Emerson Rosemount Analytical X-STREAM X2 Series Instruction Manual page 369

Instruction Manual
HASX2E-IM-HS
10/2012
9.4 List of Parameters and Registers - Sorted by Registers
Address
Daniel Modicon
2033 2033 Control.ApplyGas.PumpState
2033 2033 Status.Calibration.PumpState
2037 2037 Control.ResetDevice
2038 2038 Control.AcknowledgeStates
2039 2039 Control.RemoteExclusive
3001 3001 Service.General.NumberChannels
3002 3002 Service.General.WarmupTime
Setup.Measurement.Response-
3003 3003
Time1
Setup.Measurement.Response-
3004 3004
Time2
Setup.Measurement.Response-
3005 3005
Time3
Setup.Measurement.Response-
3006 3006
Time4
3007 3007 Service.Linearizer.Unlinear
3008 3008 Service.RemoteSecurity
Service.Measurement.MaxConce-
3011 3011
Percent1
Service.Measurement.MaxConce-
3012 3012
Percent2
Service.Measurement.MaxConce-
3013 3013
Percent3
Service.Measurement.MaxConce-
3014 3014
Percent4
Service.Measurement.Difference-
3015 3015
Measurement
Setup.In/Outputs.AnalogOut.
3016 3016
AOutType
Setup.In/Outputs.AnalogOut.AOut-
3017 3017
SignalAssign1
Setup.In/Outputs.AnalogOut.AOut-
3018 3018
SignalAssign2
Setup.In/Outputs.AnalogOut.AOut-
3019 3019
SignalAssign3
Setup.In/Outputs.AnalogOut.AOut-
3020 3020
SignalAssign4
3021 3021 Setup.Calibration.ToleranceCheck
Emerson Process Management GmbH & Co. OHG
Data
Tag Name
Type
Boolean
Boolean
Boolean
Boolean
Boolean
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Word
Client
Access
R/W 0=Off, 1=On
RO state of built-in pump
R/W reset the device: 0=none, 1=reset
R/W 1=Acknowledge device's states, 0=no effect
Device access mode (0=Remote&LOI, 1=Remo-
R/W
teOnly)
R/W number of built-in component channels
R/W time in secs that is used for warmup phase
R/W signal damping (in secs) for gas change of comp1
R/W signal damping (in secs) for gas change of comp2
R/W signal damping (in secs) for gas change of comp3
R/W signal damping (in secs) for gas change of comp4
activates unlinear concentration measurement (0
R/W
= no, 1 = yes)
R/W Input Code to enable service accesss
max. allowed values in % of range for cal gases
R/W
and conc limits
max. allowed values in % of range for cal gases
R/W
and conc limits
max. allowed values in % of range for cal gases
R/W
and conc limits
max. allowed values in % of range for cal gases
R/W
and conc limits
bitfield to enable difference mode (b0=Ch1,
R/W
b1=Ch2 etc.)
AOut behavior (0=0_20,1=4_20,2=0_20L,3=4_20
R/W
L,4=0_20H,5=4_20H)
asgn AOut1(0=std,1=AdjStart,2=AdjEnd, 3=Rng-
R/W
C2)
asgn AOut2 (0=std,1=AdjStart,2=AdjEnd, 3=Rng-
R/W
C2)
asgn AOut3 (0=std,1=AdjStart,2=AdjEnd, 3=Rng-
R/W
C2)
asgn AOut4 (0=std,1=AdjStart,2=AdjEnd, 3=Rng-
R/W
C2)
check deviation tolerance (0=Off,1=On/
R/W
AutoClear,2=On)
X-STREAM X2
Description
9-23