Example Output Of; Install_Fs:full Recovery, (Setup) - Lucent Technologies AP-3 User Manual

APS (Application Plus Server) 4.1 Users Guide

Example Output of

install_fs:full
recovery, (setup)
218
install_fs menu option 1 performs a full restore and prompts for setup
information. This is the menu option used when installing a new drive or
a new site.
The example output below shows the procedure used to restore on an
A1000-Full recovery with setup, install_fs menu option 1. Another
example of this menu choice is in ''Installing the APS Tape'' on page 50.
____________________________________________________________________________
#
#
# tar xvf /dev/rmt/0
x ., 0 bytes, 0 tape blocks
x ./cmdq_rem.sql, 1820 bytes, 4 tape blocks
x ./disk0.vtoc.4GB, 537 bytes, 2 tape blocks
x ./disk0.vtoc.9GB, 544 bytes, 2 tape blocks
x ./disk1.vtoc.4GB, 556 bytes, 2 tape blocks
x ./disk1.vtoc.9GB, 555 bytes, 2 tape blocks
x ./init_load, 10597 bytes, 21 tape blocks
x ./tape_config, 384 bytes, 1 tape blocks
x ./disk0.vtoc, 537 bytes, 2 tape blocks
x ./disk1.vtoc, 556 bytes, 2 tape blocks
x ./disk2.vtoc, 679 bytes, 2 tape blocks
x ./disk2.vtoc.4GB, 565 bytes, 2 tape blocks
x ./disk2.vtoc.4GB.a1, 679 bytes, 2 tape blocks
x ./disk2.vtoc.9GB.a1, 647 bytes, 2 tape blocks
x ./format_4GB.dat, 384 bytes, 1 tape blocks
x ./format_9GB.dat, 387 bytes, 1 tape blocks
x ./informix_lic, 2032 bytes, 4 tape blocks
x ./install_fs, 25631 bytes, 51 tape blocks
x ./restore_homes, 7980 bytes, 16 tape blocks
x ./sys_backup, 3701 bytes, 8 tape blocks
x ./system.a1, 2577 bytes, 6 tape blocks
x ./system.mp, 2408 bytes, 5 tape blocks
x ./x25_lic, 1453 bytes, 3 tape blocks
x ./CMDQ_REM, 2 bytes, 1 tape blocks
#
#
# ./install_fs
This tape was created Fri Apr
This system (apstest1) has an A1000 Open Storage Array installed
The filesystem layout is as follows
Filesystem Kbytes
/dev/dsk/c0t0d0s0 4352742 /
/dev/dsk/c0t1d0s1 2641927 /var
/dev/dsk/c0t1d0s0 6050021 /export/home0
/dev/dsk/c1t5d0s0 2414815 /export/home1
/dev/dsk/c1t5d0s1 6091518 /export/home2
WARNING: The hardware configuration of this system must match the
configuration shown above.
an A1000 disk array cannot be installed on a system with
a MultiPack disk array, and vice versa.
WARNING: this is a destructive installation of software.
the filesystems you select to be installed/restored will be
DESTROYED. You should backup the system before proceeding.
Proceed with the installation?
1. Full system installation and setup
2. Full system recovery (no setup)
3. Partial system recovery and setup
4. Partial system recovery (no setup)
5. Help
6. Quit
9 09:36:46 MDT 1999 on system apstest1
Mounted On
A tape made on a system with
(yes/no) [no]: y
101-1830-001
All data in
Issue 1.0