Barco HDF W series Quick Start Manual

LED and Button indication chart
10/100 BASE-T
4
1 2 3
6 7 8 9
ETH
ACT PWR LMP
RGB
PATTERN WINDOW PIP
10/100 ERR IR
STBY PAUSE TEXT AUTO
Button panel Communication interface
LED or Button Color status Description
Standby button RED on Projector is in standby
RED toggles on/off Projector startup failed
GREEN toggles on/off Projector starts up
GREEN on Projector is on
WHITE toggles on/off Projector goes from/to ECO standby
Pause button RED on Shutter is closed
GREEN on Shutter is open
Dimmed WHITE Shutter is closed, projector in standby
Full WHITE Shutter is undefined
Full WHITE toggles on/ Shutter is closed during reset format-
off ter
PWR (power LED) Off Projector powers up
RED Projector is in standby
ORANGE Projector is in ECO standby
GREEN Projector is on
LMP (lamp LED) Off Lamp is off
RED No lamp inserted
ORANGE Lamp is on in ECO mode
GREEN Lamp is on in normal mode
GREEN-ORANGE Lamp is on in CLO mode
ERR (error LED) Off No error
RED toggles on/off Error
ORANGE toggles on/off Warning
IR RED IR signal received
GREEN IR signal acknowledged
FLMW-Quickstartguide4.indd 1
HDF W series
Mounting the lens
WIFI
SEL
ACT
B
•
Remove foam in lens opening.
•
Place lens holder in unlock position. Handle A
towards socket B.
Local LCD screens
Overview window
(A)
•
Main source
•
PiP source
•
IP address
•
Customer ID
•
Lamp status
•
Mains voltage
•
Ambient temperature
•
Text status (OSD)
Quick start guide
A
•
Gently insert the lens in such a way that the
lens connector matches the socket B.
•
Insert the lens until the connector seats into
the socket.
•
Secure the lens in the lens holder. Move
handle A into the lock position (away from
socket B).
A A B
1 1
2 2
Lamp overview window
(B)
•
Number of strikes
•
Run time (hours)
•
Remaining run time (hours)
•
% lamp used
Common parts
•
Error and warning area (1)
•
Projector status (2)
Green: projector works correctly
Red cross: projector has errors
Yellow triangle: projector has warnings
Quick setup and operation
The following summarizes HDF setup and opera-
tion. For errorfree installation always refer to the
User Guide.
Connect power. Ensure that the power (200-
1
240 V @ 50/60hz) is properly connected to the
power input.
Connect available sources to the appropriate
2
input terminal.
Power on. Turn the mains switch to on.
3
Start up sequence starts. Local LCD displays a
4
start up screen
Standby button changes from red to green
5
when pressed.
Image of the latest selected input appears.
6
•
Check if lens touches the front plate of the lens
Adjust the lens settings by pressing the LENS
7
holder.
button or via the direct lens keys on the RCU
•
Check if the lens is really secured by trying to
Auto image can load automatically the correct
8
pull the lens out of the lens holder.
file. The manual selection can be done via menu
•
Put the safety cable around the lens between
or other control systems.
the motor part and the mounting flange.
Mount the clamp. Orientation of the unit is set as standard in
9
table front projection mode. Change the projec-
tor set up in the ALIGNMENT > ORIENTATION
menu.
If geometrical distortion occurs this can
10
be corrected with the Warping settings in the
ALIGNMENT menu.
Tuning the image can be done in the IMAGE
11
C
menu or via the image settings on the RCU
Picture-in-Picture control can be done in the
12
LAYOUT menu or via the PiP button.
Lamp management in the LAMP menu.
13
1
2
Switching off the unit can be done by pressing
14
the STBY button for 3 sec. An aftercool up to
About window
(C)
300 sec will start.
•
Package version in use
•
Mgr Software in use
Support
•
GUI Software in use
www.barco.com/esupport
USA
EMEA
APAC
+1 866 374 7878
+32 56 368019
+86 400 88 22726
16-11-2012 11:21:16