Daikin VAM-FA8VE Technical Data Manual page 177

7 Product Specification
7 - 1 VKM-GAMV1
7 - 1 - 5 Wiring diagram
VKM50,80,100GAMV1
Power supply
220-240V
~
50 Hz
Control box
Indoor unit
A1P Printed circuit board
A2P Printed circuit board
A3P Printed circuit board (adapter for wiring)
C1, C2 Capacitor (M1F)
F1U Fuse ( , 10A, 250V) (A1P)
F1U Fuse ( , 5A, 250V) (A2P)
F1U, F2U Fuse ( , 5A, 250V) (A3P)
F1UT-F2UT Thermo switch
(152°C) (M1F, M2F built-in)
HAP Light emitting diode
(service monitor-green) (A1P)
HAP Light emitting diode
(service monitor-green) (A2P)
K1R~K3R Magnetic relay (M1F) (A1P)
K4R~K6R Magnetic relay (M2F) (A1P)
K7R Magnetic relay (M1D) (A1P)
K8R Magnetic relay (S1L)
KCR, KFR Magnetic relay (A3P)
: Terminal block
,
: Connector
: Short circuit connector
: Terminal
: Field wiring
NOTES
1 In case of using central remote control, connect it to the unit in accordance with the attached instruction manual.
2 In case using wiring adapter, connect it to the unit in accordance with the attached installation manual.
3 When connecting the input wires from outside, fresh up control operation can be selected by remot control, in details, refer to the installation manual
attached the unit.
4 When connecting the input wires from outside, forced off or on/off control operation can be selected by remot control, in details, refer to the In case
of installation manual attached the unit.
5 In case installing a humidistat S1H (locally procured), remove the short circuit wiring between (1) and (2) as shown in the figure right.
6 Do not remove the short circuit connectors of X8A and X9A. The unit will not run if they are removed.
7 SS1 (A3P) has already been set to off at factory set. Humidifying becomes impossible, if the setting are changed.
8 SS1 (A1P) has already been set to 'nor', at factory set. The unit will not run if the setting are changed.
9 Use copper conductors only.
• HRV • VKM-GAMV1
Adapter PC board for wiring
External output
(optional accessories)
terminals
Note 2
Contact
capacity
AC220-240V
0.01~1.6A
Note 8
KHR, KHuR Magnetic relay (A3P)
KSR Magnetic relay (Y1S)
M1D Motor (damper motor)
M1F Motor (supply air fan)
R1T Thermistor (indoor air)
R2T Thermistor (outdoor air)
R3T Thermistor (inlet air into coil)
R4T, R5Y Thermistor (liquid/gas pipe of coil)
S1L Float switch (humidifier)
S1Q Limit switch (damper motor)
SS1 Selector switch (for especially use) (A1P)
SS1 Selector switch (humidistat input) (A3P)
T1R Transformer (220-240V/22V)
T2R Transformer (220-240V/22V)
X1M Terminal block (power supply)
X1M, X2M Terminal block (control) (A3P)
X2M Terminal block (control) (A1P)
X3M Terminal block (control)
X17A, X19A Connector (relaying wire)
Colors:
• HRV • Heat Reclaim Ventilation
Note 7
Note 5
Note 6
Note 3
Input from
outside
X20A
Y1E
Y2S
SS1
Ry1
Ry2
Tes10
X11A
X18A
S1H
BLK: Black PNK:
BLU: Blue RED:
GRN: Green WHT: White
ORG: Orange YLW:
Note 5
Note 4
Input from outside
Note 1
Transmission wiring,
central remote control unit
Wired remote control
(optional accessory)
Connector (relaying wire)
Electronic expansion valve
Feed water solenoid valve
Optional accessories
Wired remote control
Select switch (main/sub)
Adaptor PC board for wiring (KRP50-2)
Magnetic relay (operation/stop)
Magnetic relay (for humidifier operation)
Terminal block (for external output)
Connector for optional parts
Connector (adapter power supply) (A1P)
Connector (wiring adapter for electrical
appendices) (A2P)
Local supplied parts
Humidistat
Pink
Red
Yellow
3D051310
2
7
175