Table of Contents
Advertisement
TMS800E13 OPERATOR MANUAL
SECTION CONTENTS
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Installing Cable on the Hoist . . . . . . . . . . . . . . . . . 4-1
Cable Reeving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Dead-End Rigging/Wedge Sockets . . . . . . . . . . . . 4-3
Installing Wedge and Socket . . . . . . . . . . . . . . . . 4-3
Removable Counterweight . . . . . . . . . . . . . . . . . . 4-8
Mounting the Counterweight . . . . . . . . . . . . . . . . . 4-8
Stowing the Counterweight . . . . . . . . . . . . . . . . . . 4-8
Installing the Bi-Fold Manual Jib. . . . . . . . . . . . . 4-10
Checking the Transport Condition . . . . . . . . . . . 4-10
Jib Erecting and Stowing Procedure . . . . . . . . . 4-13
General Warnings . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Erecting Procedure . . . . . . . . . . . . . . . . . . . . . . . 4-13
Stowing Procedure . . . . . . . . . . . . . . . . . . . . . . . 4-19
section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Raising and Lowering the Hydraulic Jib . . . . . . . 4-22
Transportation on a Separate Vehicle . . . . . . . . 4-23
Lifting Limit Switch on the Lattice Extension. . . . 4-23
10.1 m (33 ft) Section . . . . . . . . . . . . . . . . . . . . . 4-24
Positioning/Removing the Hoist Cable . . . . . . . . 4-25
Removing the Bi-Fold Manual Jib . . . . . . . . . . . . 4-26
Installing/Removing 4.9 m (16 ft) Sections. . . . . 4-27
Installing the 4.9 m (16 ft) Sections. . . . . . . . . . . 4-27
Removing the 4.9 m (16 ft) Sections. . . . . . . . . . 4-27
Jib (Additional Equipment) . . . . . . . . . . . . . . . . . 4-27
GENERAL
This section provides procedures for installing the hoist
cable on the hoist drum, cable reeving, and erecting and
stowing the jib.
GROVE
SECTION 4
SET-UP AND INSTALLATION
Assembly Of Jibs . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
Auxiliary Single-Sheave Boom Nose (Additional
Equipment). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32
Nose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33
Rigged Lattice Extension . . . . . . . . . . . . . . . . . . . 4-36
Telescoping with Rigged Lattice Extension . . . . 4-36
Operating with the Lattice Extension . . . . . . . . . 4-36
Monthly Maintenance Work . . . . . . . . . . . . . . . . . 4-37
INSTALLING CABLE ON THE HOIST
If cable is wound from the storage drum, the reel should
be rotated in the same direction as the hoist.
NOTE:
Published 02-06-2014, Control # 495-00
SET-UP AND INSTALLATION
Identification and Slinging Points. . . . . . . . . . . . . 4-27
Electrical Connection at the Jib . . . . . . . . . . . . . . 4-29
the 4.9 m (16 ft) Section . . . . . . . . . . . . . . . . . . . 4-30
Positioning/Removing the Hoist Cable . . . . . . . . 4-31
Inserts Erected. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32
Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32
Nose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32
Nose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33
Rigging in Transport Position. . . . . . . . . . . . . . . . 4-33
Rigging in Working Position. . . . . . . . . . . . . . . . . 4-34
Attaching and Removing Hoist Cable . . . . . . . . . 4-35
Single-Sheave Boom Nose . . . . . . . . . . . . . . . . . 4-35
Lifting Limit Switch . . . . . . . . . . . . . . . . . . . . . . . . 4-35
Exceeded. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36
CAUTION
The cable should preferably be straightened before
installation on the hoist drum.
4
1
Advertisement
Table of Contents
Need help?
Do you have a question about the Grove TMS800E13 and is the answer not in the manual?