Siemens SC 7000 Service Manual page 17

Chapter 1: General Information
1 Introduction
2 Overview
2.1 R50 Recorder
2.2 I Docking
NFINITY
Station
2.3 Docking Station
(Discontinued)
ASK-T898-03-7600
7k9kXLSM.c1.CD_ROM.fm/04-99/kaupp
This Manual is intended to serve as a source of technical information for
qualified personnel to use in servicing SC 7000 and SC 9000XL Monitors
and associated peripheral devices. In light of the state-of-the-art technology
used in the manufacture of Siemens' equipment, proprietary nature of the
software, and specialized equipment required for replacement of most
individual parts, Siemens policy (see
9000XL monitors, and peripheral modules specifically related to the SC
7000 or SC 9000XL, to be serviced only to the field-replaceable
subassembly level. Replacement of components other than those listed in
"Appendix A: Replacement
service depots.
SC 7000 and SC 9000XL patient monitors have been designed to function
as a portable or a stationary monitor with equal ease. Each has an internal
main battery, as well as provision for an additional external (auxiliary)
battery for extended operation as a portable monitor. For stationary
operation near a bedside, the monitor is placed on a specially designed
docking station attached to a shelf, wall, or IV pole that securely locks it into
place. While on the docking station, the monitor is powered by an external
power supply that also charges the monitor's main battery and external
battery (if installed). In addition, the docking station provides audio, video
and data signal connection to the local network as well as a variety of locally
installed peripheral devices such as a remote display/controller, recorder,
MIB converter, and Surgical Display Controller or SDC (sometimes referred
to as the Independent Surgeon Display or ISD). NBP is included as an
integral function. For airway and sidestream CO
cartridge can be installed on a slide mount on the back of the SC 7000.
Employing the "pick-and-go" concept, the monitor is simply picked up off of
the docking station to return it to portable operation, with no interruption in
patient monitoring.
An R50 Recorder connects to the SC 7000 and SC 9000XL via a CPS or
IDS. The recorder may be either a network or local recorder, depending on
configuration of a CPS. If plugged directly into an IDS, the recorder
functions as only a local recorder for any monitor mounted on the IDS. For
standalone portable operation, an interface plate can be used to provide
recorder connection. The R50 Recorder prints on 50mm wide paper, and
has three control keys -- Start Cont., Alternate Speed, and Stop.
The I Docking Station (IDS) is an active device. With its separate
NFINITY
power supply it replaces the discontinued Basic I
Docking Station combination (see Sections 2.3 and 2.4). As a docking
station, it serves as a secure mount for SC 7000 and SC 9000XL (and also
for SC 9000, SC 6000P and SC 6002) Monitors in "Pick-and-Go"
operations. When equipped with a MIB Option, an IDS provides the
combined functionality of a Device CPS and Breakout Box.
A docking station is a passive device that provides a sturdy mount for the
SC 7000 or SC 9000XL while supporting the "pick and go" concept. The
docking station mounts near a bedside, attached to a shelf, wall, or an IV
pole, and provides pass-through to a CPS for the signals from a SC 7000
or SC 9000XL. A second docking station supports peripheral devices such
as the R50 Recorder.
Siemens Medical Systems, EM-PCS Danvers
NOT A CONTROLLED DOCUMENT
Section 3) is for SC 7000 and SC
Parts", should be performed only at Siemens
monitoring, an etCO
2
NFINITY
2
N CPS and
ET
1