Barco HDF W Series Service Manual page 331

LPS failure fan 1 38
LPS failure fan 1 & 2 35
LPS failure fan 2 39
LPS failure pfc driver 39
LPS failure power stage driver
LPS internal error 38
LPS internal voltage error
LPS invalid parameters
LPS mains voltage too high
LPS mains voltage too low
LPS no lamp ignition detected
LPS output current too high
LPS output current too low
LPS output power too high
LPS output power too low
Lps read failed 93
Lps reply no ack 94
LPS requested output power too high with low mains voltage
LPS start-up fail LPS power stage
LPS start-up fail PFC power stage
LPS Temperature ambient too high
LPS temperature heatsink output diode too high
LPS temperature primary heatsink 1 too high
LPS temperature primary heatsink 2 too high
LPS temperature transformer too high
Lps write failed 93
Lseek failed 92
Lsm read failed 94
Lsm reply no ack 94
Lsm write failed 93
Mains voltage high 74–75
Mains voltage low 74
Mcb read failed 93
Mcb reply no ack 94
Mcb write failed 93
Mmap failed 93
Motor board calibration
No dmx shutdown 89
No memory 91
no signal shutdown 89
Non blocked signal 91
Opening shutter failed 84
Overtemp 72
Overtemperature dimming
Port timeout 91
Power interrupt 71
Power supply primary DCDC temp high
Power supply primary DCDC temp low
Power supply primary DCDC temp open
Power supply primary PFC temp high
Power supply primary PFC temp low
Power supply primary PFC temp open
Power supply secondary temp high
Power supply secondary temp low
Power supply secondary temp open
Power supply secondary temp short
Projector type invalid 90
Pump voltage high 75
Pump voltage low 75
Read failed 92
Read lamp status failed
Reading lamp info module
Recieve Overflow 92
Recieve Parity 92
Red DMD temp high 54–55
Red DMD temp low 53–54
Red DMD temp open 55
Red DMD temp short 56
Red form. start failed 33
Rod in temp high 66
Rod in temp low 65–66
Rod in temp open 67
Rod in temp short 67
Rs485 selection 91
Setting FCB mode 53
Setting XLR control 53
R5905312 HDF W SERIES 24/01/2013
39
38
35
38
37
35
36
36
35
35
35
35
36–37
37
36
36
37
84
88
69
68–69
69
70
69–70
70–71
67–68
67
68
68
35
87
Shutter current too high
Shutter time out 85
Spi Ioctl failed 92
Storage: restoring without any preceding storing
Storage: successful restoring
Storage: successful restoring with fall back mgt file
Storage: unsuccessful restoring
Tilt orientation invalid
Tilt rotation not allowed
Transmit overflow 92
Usb restoring settings failed
Usb saving settings failed
Vertical lens shift driver
Vertical lens shift end of range
Vertical lens shift stopped
Watchdog 72
Write failed 92
Xlr overload 76
38
Error code number 33–96
100000 91
100001 91
100002 91
100003 91
100004 91
100005 91
100006 91
100007 91
100008 91
100009 91
100010 91
100011 92
100012 92
100013 92
100014 92
100015 92
100016 92
100017 92
100018 92
100019 92
100020 92
100021 92
100022 93
100023 93
100024 93
100025 93
100026 93
100027 93
100028 93
100029 93
100030 93
100031 93
100032 93
100033 94
100034 94
100035 94
100036 94
100037 94
100038 94
100039 94
100040 94
100041 94
100042 94
100043 94
100044 95
100045 95
100046 95
100047 95
100048 95
100049 95
100050 95
100051 95
100052 95
100053 95
100054 95
100055 96
100056 96
86
96
96
96
89
87–88
90
90
85
84–85
87
Index
96
327