PXA Signal Analyzer Service Guide...
  • Page 350 Service and Diagnostics Menus Menus Diagnostics (in System menu) Diagnostics Show Hardware Show Hardware Statistics Statistics screen N9030A PXA Signal Analyzer Service Guide...
  • Page 351 Service and Diagnostics Menus Menus Figure 14-2 Hardware Statistical Information N9030A PXA Signal Analyzer Service Guide...
  • Page 352: Service Key Descriptions

    Service and Diagnostics Menus Service Key Descriptions Service Key Descriptions Timebase Allows the technician to adjust the 10 MHz reference (“timebase”) manually. If the Timebase DAC value has been changed, but no Save operation performed before exiting this menu, a warning is provided to the user that they have not saved their setting: Timebase DAC Allows the technician the ability to adjust the 10 MHz reference (“timebase”).
  • Page 353: Corrections

    Service and Diagnostics Menus Service Key Descriptions Corrections The Corrections menu allows the technician to activate and deactivate specific amplitude correction sets. With this capability, the technician can determine if an anomaly is a result of raw hardware performance or incorrect correction data.
  • Page 354 Service and Diagnostics Menus Service Key Descriptions IF Flatness This function turns the corrections related to IF flatness On or Off. When IF Flatness is OFF, the Advisory Event “IF Flatness corrections OFF” will be displayed. When IF Flatness is ON, the Advisory Event “IF Flatness corrections OFF” will be cleared.
  • Page 355: Band Lock

    Service and Diagnostics Menus Service Key Descriptions Band Lock Provides the ability to tune the analyzer over as large a range as can be accommodated by the specified harmonic number and 1st LO frequency range. As a result, this feature can be used to check performance in the frequency band overlap regions.
  • Page 356: Lo Band Lock

    Service and Diagnostics Menus Service Key Descriptions LO Band Lock Provides the ability to tune the analyzer over as large a range as can be accommodated by the specified LO Band. As a result, this feature can be used to check performance in the LO band overlap regions. By definition, multi-band sweeps are not allowed.
  • Page 357: Low Noise Path

    Service and Diagnostics Menus Service Key Descriptions Low Noise Path Provides the ability to lock the Option (LNP) Low Noise Path switch that is used in the μWave Path Control menu into the ON position, regardless of the state of the μWave Path Control menu or functions.
  • Page 358: Align

    Service and Diagnostics Menus Service Key Descriptions Align The Align Menu allows accessing Diagnostic capabilities of Alignment, and invoking alignments for individual subsystems. Diagnostic The Diagnostic menu contains items for controlling the operating behavior of Alignment and the Alignment reporting capabilities. Visible Align Controls the state of Visible Align.
  • Page 359 Service and Diagnostics Menus Service Key Descriptions Immediately executes an alignment of the LO subsystem. The instrument will stop any measurement currently underway, perform the alignment, then restart the measurement from the beginning. A failure of LO will set the Error Condition “Align LO failed”. A failure will not employ new LO alignment data.
  • Page 360 Service and Diagnostics Menus Service Key Descriptions This is exactly the same as the customer accessible Align Now, RF with one exception: the alignment can be invoked even if a previous Align Now, All has not been executed (this key is not grayed-out if using default alignment data).
  • Page 361 Service and Diagnostics Menus Service Key Descriptions Diagnostics Pressing Diagnostics in the Service Menu brings up the Service Diagnostics submenu. The functions in this menu allow the technician to do more detailed, lower-level troubleshooting. Show Software The Show Software screen displays revision information for Keysight internal software that comprises the embedded application and programmable hardware devices (FPGAs and PLDs).
  • Page 362 Service and Diagnostics Menus Service Key Descriptions N9030A PXA Signal Analyzer Service Guide...
  • Page 363: 15 Replaceable Parts

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide 15 Replaceable Parts What You Will Find in This Chapter The following information is found in this chapter: 1. Part number tables for assemblies, mechanical parts, cables, front panel connectors, and labels.
  • Page 364 Replaceable Parts What You Will Find in This Chapter Figure 15-20, “Front Frame Parts (shields off) - LCD,” page 408 Figure 15-21, “Front Frame Parts - LED,” page 409 Figure 15-22, “Front Frame Parts (shields off) - LED,” page 410 Figure 15-23, “Front Frame Exploded View - LCD,”...
  • Page 365: How To Order Parts

    — Description of where the part is located, what it looks like, and its function (if known) — Quantity required For a list of Keysight Technologies sales and service office locations, refer to “Contacting Keysight Technologies” on page N9030A PXA Signal Analyzer Service Guide...
  • Page 366: Replaceable Parts

    Replaceable Parts Replaceable Parts Replaceable Parts Some of the assemblies listed in the following table are related to options that are available with the PXA Signal Analyzer. These options are described below. Table 15-1 All Replaceable Parts Reference Description Part Number Designator A1A1 N9030-60003...
  • Page 367 Replaceable Parts Replaceable Parts Table 15-1 All Replaceable Parts Reference Description Part Number Designator A1A5 Front Panel Daughter Board N9020-63193 A1MP1 Main Keypad E4410-40100 A1MP2 Display Keypad E4410-40101 A1MP3 Frequency Label, 3.6 GHz N9030-80003 A1MP4 Frequency Label, 8.4 GHz N9030-80004 A1MP5 Frequency Label, 13.6 GHz N9030-80005...
  • Page 368 Replaceable Parts Replaceable Parts Table 15-1 All Replaceable Parts Reference Description Part Number Designator A1W2 Cable Assembly, Front Panel Interface Board to Inverter Board Serial Number > MY49431900, > SG49430063, > US51160001 W1312-60130 Serial Number < MY49431900, < SG49430063, < US51160001 W1312-60113 A1W2 Grommet 0400-0333...
  • Page 369 Designator RF Attenuator B (0-66 dB) (Options 503, 508, 513, 526) 33321-60083 RF Attenuator B (0-60 dB) (Options 543, 544, 550) 33325-60020 Low Band Switch Assembly Option 503 E4410-60121 Options 508, 513, 526 E4410-60121 Options 543, 544, 550 N9020-60051 YTF Preselector (Options 503, 508, 513, 526)
  • Page 370 Replaceable Parts Replaceable Parts Table 15-1 All Replaceable Parts Reference Description Part Number Designator Reserved Reserved B1, B2, B3 3160-4199 Type-N Input Connector Assembly N9039-60030 (Options 503, 508, 513, 526 without Option C35) 3.5 mm Input Connector Assembly N9020-60196 (Option C35) 2.4 mm Input Connector Assembly N9030-60011 (Options 543, 544, 550)
  • Page 371 Replaceable Parts Replaceable Parts Table 15-1 All Replaceable Parts Reference Description Part Number Designator Cover, inner hole N9020-00041 Cover, hole N9020-00040 Bracket, Midplane W1312-00048 Bracket, Chassis Front W1312-00098 Bracket, Fan W1312-00118 Bracket, RF Side (right side outer) N9020-00014 Bracket, Attenuator (used for both attenuators) E4449-00103 (Options 503, 508, 513, 526) Bracket, Attenuator (used for both attenuators)
  • Page 372 Replaceable Parts Replaceable Parts Table 15-1 All Replaceable Parts Reference Description Part Number Designator Plug hole, Nylon for 0.25 hole (SMA size) 6960-0076 Plug hole, dome head, Nylon for 0.875 hole 6960-0177 Cable Tie, .062 - 2 dia, .045 wide 1400-0507 Fan Guard, Steel 3160-0281...
  • Page 373 Replaceable Parts Replaceable Parts Table 15-1 All Replaceable Parts Reference Description Part Number Designator Cable, semi-rigid, Front End assy J2 to Low Band Switch J2 N9020-20101 (Options 503, 508, 513, 526) Cable, semi-rigid, Front End assy J2 to Low Band Switch J2 N9020-20131 (Options 543, 544, 550) Reserved...
  • Page 374 Cable, semi-rigid, Front Panel Ext Mixer connector to W17 (Option EXM) N9020-20166 Cable, coax, Ext IF Out, A13J13 to Front End Control J903 8121-2027 (Option 503, 508, 513, 526) (Option EXM) Cable, coax, Ext IF Out, A13J13 to Front End Control J903 8121-2025 (Option 543, 544, 550) (Option EXM) Cable, semi-rigid, 4.8GHz 2nd LO.
  • Page 375 Replaceable Parts Replaceable Parts Table 15-1 All Replaceable Parts Reference Description Part Number Designator Cable, coax, Step Cal, Digital IF J17 to Reference board J726 8121-1401 (Required if no Option BIX) Cable, semi-rigid, Switched Filter In, A13A1 J10 to A13A2 J2 N9020-20079 (Options 503, 508, 513, 526) Cable, semi-rigid, Switched Filter In, A13A1 J10 to A13A2 J2...
  • Page 376 Does not include nameplate, See A1MP3 through A1 MP6 and A1MP20 through A1MP22. b. The E4410-60121 is the preferred replacement for the N9020-60255, Low Band Switch that may be installed in some N9030As with Option 503. c. Does not include A1A1MP20 or A1A1MP21 overlays.
  • Page 377 Table 15-2 Attaching Hardware Attach Part Number Type Tool Torque Analog IF Digital IF 0515-0372 M3 X 0.5 Torx T-10 9 inch-lbs (8 mm long) Attenuators Attenuator Bracket 2 per 0515-0372 M3 X 0.5 Torx T-10 9 inch-lbs (8 mm long) Attenuator Bracket Chassis 2 per...
  • Page 378 Table 15-2 Attaching Hardware Attach Part Number Type Tool Torque Display Bracket Front Frame 0515-0372 M3 X 0.5 Torx T-10 9 inch-lbs (8 mm long) Disk Drive Disk Drive Tray 0515-0372 M3 X 0.5 Torx T-10 9 inch-lbs (8 mm long) Disk Drive Handle Disk Drive Rear Panel 0515-1227...
  • Page 379 Table 15-2 Attaching Hardware Attach Part Number Type Tool Torque Front Panel Shield Front Frame 0515-0372 M3 X 0.5 Torx T-10 9 inch-lbs (8 mm long) LO Synthesizer Assembly Chassis 0515-1035 M3 X 0.5 Torx T-10 9 inch-lbs (8 mm long) Low Band Switch Assy.
  • Page 380 Table 15-2 Attaching Hardware Attach Part Number Type Tool Torque Rear Feet Rear Panel 0515-1619 M4 X 0.7 Torx T-20 21 inch-lbs (25 mm long) 3050-0893 Flat Washer Rear Frame Chassis 0515-0372 M3 X 0.5 Torx T-10 9 inch-lbs (8 mm long) Rear Frame Hole Cover Rear Frame Inner Hole Cover 0515-0372...
  • Page 381 Table 15-2 Attaching Hardware Attach Part Number Type Tool Torque YIG Tuned Filter Assembly Chassis 0515-0372 M3 X 0.5 Torx T-10 9 inch-lbs (8 mm long) YIG Tuned Oscillator Assembly Chassis 0515-0372 M3 X 0.5 Torx T-10 9 inch-lbs (8 mm long) YIG Tuned Oscillator Top YIG Tuned Oscillator 0515-0372...
  • Page 382: Hardware

    Replaceable Parts Hardware Hardware Figure 15-1 Major Assemblies Item Description Keysight Part Number A2 Analog IF Assembly N9020-60254 A3 Digital IF Assembly N9020-60016 A4 CPU Board (without A5 drive or drive tray parts, includes battery) Serial Prefix Number ≥ MY/SG/US5533 N9020-60135 Serial Prefix Number ≥...
  • Page 383 Replaceable Parts Hardware Item Description Keysight Part Number A19 BBIQ Main Board (Option BBA) N9020-60093 A14 Synthesizer Assembly N9020-60008 A15 Front End Controller N9020-60172 N9030A PXA Signal Analyzer Service Guide...
  • Page 384 Replaceable Parts Hardware Figure 15-2 External Hardware Item Description Keysight Part Number Strap Handle E8251-60067 1, 2 (includes screws) M4 X 0.7 (25 mm long) 0515-1619 Screw Rear Feet 5041-9611 Dress Cover W1312-00119 Bottom Feet 5041-9167 N9030A PXA Signal Analyzer Service Guide...
  • Page 385 Replaceable Parts Hardware Figure 15-3 CPU Assembly Item Description Keysight Part Number A4 CPU Board (without A5 drive or drive tray parts, includes battery) Serial Prefix Number ≥ MY/SG/US5533 N9020-60247 Serial Prefix Number ≥ MY/SG5136 and US5135 N9020-60135 Serial Prefix Number < MY/SG5136 and US5135 N9020-60081 A4BT1 Battery, CPU, 3V, LI Manganese Dioxide 1420-0356 (CR2032)
  • Page 386 Replaceable Parts Hardware Figure 15-4 Disk Drive Tray Assembly Item Description Keysight Part Number N9020-60125 Disk Drive A5MP1 W1312-40078 Disk Drive Tray A5MP2 W1312-00103 Disk Drive Rear Panel A5MP3 1440-0421 Disk Drive Assembly Handle Screw M3 x 0.5 (8 mm long) 0515-0372 Pan head 0515-1035 Flat head Screw M2.5 x 0.45 (5 mm long)
  • Page 387 Replaceable Parts Hardware Figure 15-5 Top Brace and Reference Bracket Item Description Keysight Part Number Top Brace Assembly (includes 4 each N9030-60005 Vibration Mounts 0460-2725) Bracket, Power Supply W1312-00131 M3 X 0.5 (8 mm long) 0515-0372 Screw M3 X 0.5 (6 mm long) 0515-1227 Screw M3 X 0.5 (8 mm long)
  • Page 388 Replaceable Parts Hardware Figure 15-6 RF Area (Options 503, 508, 513, 526) N9030A PXA Signal Analyzer Service Guide...
  • Page 389 Replaceable Parts Hardware Item Description Keysight Part Number A9 RF Attenuator A (0-4 dB) (Options 503, 508, 513, 526) 33360-60008 A10 RF Attenuator B (0-66 dB) (Options 503, 508, 513, 526) 33321-60083 A11 Low Band Switch Assembly E4410-60121 A12 YTF Preselector (Options 503, 508, 513, 526) N9020-60229 A20 YTO Assembly N9020-60009...
  • Page 390 Replaceable Parts Hardware Figure 15-7 RF Area (Options 543, 544, 550) N9030A PXA Signal Analyzer Service Guide...
  • Page 391 Replaceable Parts Hardware Item Description Keysight Part Number A9 RF Attenuator A (0-10 dB) (Options 543, 544, 550) 33326-60013 A10 RF Attenuator B (0-60 dB) (Options 543, 544, 550) 33325-60020 A11 Options 543, 544, 550 N9020-60051 A12 YTF Preselector (Options 543, 544, 550) N9030-60024 A20 YTO Assembly N9020-60009...
  • Page 392 Replaceable Parts Hardware Figure 15-8 Front End Parts (Options 503, 508, 513, 526) Item Description Keysight Part Number A13 Front End Assembly (Options 503, 508, 513, 526) Serial N9020-60143 Prefix Numbers ≥ MY/SG/US5235 Type-N Input Connector Assembly (Options 503, 508, 513, 526 N9039-60030 without Option C35) Cable, IF Out from Front End Assy J7 to Front End Control J902...
  • Page 393 Replaceable Parts Hardware Item Description Keysight Part Number Cable, semi-rigid, Switched Filter In, A13A1 J10 to A13A2 J2 N9020-20079 (Options 503, 508, 513, 526) Cable, semi-rigid, Switched Filter Out, A13A2 J5 to A13A1 J11 N9020-20078 (Options 503, 508, 513, 526) N9030A PXA Signal Analyzer Service Guide...
  • Page 394 Replaceable Parts Hardware Figure 15-9 Front End Parts (Options 543, 544, 550) Item Description Keysight Part Number A13 Front End Assembly (Options 503, 508, 513, 526) Serial N9020-60173 Prefix Numbers < MY/SG/US5235 2.4 mm Input Connector Assembly (Options 543, 544, 550) N9030-60011 Cable, IF Out from Front End Assy J7 to Front End Control J902 8121-1862...
  • Page 395 Replaceable Parts Hardware Item Description Keysight Part Number Cable, semi-rigid, Switched Filter Out, A13A2 J5 to A13A1 J11 N9020-20110 (Options 543, 544, 550) Cable, semi-rigid, YTF output to Front End assy J9 (Options N9010-20006 543, 544, 550 without Option MPB or LNP) Cable, semi-rigid, Delay Line, A13A2 Switched Filter J3 to J4 N9020-20080 N9030A PXA Signal Analyzer Service Guide...
  • Page 396 Replaceable Parts Hardware Figure 15-10 Front End Cables Item Description Keysight Part Number A15 Front End Controller N9020-60172 A14 Synthesizer Assembly N9020-60008 Cable, Ribbon, Attenuator A/B to Front End Controller J800 E4410-60157 Cable, ribbon, Lowband Switch J4 to Front End Controller J700 N9020-60092 Cable, wire harness, YTF Control, Front End Controller J300 to N9020-60059...
  • Page 397 Replaceable Parts Hardware Item Description Keysight Part Number Cable, coax, 100 MHz, Reference Assy J706 to LO Synthesizer 8121-1401 Cable, ribbon, Low Band Switch Bypass Control. Switch 3 to A15 N9020-60087 Front End Controller J802 (Options 503, 508, 513, 526 with Option LNP or MPB) N9020-60177 Cable, ribbon, Low Band Switch Bypass Control.
  • Page 398 Replaceable Parts Hardware Figure 15-11 Reference Board Cables Item Description Keysight Part Number A16 Reference Assembly (includes associated shields) N9020-60188 Cable, semi-rigid, Cal In to attenuator, Reference Assy J701 to N9020-20023 Attenuator A (Options 503, 508, 513, 526) Cable, semi-rigid, Cal In to attenuator, Reference Assy J701 to N9020-20072 Attenuator A (Options 543, 544, 550) Cable, semi-rigid, 2nd LO In, Reference Assy J702 to Front...
  • Page 399 Replaceable Parts Hardware Figure 15-12 AIF Cables Figure 15-13 DIF Cables N9030A PXA Signal Analyzer Service Guide...
  • Page 400 Replaceable Parts Hardware Item Description Keysight Part Number Cable, coax, Wideband IF Out, Front End Controller J901 to 8121-1919 Digital IF J15 (instruments without Option B1X) Cable, coax, 300 MHz, Reference Assy J711 to Analog IF J300 8121-1861 Cable, coax, 250 MHz from Wideband A-IF J102 to Digital IF 8121-1401 J15 (Option B1X) Cable, coax, 22.5 MHz IF Out, Analog IF J601 to D-IF J19...
  • Page 401 Replaceable Parts Hardware Figure 15-14 AIF/DIF Assemblies Item Description Keysight Part Number A2 Analog IF Assembly N9020-60254 A3 Digital IF Assembly N9020-60016 M3 X 0.5 (8 mm long) 0515-0372 Screw, Cable, ribbon interconnect from Analog IF J820 to N9020-60046 Digital IF A3J30 A3W1 Cable Assembly, Smart Noise Source (Wire Harness) N9020-60090...
  • Page 402 Replaceable Parts Hardware Figure 15-15 Motherboard Item Description Keysight Part Number A8 Motherboard Assembly N9030-63002 M3 X0.5 (8 mm long) 0515-0372 Screw N9030A PXA Signal Analyzer Service Guide...
  • Page 403 Replaceable Parts Hardware Figure 15-16 Chassis N9030A PXA Signal Analyzer Service Guide...
  • Page 404 Replaceable Parts Hardware Item Description Keysight Part Number Chassis Base N9020-00015 Chassis Side, Right (inner) W1312-00116 Chassis Side, Left (inner) W1312-00117 Bracket, Midplane W1312-00048 Bracket, Chassis Front W1312-00098 Bracket, Fan W1312-00118 Bracket, RF Side (right side outer) N9020-00014 Rear Frame N9030-00001 Bracket, Attenuator (used for both attenuators) E4449-00103...
  • Page 405 Replaceable Parts Hardware Figure 15-17 Fan Hardware Item Description Keysight Part Number 3160-4199 B1, B2, B3 Fan Guard, Steel 3160-0281 Rivet, Fan Mounting 0361-1272 N9030A PXA Signal Analyzer Service Guide...
  • Page 406 Replaceable Parts Hardware Figure 15-18 Input Connector Item Description Keysight Part Number M3 X 0.5 (8 mm long) 0515-0372 Screw J1 Type-N Input Connector Assembly (Options 503, 508, 513, 526 N9039-60030 without Option C35) N9020-60196 J1 3.5 mm Input Connector Assembly (Option C35) N9030-60011 J1 2.4 mm Input Connector Assembly (Options 543, 544, 550) Cable, semi-rigid, RF Input to Attenuator A (Options 503, 508, 513,...
  • Page 407 Replaceable Parts Hardware Figure 15-19 Front Frame Parts - LCD Item Description Keysight Part Number A1A5 Front Panel Daughter Board N9020-63193 A1MP14 Display Bracket W1312-00115 A1MP10-13 Cable Clamp (Front Panel Cables) 1400-1439 A1MP18 and A1MP19 Shield, Front Panel N9020-00051 A1W2 Cable Assembly, Front Panel Interface W1312-60113 Board to Inverter Board A1MP16 Inverter Shield Top...
  • Page 408 Replaceable Parts Hardware Figure 15-20 Front Frame Parts (shields off) - LCD Item Description Keysight Part Number A1MP14 Display Bracket W1312-00115 A1A2MP2 Speaker Foam W1312-40088 A1A2MP1 Speaker 9164-0453 A1A2 Front Panel Interface Board W1312-63092 A1A5 Front Panel Daughter Board N9020-63193 A1W1 Flex Circuit, Display to Front Panel Interface Board W1312-60010 A1MP10-13 Cable Clamp (Front Panel Cables)
  • Page 409 Replaceable Parts Hardware Figure 15-21 Front Frame Parts - LED Item Description Keysight Part Number A1MP14 Display Bracket W1312-00145 A1MP18 and A1MP19 Shield, Front Panel N9020-00051 A1A5 Front Panel Daughter Board N9020-63193 M3 X 0.5 (8 mm long) 0515-0372 Screw N9030A PXA Signal Analyzer Service Guide...
  • Page 410 Replaceable Parts Hardware Figure 15-22 Front Frame Parts (shields off) - LED Item Description Keysight Part Number A1A2 Front Panel Interface Board W1312-63092 A1A2MP1 Speaker 9164-0453 A1A2MP2 Speaker Foam W1312-40088 A1W1 Flex Circuit, Display to Front Panel Interface Board W1312-60122 A1W2 Cable Assembly, Front Panel Interface Board to W1312-60130 Inverter Board...
  • Page 411 Replaceable Parts Hardware Figure 15-23 Front Frame Exploded View - LCD N9030A PXA Signal Analyzer Service Guide...
  • Page 412 Replaceable Parts Hardware Item Description Keysight Part Number Front Frame Front Frame Side Trim Strip (plastic) W1312-40005 Front Frame Side Trim Strip (vinyl) 5041-9172 Main Keyboard Overlay N9030-80011 A1MP9 RPG Knob W1312-40017 A1MP3 Frequency Label, 3.6 GHz N9030-80003 A1MP4 Frequency Label, 8.4 GHz N9030-80004 A1MP5 Frequency Label, 13.6 GHz N9030-80005...
  • Page 413 Replaceable Parts Hardware Item Description Keysight Part Number A1MP15 Inverter Board Shield W1312-00024 A1MP16 Inverter Shield Top N9020-00010 A18 BBIQ Interface Board (Option BBA) N9020-60094 A17 BBIQ LED Board (Option BBA) N9020-63095 a. Non-orderable item, see A1A1. N9030A PXA Signal Analyzer Service Guide...
  • Page 414 Replaceable Parts Hardware Figure 15-24 Front Frame Exploded View - LED N9030A PXA Signal Analyzer Service Guide...
  • Page 415 Replaceable Parts Hardware Item Description Keysight Part Number Front Frame Main Keyboard Overlay N9030-80011 Overlay, Left Display E4410-80109 Cover Plate N9020-00002 Front Frame Side Trim Strip (plastic) W1312-40005 Front Frame Ground Spring W1312-00021 A1A2 Front Panel Interface Board W1312-63092 A1A2MP1 Speaker 9164-0453 A1A2MP2 Speaker Foam W1312-40088...
  • Page 416 Replaceable Parts Hardware N9030A PXA Signal Analyzer Service Guide...
  • Page 417: 16 Assembly Replacement Procedures

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide 16 Assembly Replacement Procedures What You Will Find in This Chapter Procedures in this chapter enable you to locate, remove, and replace the following major assemblies in your instrument. Refer to Chapter 15, “Replaceable Parts.”...
  • Page 418 Assembly Replacement Procedures What You Will Find in This Chapter Front Frame Assembly on page 522 Inverter Board Assembly on page 529 Display Assembly - LCD on page 530 Display Assembly - LED on page 538 Daughter Board, Interface Board and Keypad on page 532 page 540 N9030A PXA Signal Analyzer Service Guide...
  • Page 419: Before Starting

    Assembly Replacement Procedures What You Will Find in This Chapter Before Starting Before starting to disassemble the instrument: • Check that you are familiar with the safety symbols marked on the instrument. And, read the general safety considerations and the safety note definitions given in the front of this guide.
  • Page 420: Tools You Will Need

    Assembly Replacement Procedures Tools you will need Tools you will need Figure 16-1 TORX Tool Description Keysight Part Number TORX Hand Driver - Size T-8 8710-1614 TORX Hand Driver - Size T-10 8710-1623 TORX Hand Driver - Size T-20 8710-1615 9/16 inch nut driver 8720-0008 1/4 inch nut driver...
  • Page 421: Major Assembly Locations

    Assembly Replacement Procedures Major Assembly Locations Major Assembly Locations Figure 16-2 Major Assemblies Item Description A2 Analog IF Assembly A3 Digital IF Assembly CPU Assembly A6 Power Supply A7 Midplane Assembly A16 Reference Assembly (includes associated shields) A25 Wideband Analog IF (Option B1X) A26 Wideband Digital IF (Option B1X) A19 BBIQ Main Board (Option BBA) A14 Synthesizer Assembly...
  • Page 422: Instrument Outer Case

    Assembly Replacement Procedures Instrument Outer Case Instrument Outer Case If the instrument is placed on its face during any of the following procedures, be sure to use a soft surface or soft cloth to avoid damage to the front panel, keys, or input connector. Removal 1.
  • Page 423: Replacement

    Assembly Replacement Procedures Instrument Outer Case Figure 16-3 Instrument Outer Case Removal Replacement 1. Disconnect the instrument from ac power. 2. Slide the instrument cover back onto the deck from the rear. The seam on the cover should be on the bottom. Be sure the cover seats into the gasket groove in the Front Frame Assembly.
  • Page 424: Top Brace And Power Supply Bracket

    Assembly Replacement Procedures Top Brace and Power Supply Bracket Top Brace and Power Supply Bracket Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Refer to Figure 16-4. To remove the top brace (1), use the T-10 driver to remove the twelve screws (3) (0515-0372) attaching the top brace to the chassis.
  • Page 425 Assembly Replacement Procedures Top Brace and Power Supply Bracket Figure 16-5 Wire Hold Downs Replacement 1. Refer to Figure 16-4. To replace the top brace or the power supply bracket, place them into the correct position and attach the screws referred to in the removal process.
  • Page 426: Rf Area (Options 503, 508, 513, 526)

    Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) RF Area (Options 503, 508, 513, 526) Refer to Figure 16-6. The RF area consists of RF attenuator A (1), RF attenuator B (2), low band switch assembly (3), YTF Preselector (4), and YTO (5).
  • Page 427 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 3. Refer to Figure 16-7. Remove the RF bracket (1) by removing the sixteen screws (2) (0515-0372) using the T-10 driver. Figure 16-7 RF Bracket Removal N9030A PXA Signal Analyzer Service Guide...
  • Page 428: Attenuators

    Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Attenuators Removal 1. Refer to Figure 16-8. To remove Attenuator A (1) or Attenuator B (2), remove the semi-rigid cables W2, W3, W4, or W6 attached to the attenuator using the 5/16 inch wrench. 2.
  • Page 429 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Figure 16-8 Attenuators Removal Item Keysight Part Number N9020-20100 N9020-20023 N9020-20025 N9020-20024 N9030A PXA Signal Analyzer Service Guide...
  • Page 430 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Replacement 1. Refer to Figure 16-8. Position the attenuator in the bracket so that the ribbon connector end is “up”. 2. Replace the two screws (0515-0372) that attach the attenuator to the bracket.
  • Page 431: Low Band Switch

    Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Low Band Switch Removal If the analyzer has hardware for Options MPB and LNP installed, perform the removal procedure for Options MPB and LNP on page 439 first. 1. Refer to Figure 16-9.
  • Page 432 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Figure 16-10 Low Band Switch Bracket Removal Figure 16-11 Low Band Switch and Bracket Separation N9030A PXA Signal Analyzer Service Guide...
  • Page 433 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Replacement 1. Refer to Figure 16-11. Place the switch onto the bracket and replace the four screws (3) (0515-0372). Torque to 9 inch-pounds in the sequence shown, starting with #1. 2.
  • Page 434: Ytf Preselector

    Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) YTF Preselector Removal 1. Refer to Figure 16-12. Remove cables W2, W56 and W57 from the YTF Preselector (1). 2. Remove the wire harness W11. 3. Refer to Figure 16-13. From the bottom of the instrument, remove the four screws (1) (0515-0372).
  • Page 435 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Figure 16-13 YTF Preselector Screws N9030A PXA Signal Analyzer Service Guide...
  • Page 436 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Replacement 1. Inspect the chassis where the YTF Preselector mounts and remove the gap pad if present (see Figure 16-14, item (1)). The gap pad may remain attached to the faulty YTF Preselector. 2.
  • Page 437: Yto

    Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Removal 1. Refer to Figure 16-15. Remove cable W20 from the YTO (1). 2. Remove cable W4. 3. Remove the ribbon cable W23 by pulling forward on the locking latch. 4.
  • Page 438 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Figure 16-16 YTO Screws Replacement 1. Refer to Figure 16-16. Place the YTO into the chassis. Replace the two screws (1) (0515-0372). Torque to 9 inch-pounds. Figure 16-15. Replace the cables W4 and W20. Torque to 10 inch-pounds. 3.
  • Page 439: Options Mpb And Lnp

    Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Options MPB and LNP Removal 1. Refer to Figure 16-17. Remove rigid cable (N9020-20143) (1) from top switch port 1 to Attenuator B output. Figure 16-17 W51 Cable Removal N9030A PXA Signal Analyzer Service Guide...
  • Page 440 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 2. Refer to Figure 16-18. Remove cable (E4410-20163) (3) from middle switch port 2 to YTF Assembly. 3. Remove cable (E4410-20165) (2) from bottom switch port 2 to YTF Assembly. 4.
  • Page 441 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 5. Refer to Figure 16-19. Remove cable (E4410-20164) (3) from bottom switch center port to Front End Assembly J9. 6. Remove cable (N9020-20144) (2) from top switch port 2 to center switch center port.
  • Page 442 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 8. Refer to Figure 16-20. Remove cable (N9020-20146) (1) between top switch port 4 and Low Band Switch Assembly connector that is closest to the inner chassis. Figure 16-20 W52 Cable Removal 9.
  • Page 443 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 10.Refer to Figure 16-22. Disconnect the ribbon cable to the Front End Controller J802. Remove the switch assembly (1) by removing the two screws (0515-1035) at the frame (2) and the single screw on the side (3) (0515-0372).
  • Page 444 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 12.Refer to Figure 16-24. Disconnect W7 from the Low Band Switch. Figure 16-24 W7 Removal N9030A PXA Signal Analyzer Service Guide...
  • Page 445 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 13.Refer to Figure 16-25. Disconnect the two wire harness connectors (1) located between the switches and the frame. Figure 16-25 Wire Harness Disconnect N9030A PXA Signal Analyzer Service Guide...
  • Page 446 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 14.Refer to Figure 16-26. Remove the top switch/bracket assembly (1)/(2) by removing the single screw on the side (4) (0515-0372). To separate the switch from the bracket, remove the two top screws (3) (0515-0372). Figure 16-26 Switch 2 Removal N9030A PXA Signal Analyzer Service Guide...
  • Page 447 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 15.Refer to Figure 16-27. Remove the bottom switch/bracket assembly (1)/(2) by removing the two screws on the top (3) (0515-1992). Figure 16-27 Switch 1 Removal Replacement 1. Refer to Figure 16-28.
  • Page 448 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Figure 16-28 Switch 1 Placement N9030A PXA Signal Analyzer Service Guide...
  • Page 449 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 2. Refer to Figure 16-29. Place the second switch/bracket assembly (1)/(2) on the bracket previously installed. Assure Keysight label on switch is facing up. To attach use the two screws (3) (0515-1992). Figure 16-29 Switch 2 Placement 3.
  • Page 450 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 5. Refer to Figure 16-30. Route W7 over bracket and switch as shown and insert W7 connector into Low Band Switch header. Ensure the locking tabs are engaged on both sides of the connector. Figure 16-30 W7 Routing N9030A PXA Signal Analyzer Service Guide...
  • Page 451 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 6. Refer to Figure 16-31. Reconnect the two wire harness connectors (1). Once connected, position the connections along side the switches. Figure 16-31 Wire Harness Routing N9030A PXA Signal Analyzer Service Guide...
  • Page 452 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 7. Refer to Figure 16-32. Attach the coaxial fixed attenuator (1) to switch port 1. Torque to 10 inch-lbs. Figure 16-32 Attenuator Installation N9030A PXA Signal Analyzer Service Guide...
  • Page 453 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 8. Refer to Figure 16-33. Install the bracket (1) to the switch (2) using three screws (3) (0515-1934). Assure the number 3 on the switch is positioned as shown. Torque screws to 6 inch-lbs. Install the ribbon cable (4) into the switch connector header.
  • Page 454 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 9. Refer to Figure 16-34. Install the switch assembly (1). Route the switch control cable between the switch and the chassis. The cable routes over the LO Synthesizer board ear then plugs into J802. If this is not routed correctly the cable can be damaged when the top brace is installed.
  • Page 455 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) Figure 16-35 Cable Routing Figure 16-36 Cable Routing N9030A PXA Signal Analyzer Service Guide...
  • Page 456 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 10.Refer to Figure 16-37. Install rigid cable (N9020-20146) (1) between top switch port 4 and Low Band Switch Assembly connector that is closest to the inner chassis. Torque to 10 inch-lbs. Figure 16-37 W52 Installation Item...
  • Page 457 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 11.Refer to Figure 16-38. Install rigid cable (N9020-20210) (1) between attenuator (connected to center switch port 1 and bottom switch port 1. Torque to 10 inch-lbs. Figure 16-38 W13, W15, W53 Installation Item Keysight Part Number N9020-20210...
  • Page 458 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 14.Refer to Figure 16-39. Install rigid cable (N9020-20145) (1) from top switch port 3 to Low Band Switch Assembly as shown. Torque to 10 inch-lbs. Figure 16-39 W10, W14, W54 Installation Item Keysight Part Number E4410-20163...
  • Page 459 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 17.Refer to Figure 16-40. Install rigid cable (N9020-20143) (1) from top switch port 1 to Attenuator B output as shown. Torque to 10 inch-lbs. Figure 16-40 W51 Installation Item Keysight Part Number N9020-20143 N9030A PXA Signal Analyzer Service Guide...
  • Page 460 Assembly Replacement Procedures RF Area (Options 503, 508, 513, 526) 18.Refer to Figure 16-41. Route all ribbon cables as shown to avoid being damaged when the top brace is installed. Figure 16-41 Ribbon Cable Routing 19.Refer to Figure 16-7. Position the RF bracket onto the chassis and replace the sixteen screws (0515-0372).
  • Page 461: Rf Area (Options 543, 544, 550)

    Assembly Replacement Procedures RF Area (Options 543, 544, 550) RF Area (Options 543, 544, 550) Refer to Figure 16-42. The RF area consists of RF attenuator A (1), RF attenuator B (2), low band switch assembly (3), YTF Preselector (4), and YTO (5).
  • Page 462 Assembly Replacement Procedures RF Area (Options 543, 544, 550) 3. Refer to Figure 16-43. Remove the RF bracket (1) by removing the sixteen screws (2) (0515-0372) using the T-10 driver. Figure 16-43 RF Bracket Removal N9030A PXA Signal Analyzer Service Guide...
  • Page 463: Attenuators

    Assembly Replacement Procedures RF Area (Options 543, 544, 550) Attenuators Removal 1. Refer to Figure 16-44. To remove Attenuator A (1) or Attenuator B (2), remove the semi-rigid cables W2, W3, W4, or W6 attached to the attenuator using the 5/16 inch wrench. 2.
  • Page 464 Assembly Replacement Procedures RF Area (Options 543, 544, 550) Replacement 1. Refer to Figure 16-44. Position the attenuator and magnetic shield in the bracket so that the attenuator ribbon connector end is “up”. 2. Replace the two screws (0515-0372) that attach the attenuator to the bracket.
  • Page 465: Low Band Switch

    Assembly Replacement Procedures RF Area (Options 543, 544, 550) Low Band Switch Removal If the analyzer has hardware for Options MPB and LNP installed, perform the removal procedure for Options MPB and LNP on page 473 first. 1. Refer to Figure 16-45.
  • Page 466 Assembly Replacement Procedures RF Area (Options 543, 544, 550) Figure 16-46 Low Band Switch Bracket Removal Figure 16-47 Low Band Switch and Bracket Separation N9030A PXA Signal Analyzer Service Guide...
  • Page 467 Assembly Replacement Procedures RF Area (Options 543, 544, 550) Replacement 1. Refer to Figure 16-47. Place the switch onto the bracket and replace the five screws (3) (0515-0372). Torque to 9 inch-pounds. 2. Place the switch/bracket into place into the chassis and replace the two screws (0515-0372).
  • Page 468: Ytf Preselector

    Assembly Replacement Procedures RF Area (Options 543, 544, 550) YTF Preselector Removal 1. Refer to Figure 16-48. Remove cables W56 and W57 from the YTF Preselector (1). 2. Remove the wire harness W11. 3. Refer to Figure 16-49. From the bottom of the instrument, remove the four screws (1) (0515-0372).
  • Page 469 Assembly Replacement Procedures RF Area (Options 543, 544, 550) Figure 16-49 YTF Preselector Screws N9030A PXA Signal Analyzer Service Guide...
  • Page 470 Assembly Replacement Procedures RF Area (Options 543, 544, 550) Replacement 1. Inspect the chassis where the YTF Preselector mounts and remove the gap pad if present (see Figure 16-50, item (1)). The gap pad may remain attached to the faulty YTF Preselector. 2.
  • Page 471: Yto

    Assembly Replacement Procedures RF Area (Options 543, 544, 550) Removal 1. Refer to Figure 16-51. Remove cable W20 from the YTO (1). 2. Remove cable W4. 3. Remove the ribbon cable W23 by pulling forward on the locking latch. 4. Refer to Figure 16-52.
  • Page 472 Assembly Replacement Procedures RF Area (Options 543, 544, 550) Figure 16-52 YTO Screws Replacement 1. Refer to Figure 16-52. Place the YTO into the chassis. Replace the two screws (1) (0515-0372). Torque to 9 inch-pounds. Figure 16-51. Replace the cables W20. Torque to 10 inch-pounds. 3.
  • Page 473: Options Mpb And Lnp

    Assembly Replacement Procedures RF Area (Options 543, 544, 550) Options MPB and LNP Removal 1. Refer to Figure 16-53. Remove rigid cable W51 (N9020-20171) (1) from top switch port 1 to Attenuator B output. Figure 16-53 W51 Cable Removal N9030A PXA Signal Analyzer Service Guide...
  • Page 474 Assembly Replacement Procedures RF Area (Options 543, 544, 550) 2. Refer to Figure 16-54 Figure 16-55. Remove cable W62 (N9020-20130) (3) from bottom switch port 2 to Front End Assembly J9. 3. Remove cable W61 (N9020-20129) (2) from bottom switch port 3 to YTF Assembly.
  • Page 475 Assembly Replacement Procedures RF Area (Options 543, 544, 550) 5. Refer to Figure 16-56. Remove cable W20 (N9020-20152) (3) from YTO to Front End Assembly J4. 6. Remove cable W8 (N9020-20131) (2) from Low Band Switch J2 to Front End Assembly J2. 7.
  • Page 476 Assembly Replacement Procedures RF Area (Options 543, 544, 550) 8. Refer to Figure 16-57. Remove cable W54 (N9020-20127) (2) from top switch port 3 to Low Band Switch J3. 9. Remove cable W52 (N9020-20125) (1) from top switch port 4 to Low Band Switch J1.
  • Page 477 Assembly Replacement Procedures RF Area (Options 543, 544, 550) 10.Refer to Figure 16-58. Disconnect the wire harness connector (1) located between the switch and the frame. Remove the ribbon cable from the rear of the top switch. Figure 16-58 Wire Harness Disconnect N9030A PXA Signal Analyzer Service Guide...
  • Page 478 Assembly Replacement Procedures RF Area (Options 543, 544, 550) 11.Refer to Figure 16-59. Remove the switch assembly (1) by removing the two screws (0515-1035) at the frame (2). Figure 16-59 Switch Assembly Removal 12.Refer to Figure 16-60. To separate the switches (2) and (4) from the bracket (1) (N9020-00021), remove the three screws (3) (0515-1934) for each switch.
  • Page 479 Assembly Replacement Procedures RF Area (Options 543, 544, 550) Replacement 1. Refer to Figure 16-60. Attach switches (2)and (4) to bracket with three screws 0515-1934 for each switch. Note that the switch with the wire pigtail (4) mounts below the switch without the pigtail (2). Torque to 6 inch-lbs.
  • Page 480 Assembly Replacement Procedures RF Area (Options 543, 544, 550) 4. Reconnect the wire harness connector. Once connected, position the connections along side the switches as shown in Figure 16-58. Plug in the ribbon cable to the rear of the top switch. 5.
  • Page 481: Rf Front End Assembly

    Assembly Replacement Procedures RF Front End Assembly RF Front End Assembly Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the instrument top brace. Refer to the Top Brace and Power Supply Bracket removal procedure.
  • Page 482 Assembly Replacement Procedures RF Front End Assembly Figure 16-62 RF Front End Assembly Removal - Microwave Figure 16-63 RF Front End Assembly Removal - Millimeter Wave N9030A PXA Signal Analyzer Service Guide...
  • Page 483: Replacement

    Assembly Replacement Procedures RF Front End Assembly Replacement 1. Refer to Figure 16-64. Attach the W22 ribbon cable to the Front End Assembly first. Route behind the Front End Assembly and ensure the cable is engaged under the tabs, then place the RF Front End Assembly into the chassis.
  • Page 484: Front End Control Assembly

    Assembly Replacement Procedures Front End Control Assembly Front End Control Assembly Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the instrument top brace. Refer to the Top Brace and Power Supply Bracket removal procedure.
  • Page 485: Replacement

    Assembly Replacement Procedures Front End Control Assembly 4. Refer to Figure 16-66. Remove the cables W25, W26, W16, W27, and W30 (Opt EXM) from the Front End Control assembly (1). 5. Remove the ribbon cables W5, W22, W28, W7, and W55 and the wire harnesses W11 and W12 from the Front End Control assembly.
  • Page 486: Lo Synthesizer Assembly

    Assembly Replacement Procedures LO Synthesizer Assembly LO Synthesizer Assembly Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the instrument top brace. Refer to the Top Brace and Power Supply Bracket removal procedure. 3.
  • Page 487: Replacement

    Assembly Replacement Procedures LO Synthesizer Assembly 4. Refer to Figure 16-68. Remove the cables W21 and W31 from the LO Synthesizer assembly (2) using the 5/16 inch wrench. 5. Remove W23 and W32. 6. Remove the two screws (3) (0515-1035). Figure 16-68 LO Synthesizer Assembly Removal Item...
  • Page 488: Reference Assembly

    Assembly Replacement Procedures Reference Assembly Reference Assembly Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the top brace. Refer to the Top Brace and Power Supply Bracket removal procedure. 3. Refer to Figure 16-69.
  • Page 489 Assembly Replacement Procedures Reference Assembly 4. Refer to Figure 16-70. Remove cables W3, W18, and W31 from the reference assembly (1) using the 5/16-inch wrench. Figure 16-70 Reference Board Cables Item Keysight Part Number N9020-20023 N9020-20022 N9020-20021 5. Remove the two screws (2) (0515-0372) attaching the Reference board to the chassis.
  • Page 490: Replacement

    Assembly Replacement Procedures Reference Assembly 6. Refer to Figure 16-71. Remove the other screw (0515-0372) attaching the reference wire hold down 2 to the chassis. Remove wire hold down 2. Figure 16-71 Wire Hold Downs 7. Remove cables W32, W33, W35 (Opt BBA), W36, W37, W39, and W47 from the Reference assembly.
  • Page 491: Option B1X

    Assembly Replacement Procedures Option B1X Option B1X Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the top brace. Refer to the Top Brace and Power Supply Bracket removal procedure. 3. Refer to Figure 16-72.
  • Page 492: Replacement

    Assembly Replacement Procedures Option B1X 4. Refer to Figure 16-73. Remove cables W34, W40, W41, W45, and W46 from the Wideband Analog IF assembly (2). 5. Remove ribbon cables W44. Figure 16-73 Option B1X Cables 6. The Wideband Analog IF (2) and Wideband Digital IF (1) assemblies can now be removed by pulling up on the ejectors to remove from the chassis.
  • Page 493: Option Bba

    Assembly Replacement Procedures Option BBA Option BBA Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the top brace. Refer to the Top Brace and Power Supply Bracket removal procedure. 3. Refer to Figure 16-74.
  • Page 494: Midplane Board Assembly

    Assembly Replacement Procedures Midplane Board Assembly Midplane Board Assembly Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the top brace and power supply bracket. Refer to the Top Brace and Power Supply Bracketremoval procedure.
  • Page 495: Midplane Board Replacement

    Assembly Replacement Procedures Midplane Board Assembly 7. Refer to Figure 16-76. Remove the six screws (2) (0515-0375) attaching the midplane board assembly (1) to the midplane bracket. The midplane board assembly can now be pulled up from the chassis by use of the ejectors.
  • Page 496: Rear Panel

    Assembly Replacement Procedures Rear Panel Rear Panel Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Refer to Figure 16-77. Remove W37 (2) cable from the rear panel using the 9/16- inch nut driver. Remove W27 (3) cable using the 5/16- inch wrench.
  • Page 497: Power Supply Assembly

    Assembly Replacement Procedures Power Supply Assembly Power Supply Assembly Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the rear panel. Refer to the Rear Panel removal procedure. 3. Refer to Figure 16-78.
  • Page 498: Replacement

    Assembly Replacement Procedures Power Supply Assembly Replacement 1. Slide the power supply assembly into the slot at the rear of the instrument and push on the assembly to mate the connectors to the midplane assembly. 2. Refer to Figure 16-78. Replace the three screws (1) (0515-1227) through the power supply bracket and into the power supply.
  • Page 499: Cpu Assembly

    Assembly Replacement Procedures CPU Assembly CPU Assembly Removal 1. Refer to Figure 16-79. Remove the six screws (1) (0515-0372) attaching the CPU assembly to the chassis. 2. The CPU assembly can be removed from the chassis by pulling straight out the back.
  • Page 500: Replacement

    Assembly Replacement Procedures CPU Assembly Replacement 1. Slide the CPU assembly into the slot at the rear of the instrument and push on the assembly to mate the connectors to the midplane assembly. Secure the board with the ejectors. 2. Refer to Figure 16-79.
  • Page 501: Disk Drive

    Assembly Replacement Procedures Disk Drive Disk Drive Electrostatic discharge (ESD) can damage or destroy electronic components. All work on electronic assemblies should be performed at a static-safe workstation. Refer to the documentation that pertains to your instrument for information about static-safe workstations and ordering static-safe accessories.
  • Page 502 Assembly Replacement Procedures Disk Drive 3. Refer to Figure 16-80. Locate and remove the existing disk drive carrier assembly (2) from the instrument by loosening the rear panel screw (1). Figure 16-80 Removing the Disk Drive Carrier Assembly N9030A PXA Signal Analyzer Service Guide...
  • Page 503 Assembly Replacement Procedures Disk Drive 4. Refer to Figure 16-81. Remove the 4 machine screws (1) (0515-0372) from the disk drive carrier assembly that secure the drive (2). Figure 16-81 Disk Drive Screws N9030A PXA Signal Analyzer Service Guide...
  • Page 504 Assembly Replacement Procedures Disk Drive 5. Remove the disk drive (2) from the carrier assembly. 6. Place the new disk drive onto the carrier assembly and attach with the 4 machine screws (1) (0515-0372). Torque to 9 in-pounds. 7. Refer to Figure 16-80.
  • Page 505: Disk Drive Interconnect

    Assembly Replacement Procedures Disk Drive Disk Drive Interconnect Removal 1. Remove the A5 Disk Drive assembly for the instrument. Refer to the “Disk Drive” removal procedure. 2. Remove the A4 CPU assembly from the instrument. Refer to the “CPU Assembly” removal procedure.
  • Page 506 Assembly Replacement Procedures Disk Drive 4. Remove the 2 screws (4) (0515-0372) that attached the A4A1 Disk Drive Interconnect board (5) to the A4 CPU assembly. 5. Unplug and remove the A4A1 Disk Drive Interconnect board from the A4 CPU assembly by carefully sliding the board out towards the disk drive bay opening (6).
  • Page 507: Aif/Dif Assembly

    Assembly Replacement Procedures AIF/DIF Assembly AIF/DIF Assembly Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the rear panel. Refer to the Rear Panel removal procedure. 3. Refer to Figure 16-84. Remove cables W26, W39, W42, and W47 from the bottom of the DIF assembly.
  • Page 508 Assembly Replacement Procedures AIF/DIF Assembly Figure 16-85 AIF Cables N9030A PXA Signal Analyzer Service Guide...
  • Page 509: Separate Aif/Dif Assembly

    Assembly Replacement Procedures AIF/DIF Assembly Separate AIF/DIF Assembly 1. To separate the AIF (1) from the DIF (2), unplug ribbon cable W43 from the AIF assembly. 2. Refer to Figure 16-86. From underneath the assembly, remove the three screws (3) (0515-0372). Figure 16-86 AIF/DIF Separation 1.
  • Page 510: Replacement

    Assembly Replacement Procedures AIF/DIF Assembly Replacement 1. Slide the AIF/DIF assembly into the slot at the rear of the instrument and push on the assembly to mate the connectors to the motherboard assembly. 2. Refer to Figure 16-85. Replace cables W25, W36, and W42 to the AIF assembly.
  • Page 511: Motherboard Assembly

    Assembly Replacement Procedures Motherboard Assembly Motherboard Assembly Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the rear panel. Refer to the Rear Panel removal procedure. 3. Remove the top brace and power supply bracket. Refer to the Top Brace and Power Supply Bracket removal procedure.
  • Page 512 Assembly Replacement Procedures Motherboard Assembly Figure 16-87 Midplane Bracket Removal Figure 16-88 Bottom Screws N9030A PXA Signal Analyzer Service Guide...
  • Page 513 Assembly Replacement Procedures Motherboard Assembly 16.Refer to Figure 16-89. Remove the left side chassis (1) (same side as the fan) by removing the nine screws (2) (0515-0372) (six on the bottom). Figure 16-89 Chassis Side Removal N9030A PXA Signal Analyzer Service Guide...
  • Page 514: Replacement

    Assembly Replacement Procedures Motherboard Assembly 17.Refer to Figure 16-90. Remove the motherboard (1) by removing the four screws (2) (0515-0372). Slide the motherboard back off the standoffs and lift it up and out. Figure 16-90 Motherboard Assembly Removal Replacement 1. Refer to Figure 16-90.
  • Page 515 Assembly Replacement Procedures Motherboard Assembly 5. Replace the Midplane assembly. Refer to the Midplane Board Assembly replacement procedure. 6. Replace the Front End Control assembly. Refer to the Front End Control Assembly replacement procedure. 7. Replace the LO Synthesizer assembly. Refer to the LO Synthesizer Assembly replacement procedure.
  • Page 516: Fan Assembly

    Assembly Replacement Procedures Fan Assembly Fan Assembly Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the top brace. Refer to the Top Brace and Power Supply Bracket removal procedure. 3. Remove the Front Frame Assembly. Refer to the Front Frame Assembly removal procedure.
  • Page 517 Assembly Replacement Procedures Fan Assembly 5. Refer to Figure 16-92. Unplug the fan wires from the motherboard. The fan assembly can now be lifted from the chassis. Figure 16-92 Fan Wires N9030A PXA Signal Analyzer Service Guide...
  • Page 518 Assembly Replacement Procedures Fan Assembly Replacing a Fan 1. Refer to Figure 16-93. To replace a fan, it is necessary to remove the 4 plastic rivets (3) (0361-1272) that attach the fan (1) and guard (2) to the fan bracket. To do this use a small screwdriver to unscrew the rivet and remove it from the bracket.
  • Page 519: Replacement

    Assembly Replacement Procedures Fan Assembly Replacement 1. Plug the fan wires into the motherboard. 2. Refer to Figure 16-91. Place the fan assembly into position in the chassis. Replace the twelve screws (1) (0515-0372) to attach the fan assembly to the chassis.
  • Page 520: Input Connector Assembly

    Assembly Replacement Procedures Input Connector Assembly Input Connector Assembly Removal 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. Remove the Front Frame Assembly. Refer to the Front Frame Assembly removal procedure. 3. Refer to Figure 16-94.
  • Page 521: Replacement

    Assembly Replacement Procedures Input Connector Assembly Replacement 1. Refer to Figure 16-94. Place the Input Connector Assembly into position in the chassis. Replace the two screws (1) (0515-0372) to attach the Input Connector Assembly to the chassis. Torque to 9 inch-pounds. 2.
  • Page 522: Front Frame Assembly

    Assembly Replacement Procedures Front Frame Assembly Front Frame Assembly Removal Make sure any connectors on the front panel are removed. 1. Remove the instrument outer case. Refer to the Instrument Outer Case removal procedure. 2. If Option EXM, External Mixing, is installed disconnect semi-rigid cable connection (1) on LO/IF cable.
  • Page 523: Replacement

    Assembly Replacement Procedures Front Frame Assembly Figure 16-96 Front Panel Cable Replacement 1. Reattach the ribbon cable W1. Ensure the locking tabs are engaged. 2. Refer to Figure 16-95. Carefully position the Front Frame Assembly onto the chassis. Ensure no cables are crushed. Replace the eight screws (2) (0515-1035), four on each side of the chassis.
  • Page 524: Front Frame Assembly Components - Lcd

    Assembly Replacement Procedures Front Frame Assembly Front Frame Assembly Components - LCD Access to any of the Front Frame assemblies requires removal of the Front Frame Assembly from the chassis. Figure 16-97 Front Frame Parts - LCD Item Description A1A5 Front Panel Daughter Board A1MP14 Display Bracket A1MP10-13 Cable Clamp (Front Panel Cables) A1MP18 and A1MP19 Shield, Front Panel...
  • Page 525 Assembly Replacement Procedures Front Frame Assembly Figure 16-98 Front Frame Parts (shields off) - LCD Item Description A1MP14 Display Bracket A1A2MP2 Speaker Foam A1A2MP1 Speaker A1A2 Front Panel Interface Board A1A5 Front Panel Daughter Board A1W1 Flex Circuit, Display to Front Panel Interface Board A1MP10-13 Cable Clamp (Front Panel Cables) A1W2 Cable Assembly, Front Panel Interface Board to Inverter Board...
  • Page 526 Assembly Replacement Procedures Front Frame Assembly Figure 16-99 Front Frame Exploded View - LCD N9030A PXA Signal Analyzer Service Guide...
  • Page 527 Assembly Replacement Procedures Front Frame Assembly Item Description Front Frame Front Frame Side Trim Strip (plastic) Front Frame Side Trim Strip (vinyl) Main Keyboard Overlay A1MP9 RPG Knob A1MP3-6 or A1MP20-22 Frequency Label Overlay, Left Display Cover Plate A1MP7 LCD Glass Filter A1MP8 LCD Lens Gasket A1MP2 Display Keypad Front Frame Ground Spring...
  • Page 528 Assembly Replacement Procedures Front Frame Assembly Figure 16-100 Front Frame Assembly Shields - LCD Item Description Screw M3 X 0.5 (5 mm long) (0515-0372) Screw M3 X 0.5 (8 mm long) (0515-0372) N9030A PXA Signal Analyzer Service Guide...
  • Page 529 Assembly Replacement Procedures Front Frame Assembly Inverter Board Assembly Removal 1. Refer to Figure 16-100. Remove the eight screws (32) (0515-0372) and the inverter top shield. 2. Disconnect the wires (1) from the Inverter board (3). 3. Remove the two screws (2) (0515-0372) securing the Inverter board (3). The Inverter board and inverter bottom shield can now be removed.
  • Page 530 Assembly Replacement Procedures Front Frame Assembly Display Assembly - LCD Removal 1. Remove the Inverter board and shields. 2. Refer to Figure 16-100. Remove the front panel shield by removing the four screws (28) (0515-0372). 3. Disconnect the cable A1W2 (25) from the LCD Inverter board (13) and unclip the cable from the cable clamps.
  • Page 531 Assembly Replacement Procedures Front Frame Assembly Figure 16-103 LCD and Display Bracket Separation Replacement 1. Refer to Figure 16-102. Place the display bracket into position in the Front Frame Assembly. Reconnect the flex circuit A1W1 (2) to the front panel interface board (4).
  • Page 532 Assembly Replacement Procedures Front Frame Assembly Daughter Board, Interface Board and Keypad Removal 1. Refer to Figure 16-99. Remove the RPG knob (5) by carefully pulling it off. 2. Remove the display. Refer to the Display Assembly - LCD removal procedure.
  • Page 533: Front Frame Assembly Components - Led

    Assembly Replacement Procedures Front Frame Assembly Front Frame Assembly Components - LED Access to any of the Front Frame assemblies requires removal of the Front Frame Assembly from the chassis. Figure 16-104 Front Frame Parts - LED Item Description A1MP14 Display Bracket A1A5 Front Panel Daughter Board A1MP18 and A1MP19 Shield, Front Panel Screw...
  • Page 534 Assembly Replacement Procedures Front Frame Assembly Figure 16-105 Front Frame Parts (shields off) - LED Item Description A1A2 Front Panel Interface Board A1A2MP1 Speaker A1A2MP2 Speaker Foam A1W1 Flex Circuit, Display to Front Panel Interface Board A1W2 Cable Assembly, Front Panel Interface Board to Inverter Board N9030A PXA Signal Analyzer Service Guide...
  • Page 535 Assembly Replacement Procedures Front Frame Assembly Figure 16-106 Front Frame Exploded View - LED N9030A PXA Signal Analyzer Service Guide...
  • Page 536 Assembly Replacement Procedures Front Frame Assembly Item Description Front Frame Main Keyboard Overlay Overlay, Left Display Cover Plate Front Frame Side Trim Strip (plastic) Front Frame Ground Spring A1A2 Front Panel Interface Board A1A2MP1 Speaker A1A2MP2 Speaker Foam A1A3 Liquid Crystal Display (LED backlight), Vibration Mounts A1A5 Front Panel Daughter Board A1MP1 Main Keypad...
  • Page 537 Assembly Replacement Procedures Front Frame Assembly Figure 16-107 Front Frame Assembly Shields - LED Item Description A1MP18 and A1MP19 Shield, Front Panel Screw M3 X 0.5 (5 mm long) (0515-0372) N9030A PXA Signal Analyzer Service Guide...
  • Page 538 Assembly Replacement Procedures Front Frame Assembly Display Assembly - LED Removal 1. Refer to Figure 16-107. Remove the front panel shield by removing the four screws (28) (0515-0372). 2. Refer to Figure 16-108. Disconnect the flex circuit A1W1 (1) and A1W3 (2) from the front panel interface board (4).
  • Page 539 Assembly Replacement Procedures Front Frame Assembly Figure 16-109 LED and Display Bracket Separation Replacement 1. Refer to Figure 16-108. Place the display bracket into position in the Front Frame Assembly. Reconnect the flex circuit A1W1 (1) and A1W3 (2) to the front panel interface board (4).
  • Page 540 Assembly Replacement Procedures Front Frame Assembly Daughter Board, Interface Board and Keypad Removal 1. Refer to Figure 16-106. Remove the RPG knob (17) by carefully pulling it off. 2. Remove the display. Refer to the Display Assembly - LCD removal procedure.
  • Page 541: Post-Repair Procedures

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide Post-Repair Procedures What You Will Find in This Chapter This chapter provides information that will enable you to return an instrument to full operation following the replacement of any instrument assembly. This information includes a table that shows which adjustments and/or performance tests must be executed after replacing an assembly.
  • Page 542: Post-Repair Procedures

    Post-Repair Procedures Post-Repair Procedures Post-Repair Procedures Table 17-1 lists the adjustments and performance verification tests needed after an assembly replacement. After an assembly is replaced, find the assembly that has been replaced in the left-hand column, and then perform the recommended adjustment and/or performance verification test.
  • Page 543 Post-Repair Procedures Post-Repair Procedures Table 17-1 Post-Repair Testing Requirements Performance Verifications to Perform After Ad justments to Perform Assembly (in the order listed) Ad justments A1A2 None Residual Responses Front Panel Displayed Average Noise Level Interface A1A3 None Residual Responses Liquid Crystal Displayed Average Noise Level Display...
  • Page 544 Post-Repair Procedures Post-Repair Procedures Table 17-1 Post-Repair Testing Requirements (Continued) Performance Verifications to Perform After Ad justments to Perform Assembly (in the order listed) Ad justments A9 & A10 Hardware Statistical Reset Utility Residual Responses RF Attenuators 50 MHz Calibrator Adjustment Displayed Average Noise Level Frequency Response (All Adjustments) Spurious Responses...
  • Page 545 Post-Repair Procedures Post-Repair Procedures Table 17-1 Post-Repair Testing Requirements (Continued) Performance Verifications to Perform After Ad justments to Perform Assembly (in the order listed) Ad justments Residual Responses FPGA Synchronization Front End Control Displayed Average Noise Level Front End Controller Attenuator Adjustment Assembly Absolute Amplitude Accuracy Frequency Response (All Tests)
  • Page 546 Post-Repair Procedures Post-Repair Procedures Table 17-1 Post-Repair Testing Requirements (Continued) Performance Verifications to Perform After Ad justments to Perform Assembly (in the order listed) Ad justments Frequency Response (all tests) Frequency Response (all tests) Preselector bypass Reset Low Noise Path switch using software switch (Option utility.
  • Page 547: Additional Tasks

    Post-Repair Procedures Post-Repair Procedures Additional Tasks Calibration Data Backup and Restore In order for the instrument being repaired to not need all of the instrument adjustments and performance verification tests to be run after the A5 Disk Drive is replaced the calibration data will need to be backed up onto an external drive prior to removing the existing disk drive.
  • Page 548 Post-Repair Procedures Post-Repair Procedures Figure 17-1 Alignment Data Wizard 5. Follow the on-screen instruction to backup the calibration data to the USB FLASH drive. If the Instrument Software Application Will Not Run 1. Connect a USB mouse to one of the instrument front panel USB ports. 2.
  • Page 549 Post-Repair Procedures Post-Repair Procedures Figure 17-2 Calibration Data Backup 5. Under the “Specify Backup Folder or File Name” use the mouse to select the “...” button to open the “Browse For Folder” dialog box. 6. Select the USB FLASH drive and press OK . While you can use the “Make New Folder”...
  • Page 550 Post-Repair Procedures Post-Repair Procedures Data Restore 1. Connect a USB mouse to one of the instrument front panel USB ports. 2. Locate the USB FLASH drive that was earlier used to backup the instrument calibration file and insert it into one of the instrument front panel USB ports.
  • Page 551 (serial numbers < MY/SG/US 52200000) 1. Connect an external USB keyboard to one of the front panel USB ports. 2. Turn on instrument power. 3. Confirm Keysight Technologies splash screen comes up within a few seconds as shown in Figure 17-3.
  • Page 552 Post-Repair Procedures Post-Repair Procedures 4. Press “F2” on the external keyboard when at the Keysight Technologies splash screen to enter the CPU BIOS Setup Utility as shown in Figure 17-4. Figure 17-4 CPU BIOS Setup Utility N9030A PXA Signal Analyzer Service Guide...
  • Page 553 Post-Repair Procedures Post-Repair Procedures 5. Press the Right Arrow on the external keyboard three times to highlight the Boot tab as shown in Figure 17-5. Figure 17-5 Boot Tab Highlighted 6. With Boot Order highlighted as shown in Figure 17-5 press Enter on the external keyboard to enter the Boot Order Configuration screen.
  • Page 554 Post-Repair Procedures Post-Repair Procedures Figure 17-6 Boot Tab Highlighted 7. If IDE HDD is not listed first in the boot priority, press the Down Arrow on the external keyboard to highlight IDE HDD as shown in Figure 17-6. N9030A PXA Signal Analyzer Service Guide...
  • Page 555 Post-Repair Procedures Post-Repair Procedures 8. Press the “+” key on the external keyboard to bring IDE HDD to the top of the list as shown in Figure 17-7. Figure 17-7 IDE HDD at Top of List Save Changes 1. Press “F10” on the keyboard to save changes. 2.
  • Page 556 Post-Repair Procedures Post-Repair Procedures Figure 17-8 Confirm BIOS Configuration N9030A PXA Signal Analyzer Service Guide...
  • Page 557 Post-Repair Procedures Post-Repair Procedures End User License Agreement (EULA) Acceptance The Microsoft End-User License agreement will be displayed whenever the A5 Disk Drive has been replaced, and this must be accepted. The License Agreement screen asks you to accept the terms of the End-User License Agreement for Windows XP.
  • Page 558 Post-Repair Procedures Post-Repair Procedures 1. Press Enter to proceed with the Windows XP setup. 2. When you see the Windows XP Setup Wizard screen as seen in Figure 17-10, press Enter to move to the License Agreement screen. Figure 17-10 Windows XP Setup Wizard 3.
  • Page 559 Post-Repair Procedures Post-Repair Procedures FPGA Synchronization There is FPGA (Field-Programmable Gate Array) program code on many different assemblies inside of the instrument, and all of these must be of a compatible version with the instrument software revision. In order to ensure that this requirement is met when either an assembly is replaced that contains FPGA code on it, or if the A5 Disk Drive is replaced with a drive that has a different version of software than the previous drive, you will need to take...
  • Page 560 Post-Repair Procedures Post-Repair Procedures Figure 17-11 FPGA Programming Utility 8. To program the FPGA code enter 1 and press Enter. You will need to confirm this selection by pressing 1 and Enter one more time. 9. The programming of the FPGA code could take a few minutes to complete. Once it has finished the instrument will reboot itself to use the new code and this process will then be completed.
  • Page 561 Post-Repair Procedures Post-Repair Procedures Programming Model and Serial Numbers Since the instrument model and serial numbers are stored only on the A7 Midplane board assembly, this information will be lost when this board assembly is replaced. Until the instrument model and serial numbers are restored the instrument application software will not allow any user measurements to be made, due to the fact that all previously installed license keys will not be accepted.
  • Page 562 Post-Repair Procedures Post-Repair Procedures N9030A PXA Signal Analyzer Service Guide...
  • Page 563: 18 Functional Tests

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide 18 Functional Tests Functional Test Versus Performance Verification Functional tests are tests of various instrument parameters that give a high degree of confidence that the analyzer is operating correctly. They are recommended as a check of analyzer operation for incoming inspection or after a repair.
  • Page 564: Before Performing A Functional Test

    Functional Tests Before Performing a Functional Test Before Performing a Functional Test 1. Ensure that you have the proper test equipment. 2. Switch on the unit under test (UUT) and let it warm up (in accordance with warm-up requirements in the instrument specifications). 3.
  • Page 565: Test Equipment

    Functional Tests Test Equipment Test Equipment The table below summarizes the test equipment needed to perform all of the functional tests. Alternate equipment model numbers are given in case the recommended equipment is not available. If neither the recommended nor the alternative test equipment are available, substitute equipment that meets or exceeds the critical specifications listed.
  • Page 566 Functional Tests Test Equipment Table 18-1 Analyzer Al ternate Recommended Option Item Critical Specifications Keysight Keysight Model Model Cables 3.5 mm (1 meter) Frequency: 10 MHz to 26.5 GHz 11500E 8120-4921 VSWR: < 1.4:1 Loss: < 2.0 dB 543, 544, 2.4 mm (1 meter) Frequency: 10 MHz to 50 GHz 8120-6164...
  • Page 567 Functional Tests Test Equipment Table 18-1 Analyzer Al ternate Recommended Option Item Critical Specifications Keysight Keysight Model Model Preamp Low Power Sensor 8487D 8485D c Frequency Range: 50 MHz to 50 GHz other than Amplitude Range: –70 to –20 dBm Miscellaneous Equipment Filter, 50 MHz Low Pass Cutoff Frequency: 50 MHz...
  • Page 568: Displayed Average Noise Level (Danl)

    Functional Tests Displayed Average Noise Level (DANL) Displayed Average Noise Level (DANL) Test Limits (with 0 dB input attenuation) Table 18-2 on page 569 for values. The Displayed Average Noise Level (DANL) of the signal analyzer is measured across a 10 kHz frequency span at several center frequencies. The analyzer input is terminated into a 50W load.
  • Page 569 Functional Tests Displayed Average Noise Level (DANL) 6. Rotate the knob and set the display line at the average amplitude of the displayed noise floor by visual inspection. 7. Confirm that the measurement is performed on the analyzer noise floor and not on a residual response within the displayed 10 kHz span.
  • Page 570: Frequency Readout Accuracy

    Functional Tests Frequency Readout Accuracy Frequency Readout Accuracy Test Limits Frequency Readout Accuracy is equivalent to the following equation: 0.25% span 5% RBW 2 Hz horizontal resolution ± × × × Table 18-3 on page 571 for actual values. The frequency readout accuracy is measured in several spans and center frequencies that allow both internal analyzer synthesizer modes and prefilter bandwidths to be tested.
  • Page 571: Procedure

    Functional Tests Frequency Readout Accuracy Procedure 1. Configure the equipment as shown in Figure 18-2. Confirm the analyzer’s built-in auto alignment has been performed within the past 24 hours. 2. On the synthesized sweeper, press PRESET, then set the controls as follows: FREQUENCY, 1505, MHz POWER LEVEL, –10, dBm...
  • Page 572: Second Harmonic Distortion (Shd)

    Functional Tests Second Harmonic Distortion (SHD) Second Harmonic Distortion (SHD) Test Limits Applied Frequency Distortion Mixer Level 40 MHz –15 dBm < –60 dBc a. Mixer Level = Input Level - RF Attenuation This test checks the second harmonic distortion of the signal analyzer by tuning to twice the input frequency and examining the level of the distortion product.
  • Page 573: Procedure

    Functional Tests Second Harmonic Distortion (SHD) Figure 18-3 Second Harmonic Distortion Test Setup Procedure 1. Configure the equipment as shown in Figure 18-3. 2. Press Mode, Spectrum Analyzer, Mode Preset on the signal analyzer and Preset the synthesized sweeper. 3. Set up the synthesized sweeper by pressing: Frequency, 40, MHz Amplitude, –5, dBm 4.
  • Page 574 Functional Tests Second Harmonic Distortion (SHD) 9. Press Peak Search. Enter the displayed value under the Measured Second Harmonic Distortion (dBc) heading in Table 18-4. Table 18-4 Second Harmonic Distortion Results Applied Frequency Measured Second Harmonic Distortion Mixer Level Specification (MHz) (dBc) (dBm)
  • Page 575: Amplitude Accuracy At 50 Mhz

    Functional Tests Amplitude Accuracy at 50 MHz Amplitude Accuracy at 50 MHz Test Limits Amplitude Accuracy should remain within 1.13 dB of the measured source value across the range of source levels and changes in resolution bandwidth. The preamp (Option P03, P08, P13, P26) should remain within ±1.3 dB of measured values.
  • Page 576: Procedure

    Functional Tests Amplitude Accuracy at 50 MHz Figure 18-4 Amplitude Accuracy Test Setup Procedure 1. Zero and calibrate the power meter. 2. Configure equipment as shown in Figure 18-4, with the power splitter connected directly to the signal analyzer input through the adapter. To minimize stress on the test equipment connections, support the power sensor.
  • Page 577 Functional Tests Amplitude Accuracy at 50 MHz Sweep/Control, Sweep Setup, Swp Time Rules, SA - Accuracy Meas Setup, Average/Hold Number, 20, Enter Trace/Detector, Trace Average Single 7. Perform the following steps for each row listed in Table 18-5: a. Set the synthesized sweeper amplitude to the value listed in the Nominal Source Amplitude column in Table 18-5.
  • Page 578: Testing Preamp Option (P03, P08, P13, P26)

    Functional Tests Amplitude Accuracy at 50 MHz Testing Preamp Option (P03, P08, P13, P26) Instruments containing Option P03, P08, P13, P26 must have the preamp function turned on and tested. Procedure 1. On the analyzer, press AMPTD Y Scale, More, Internal Preamp, Low Band. 2.
  • Page 579: Frequency Response (Flatness)

    Functional Tests Frequency Response (Flatness) Frequency Response (Flatness) Test Limits Frequency Range Limit Relative to 50 MHz 20 Hz to 3.6 GHz ±1.5 dB > 3.6 GHz to 8.4 GHz ±2.5 dB > 8.4 GHz to 13.6 GHz ±3.0 dB >...
  • Page 580: Procedure

    Functional Tests Frequency Response (Flatness) Critical Specifications Recommended Item (for this test) Keysight Model Power Splitter Frequency Range: 50 MHz to 26.5 GHz 11667B (Opt 503, 508, 513, 526) Tracking between ports: < 0.25 dB Power Splitter Frequency Range: 50 MHz to 50 GHz 11667C (Opt 543, 544, 550) Tracking between ports: <...
  • Page 581 Functional Tests Frequency Response (Flatness) 4. Press Mode, Spectrum Analyzer, Mode Preset on the signal analyzer, and press Preset on the synthesized sweeper. 5. Set up the synthesized sweeper by pressing: CW, 50, MHz Power level, –4, dBm 6. Set up the signal analyzer by pressing: Input/Output, More, Freq Ref In, External FREQ Channel, Center Freq, 50, MHz SPAN X Scale, Span, 50, kHz...
  • Page 582 Functional Tests Frequency Response (Flatness) Table 18-7 Frequency Response (Flatness) Results Analyzer Power Meter Meas Error Flatness Flatness Error Amplitude Measurement Normalized Test Limits Center to 50 MHz (dB) Frequency Meas Power Meas Flat meter error Norm 50 MHz 1 GHz ±1.5 dB 2 GHz 1.5 dB...
  • Page 583: Frequency Response (Flatness), Preamp On

    Functional Tests Frequency Response (Flatness), Preamp On Frequency Response (Flatness), Preamp On Test Limits Frequency Range Limit Relative to 50 MHz 100 kHz to 3.6 GHz ±2.0 dB > 3.6 GHz to 8.4 GHz ±3.0 dB > 8.4 GHz to 13.6 GHz ±3.5 dB >...
  • Page 584 Functional Tests Frequency Response (Flatness), Preamp On Critical Specifications Recommended Item (for this test) Keysight Model Power Sensor Frequency Range: 50 MHz to 26.5 GHz 8485D (Opt P03, P08, P13, P13) Amplitude Range: –65 dBm to –55 dBm Power Sensor Frequency Range: 50 MHz to 50 GHz 8487D (Opt P43, P44, P50)
  • Page 585: Procedure

    Functional Tests Frequency Response (Flatness), Preamp On Procedure 1. Zero and calibrate the power meter and power sensor as described in the power meter operation manual. 2. Configure the equipment as shown in Figure 18-5. Connect the power splitter to the signal analyzer input using the appropriate adapter.
  • Page 586 Functional Tests Frequency Response (Flatness), Preamp On 15.Repeat step 7 through step 14 and complete the remainder of Table 18-7 for the frequency range of your preamp. 16.Compute the measurement error (Meas = Meas - Power Error Meter 17.Compute the flatness error normalized to 50 MHz: (Meas - Meas @ 50 MHz)
  • Page 587 Functional Tests Frequency Response (Flatness), Preamp On Table 18-8 Frequency Response (Flatness) Results Analyzer Power Meter Meas Error Flatness Flatness Error Amplitude Measurement Normalized Test Limits Center to 50 MHz (dB) Frequency Meas Power Meas Flat meter error Norm 42.5 GHz ±5.0 dB 43.5 GHz ±5.0 dB...
  • Page 588: Scale Fidelity

    Functional Tests Scale Fidelity Scale Fidelity Test Limits The scale fidelity error will be £ ±1.0 dB with £ -10 dBm at the mixer. This test checks the scale fidelity of the instrument by maintaining a constant reference level and measuring signals of different amplitudes over most of the display range.
  • Page 589: Procedure

    Functional Tests Scale Fidelity Figure 18-7 Scale Fidelity Setup Averaging is used for all measurements to improve repeatability and reduce measurement uncertainty. Procedure 1. Configure the equipment as shown in Figure 18-7. 2. Preset the Source and press Mode, Spectrum Analyzer, Mode Preset on the analyzer.
  • Page 590 Functional Tests Scale Fidelity 8. On the analyzer, activate the Marker Delta function by pressing Peak Search, Marker Delta. 9. Perform the following steps for each attenuator setting listed in the table below: a. Select the next External attenuator setting. b.
  • Page 591 Functional Tests Scale Fidelity Table 18-9 Scale Fidelity Results Minimum Marker Del ta Value Maximum External Attenuator Setting (dB) (dB) (dB) Reference –11.0 –9.0 –21.0 –19.0 –31.0 –29.0 –41.0 –39.0 –51.0 –49.0 N9030A PXA Signal Analyzer Service Guide...
  • Page 592: Bbiq Input Frequency Response (Option Bba Only)

    Functional Tests BBIQ Input Frequency Response (Option BBA only) BBIQ Input Frequency Response (Option BBA only) Test Limits Frequency Range Limit Relative to 250 kHz Frequency Range Limit Relative to 250 kHz 250 kHz to 10 MHz (Standard) ± 1.75 dB 250 kHz to 25 MHz (Option B25) ±...
  • Page 593 Functional Tests BBIQ Input Frequency Response (Option BBA only) Figure 18-8 BBIQ Input Frequency Response Setup (I Input) Figure 18-9 BBIQ Input Frequency Response Setup (I Input) Figure 18-10 BBIQ Input Frequency Response Setup (Q Input) Figure 18-11 BBIQ Input Frequency Response Setup (Q Input) N9030A PXA Signal Analyzer Service Guide...
  • Page 594: Procedure

    Functional Tests BBIQ Input Frequency Response (Option BBA only) Procedure 1. On the X-Series analyzer, press Mode, IQ Analyzer (Basic). Press Mode Preset. 2. Press Input/Output, I/Q (to change to I/Q inputs), I/Q (to bring up the I/Q input menu), I/Q Cable Calibrate. Follow the instructions on screen. Use the short BNC cable listed above to perform the calibration.
  • Page 595 Functional Tests BBIQ Input Frequency Response (Option BBA only) 14.Press Peak Search on the X-Series analyzer. Record the marker amplitude reading in Table 18-10 for the I Input at 250 kHz. 15.Set the RF Signal Generator to each of the remaining frequencies listed in Table 18-10, up to the maximum IQ bandwid th of the X-Series analyzer.
  • Page 596 Functional Tests BBIQ Input Frequency Response (Option BBA only) 16.Set the RF Signal Generator frequency to 250 kHz 17.Connect the BNC Cable between the RF Signal Generator RF Output and the I input on the X-Series analyzer, see Figure 18-9 18.Connect the 50 Ohm termination to the I input on the X-Series analyzer, Figure 18-9 19.Press Peak Search on the X-Series analyzer.
  • Page 597 Functional Tests BBIQ Input Frequency Response (Option BBA only) Table 18-11 BBIQ Input Frequency Response, Q and Q Inputs RF Signal Q Input Q Input Test Limits Generator Frequency Marker Frequency Marker Frequency Amplitude Response Amplitude Response 12.5 MHz ±1.75 dB 15 MHz ±1.75 dB 17.5 MHz...
  • Page 598 Functional Tests BBIQ Input Frequency Response (Option BBA only) N9030A PXA Signal Analyzer Service Guide...
  • Page 599: 19 Instrument Software

    Keysight Technologies N9030A PXA Signal Analyzer Service Guide 19 Instrument Software What You Will Find in This Chapter Instrument Software Overview on page 600 Software Licensing on page 600 Software Updates on page 601 Instrument Measurement Application Software on page 601...
  • Page 600: Instrument Software Overview

    Instrument Software Instrument Software Overview Instrument Software Overview The instrument software, installed in every instrument, contains not only the spectrum analyzer measurement application, but also all of the other currently available measurement applications. However, only the licensed applications will be seen and available for use. To view the currently licensed measurement applications press System, Show, System.
  • Page 601: Software Updates

    Instrument Software Software Updates Software Updates Instrument Measurement Application Software Updates are installed much like most other types of commercial software packages. The latest revision of the software, along with complete installation instructions, can be obtained by one of two methods, which are: Web Download: The latest revision of the software can be downloaded from: www.keysight.com/find/xseries_software...
  • Page 602 Instrument Software Software Updates N9030A PXA Signal Analyzer Service Guide...
  • Page 603 Index RF front end part number replacement see A13 RF front end removal A5 disk drive assembly troubleshooting description A1A2 front panel interface troubleshooting board A5 hard disk drive Numerics description part number part number recovery process 50 ohm load removal removal 50 ohm/75 ohm minimum loss...
  • Page 604 Index after repairs CPU assembly external hard ware see post-repair see A4 CPU assembly procedures Align menu description alignment failure Alignments key external VGA monitor DANL test amplifiers daughter board amplitude accuracy test see A1A5 front panel option 1DS daughter board amplitude linearity test DC probes fans...
  • Page 605 CD-ROM errors green LED keypad warnings part number messages, warning removal Microwave Preselector Bypass Keysight Technologies (Option MPB) contacting handle troubleshooting Sales and Service offices see bail handle midplane splash screen hard disk drive see A7 midplane see A5 hard disk drive...
  • Page 606 Index preload measurement separate analog IF assembly updating measurement applications and digital IF assembly applications preselector serial number upgrades see A12 YTF service probes equipment USB keyboard and mouse AC and DC returning your instrument USB storage device tools User’s/Programmers Reference service menus Guides on CD-ROM service strategy...
  • Page 607 This information is subject to change without notice. © Keysight Technologies 2012-2017 Edition 1, May 2017 N9030-90030 www.keysight.com...

Table of Contents