Canon imageRUNNER ADVANCE C5051 Series Service Manual page 885

■ FEED-SW
COPIER > OPTION > FEED-SW
EVLP-SPD Envelope feeding speed setting
Lv.1 Details To set the envelope feeding speed.
By feeding an envelope at 1/2 speed (default) in the case of a high
humidity environment, the glue flap may adhere at the time of fixing.
As a result of that, the envelope may not be opened.
By setting to 1/1 speed, adhesion can be prevented, but fixing might
be deteriorated in a low humidity environment.
Use case When a glue flap of envelope adheres
Adj/set/operate method Enter the setting value, and then press OK key.
Caution The fixing is deteriorated by setting 1/1 speed in a low humidity
environment.
Display/adj/set range 0 to 1
0: 1/2 speed, 1: 1/1 speed
Default value 0
EVLP-FS Setting of fixing speed with envelop
Lv.2 Details To set fixing speed when feeding envelope.
As the value is incremented by 1, the fixing speed changes by 0.1%.
Decrease the value when fine line displacement occurs on trailing
edge of envelop, and increase the value when wrinkles occur.
Use case When fine line displacement or wrinkles occur on trailing edge while
feeding envelop
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Caution Be sure to change the value little at a time because when setting an
extreme value, phenomenon opposite to fine line displacement or
wrinkles occur.
Display/adj/set range -20 to 20
Unit %
Default value 0
TFL-RTC Set delvry dest at rcvry after tray full
Lv.1 Details To select the delivery destination for a job with multiple pages after
recovering the Delivery Tray that reaches the full level.
When 0 (default) is set, a job is output from the delivery destination
again from which the last job was delivered.
When 1 is set, a job is output from the delivery destination which
priority is set as high at "Output Tray Settings" in user mode.
Use case When changing the delivery tray
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Output from the tray from which the last job was output.
1: Output from the delivery destination which priority is high among
the delivery trays.
Default value 0
8
Service Mode > COPIER > OPTION > FEED-SW
8 Service Mode > COPIER > OPTION > FEED-SW
COPIER > OPTION > FEED-SW
USZ-FEED ON/OFF Job set/ppr source ppr size chck
Lv.1 Details To set whether to check if the paper size set for the job matches the
paper size set on the paper source.
When 1 is set, papers are picked up without checking even user
defined size papers that differ from the job setting size are set on a
paper source.
Use case When forcibly picking up papers even the paper size setting differs
between a job and a paper source
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
MFENV-K2 Lift Plt press:MP Tr pckup, envlp(Kaku2)
Lv.1 Details To set the Lifting Plate pressure mode when feeding an envelope
(Kakugata 2) from the Multi-purpose Tray.
When 0 is set, the Lifting Plate applies pressure to the envelope
once.
When 1 is set, pressure is applied twice and the feeding power is
increased.
Use case - At installation
- When jams frequently occur
Adj/set/operate method Enter the setting value, and then press OK key.
Caution When applying pressure twice, jam may occur frequently with
Yougata-type envelope.
Display/adj/set range 0 to 1
0: Pressure is applied once, 1: Pressure is applied twice
Default value 0
MFENV-N3 Lift Plt press:MP Tr pckup, envlp(Naga3)
Lv.1 Details To set the Lifting Plate pressure mode when feeding an envelope
(Nagagata 3) from the Multi-purpose Tray.
When 0 is set, the Lifting Plate applies pressure to the envelope
once.
When 1 is set, pressure is applied twice and the feeding power is
increased.
Use case - At installation
- When jams frequently occur
Adj/set/operate method Enter the setting value, and then press OK key.
Caution When applying pressure twice, jam may occur frequently with
Yougata-type envelope.
Display/adj/set range 0 to 1
0: Pressure is applied once, 1: Pressure is applied twice
Default value 0
8-185
8-185