Canon imageRUNNER ADVANCE C5051 Series Service Manual page 911

COPIER > OPTION > USER
TAB-ACC ON/OFF of auto cst change for tab ppr
Lv.1 Details To set to enable/disable auto cassette change when tab paper runs
out.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to instruct the user to thoroughly comply the following:
- Use tab paper with the same number of tabs.
- Set tab paper.
Be sure to comply the above; otherwise, proper print is not available
and it can cause soiling inside the machine because of toner.
Display/adj/set range 0 to 1
0: Auto cassette change disabled, 1: Auto cassette change enabled
Default value 0
BCNT-AST Set of inbox print charge target job
Lv.1 Details To set the job type that advances the count in inbox print with NE
Controller (ASSIST).
Use case When switching the job type that is subject to counting of the inbox
print with NE Controller
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: PDL job, 1: Copy job
Default value 0
PRJOB-CP Set count TX at RX/report print
Lv.2 Details To set to enable/disable a page-basis count pulse transmission to the
charge management device at the time of reception print or report
print.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: No transmission, 1: Transmission
Default value 0
DFLT-CPY Setting of color mode for copy
Lv.1 Details To set the default color mode for copy operation.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Based on Auto/ACS/Printer Driver settings, 1: Color mode, 2:
Black mode
Default value EUR: 2, Other: 0
8
Service Mode > COPIER > OPTION > USER
8 Service Mode > COPIER > OPTION > USER
COPIER > OPTION > USER
DFLT-BOX Set of color mode for inbox print
Lv.1 Details To set the default color mode for inbox print operation.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Based on Auto/ACS/Printer Driver settings, 1: Color mode, 2:
Black mode
Default value EUR: 2, Other: 0
DOC-REM Display/hide of original removal message
Lv.1 Details To set whether to display or hide the message to remove original
when scanning with DADF without opening/closing DADF after
scanning with the Copyboard.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
DPT-ID-7 Password entry set at dept ID reg/auth
Lv.2 Details To set whether to enter a password at the time of registration/
authentication of department ID.
With the setting to require entry, entry of 7-digit password is required
beside department ID.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Department ID only, 1: 7-digit (password) entry
Default value 0
RUI-RJT Connct set at invalid auth from remoteUI
Lv.2 Details To set whether to disconnect HTTP port when the machine receives
invalid authentication from remote UI 3 times.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Continued connection, 1: Disconnected
Default value 0
8-211
8-211