Canon imageRUNNER ADVANCE C5051 Series Service Manual page 887

■ IMG-SPD
COPIER > OPTION > IMG-SPD
FX-D-TMP Set small paper down sequence start temp
Lv.1 Details To set temperature to start the down sequence control to small size
paper (width direction is smaller than A4R).
As the value is incremented by 1, the temperature is increased by 5
deg C from the initial setting temperature.
Use case When improving hot offset on the edge of paper and productivity
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -4 to 4
-4: -20 deg C, -3: -15 deg C, -2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1:
5 deg C, 2: 10 deg C, 3: 15 deg C, 4: 20 deg C
Unit deg C
Default value 0
FIX-ROT Set idle rotn stop temp after s-ppr feed
Lv.1 Details Temperature on the edges of the Fixing Film becomes higher than
the temperature at the center when feeding large size paper followed
by small size paper through the Fixing Assembly. Idle rotation is
executed until temperature is decreased to the specified value after
feeding small size paper to prevent occurrence of fixing offset or
wrinkles.
To set the temperature which is the condition to stop idle rotation.
As the value is incremented by 1, the temperature is increased by 5
deg C from the initial setting temperature.
Temperature is detected by the Sub Thermistor 1 and 2.
Use case When improving hot offset on the edge of paper and productivity
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: 5 deg C, 2: 10 deg C
Unit deg C
Default value 0
8
Service Mode > COPIER > OPTION > IMG-SPD
8 Service Mode > COPIER > OPTION > IMG-SPD
COPIER > OPTION > IMG-SPD
ARC-INT1 Set of ARCDAT interruption interval
Lv.2 Details To set the number of sheets as the intervals at which ARCDAT
control is executed.
When the number of sheets reaches the specified value, ARCDAT
control is executed by interrupting an ongoing job.
Decrease the value when the density varies dramatically, and
increase the value to reduce downtime due to the control.
If the value is too small, the productivity is lowered. If the value is too
large, the density of image becomes different before and after the
interruption.
Actual setting value is calculated by dividing the entry value by 0.9
and rounding up after the decimal points. (e.g.: If an entry value is
100, setting value will be 112.)
Use case - When the density varies dramatically
- When decreasing downtime
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 5 to 1000
Unit sheet
Default value 100
Related service mode COPIER> OPTION> IMG-LSR> ARC-INT2
ARC-INT2 Set ARCDAT exe interval: last rotation
Lv.2 Details To set the number of sheets which ARCDAT control is not executed,
from the start of a job.
ARCDAT control which is supposed to be executed during the
specified number of sheets is executed at last rotation of the previous
job. Since the number of interruptions during a job is reduced, the
productivity is enhanced.
However, the number of times of ARCDAT control executed at last
rotation might be increased depending on the print conditions.
Actual setting value is calculated by dividing the entry value by 0.9
and rounding up after the decimal points. (e.g.: If an entry value is
25, setting value will be 28.)
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Do not set a larger value than ARC-INT1.
Display/adj/set range 5 to 1000
Unit sheet
Default value 25
Related service mode COPIER> OPTION> IMG-LSR> ARC-INT1
8-187
8-187