Table Of Contents - Keysight PD1500A Installation And Use Manual

Contents
1 General Information
Incoming Inspection for Double-Pulse Test Fixture and Modules . . . . . . . . . . 16
PD1000A Test Fixture for the PD1500A Double-Pulse Test System . . . . . . . . . 17
Standard Double-Pulse Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Clamp Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Reverse Recovery Double-Pulse Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2 Double-Pulse Test Preparation
Mounting the Coaxial Shunt Resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Install Test Modules on the Main Test Fixture . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Clamp Circuit Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Gate Drive Modules (Low-Side and High-Side) . . . . . . . . . . . . . . . . . . . . . . . . 34
Connect Oscilloscope Probes to Oscilloscope . . . . . . . . . . . . . . . . . . . . . . . . . 37
Coaxial Shunt Resistor and PD1000-60002 Protection Probe . . . . . . . . . . . . . 41
Keysight DPT Test Fixture User Guide
Preparation for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Static-safe Handling Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connections on Back of Test Fixture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Test Fixture Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Use these Double-Pulse Test Modules and Oscilloscope Probes . . . . . . . . 21
Use these Double-Pulse Test Modules and Oscilloscope Probes . . . . . . . . 22
Use these Double-Pulse Test Modules and Oscilloscope Probes . . . . . . . . 23
Connect the Waveform Generator to the Double-Pulse Test Fixture . . . . . 25
Connect Heater and Thermocouple to Device Under Test (Optional) . . . . . 26
Second Thermocouple Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Install Double-Pulse Test Modules on the Test Fixture in this order:. . . . . . 30
For both TO-247 and D
When to use the PD1000-66505 Clamp Circuit Module . . . . . . . . . . . . 33
Using the Clamp Circuit Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
How the Clamp Circuit Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Connect Probes to the Double-Pulse Test Modules. . . . . . . . . . . . . . . . . . . 38
Connect the 10076C High Voltage Probe . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Cleaning the Protection Probe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
2
PAK Device DUT types: . . . . . . . . . . . . . . . . . . 31
xiii