Example Output Of; Install_Fs:partial Recovery (Setup) - Lucent Technologies AP-3 User Manual

Example Output of

install_fs:partial
recovery (setup)
101-1830-001 Issue 1.0
The example output below shows the procedure used to restore on an
A1000 partial recovery with setup, install_fs menu option 3.
____________________________________________________________________________
...boot from CDROM...
# tar xvf /dev/rmt/0
x ., 0 bytes, 0 tape blocks
x ./aps_enhance, 10381 bytes, 21 tape blocks
x ./cmdq_rem.sql, 2203 bytes, 5 tape blocks
x ./disk0.vtoc.4GB, 537 bytes, 2 tape blocks
x ./disk0.vtoc.9GB, 544 bytes, 2 tape blocks
x ./disk1.vtoc.4GB, 556 bytes, 2 tape blocks
x ./disk1.vtoc.9GB, 555 bytes, 2 tape blocks
x ./tape_config, 384 bytes, 1 tape blocks
x ./disk0.vtoc, 537 bytes, 2 tape blocks
x ./disk1.vtoc, 556 bytes, 2 tape blocks
x ./disk2.vtoc, 679 bytes, 2 tape blocks
x ./disk2.vtoc.4GB, 565 bytes, 2 tape blocks
x ./disk2.vtoc.4GB.a1, 679 bytes, 2 tape blocks
x ./disk2.vtoc.9GB.a1, 647 bytes, 2 tape blocks
x ./format_4GB.dat, 384 bytes, 1 tape blocks
x ./format_9GB.dat, 387 bytes, 1 tape blocks
x ./informix_lic, 2050 bytes, 5 tape blocks
x ./init_load, 9371 bytes, 19 tape blocks
x ./install_fs, 25631 bytes, 51 tape blocks
x ./restore_homes, 7243 bytes, 15 tape blocks
x ./sys_backup, 3701 bytes, 8 tape blocks
x ./system.a1, 2575 bytes, 6 tape blocks
x ./system.mp, 2406 bytes, 5 tape blocks
x ./x25_lic, 1453 bytes, 3 tape blocks
x ./CMDQ_REM, 2 bytes, 1 tape blocks
#
#
#
# ./install_fs
This tape was created Thu Feb 18 23:44:03 MST 1999 on system apstest1
This system (apstest1) has an A1000 Open Storage Array installed
The filesystem layout is as follows
Filesystem Kbytes
/dev/dsk/c0t0d0s0 2096263 /
/dev/dsk/c0t1d0s1 2641927 /var
/dev/dsk/c0t1d0s0 6050021 /export/home0
/dev/dsk/c1t5d0s0 2414815 /export/home1
/dev/dsk/c1t5d0s1 6091518 /export/home2
WARNING: The hardware configuration of this system must match the
configuration shown above.
an A1000 disk array cannot be installed on a system with
a MultiPack disk array, and vice versa.
WARNING: this is a destructive installation of software.
the filesystems you select to be installed/restored will be
DESTROYED. You should backup the system before proceeding.
Proceed with the installation?
#
# ./install_fs
This tape was created Thu Feb 18 23:44:03 MST 1999 on system apstest1
This system (apstest1) has an A1000 Open Storage Array installed
The filesystem layout is as follows
Filesystem Kbytes
/dev/dsk/c0t0d0s0 2096263 /
/dev/dsk/c0t1d0s1 2641927 /var
/dev/dsk/c0t1d0s0 6050021 /export/home0
/dev/dsk/c1t5d0s0 2414815 /export/home1
/dev/dsk/c1t5d0s1 6091518 /export/home2
WARNING: The hardware configuration of this system must match the
Backing Up and Restoring Data
Mounted On
A tape made on a system with
(yes/no) [no]: YES
Mounted On
All data in
223