Siemens SIMOCODE pro C System Manual page 406

Index
Sequence for connecting PROFIBUS DP to the
basic unit, 248
Sequence for mounting the bus terminal on the
SIMOCODE pro S basic unit, 188
Sequence for wiring the removable terminals for
SIMOCODE pro V PN / pro V EIP / pro V PN GP
basic units, 207
Service and support, 313
Service and Support, 327
Service data, 42, 60
Set time (= PC time), 129
Setting IP parameters and device name on a
plant-specific basis, 271
Setting IP parameters and EtherNet/IP device name
with SIMOCODE ES via PC cable, 271
Setting IP parameters and PROFINET device name on
a plant-specific basis, 261
Setting IP parameters and PROFINET device name
with SIMOCODE ES (TIA Portal) via PC cable, 261
Setting the DM-F DIP switches, 148
Setting the Modbus RTU address via addressing
plug, 266
Setting the Modbus RTU address with
SIMOCODE ES (TIA Portal), 267
Setting the PROFIBUS DP address via
SIMOCODE ES (TIA Portal), 258, 258
Setting the PROFIBUS DP address via the addressing
plug, 258, 258
Setting the PROFIsafe address on DM-F
PROFIsafe, 258, 262
Setting the rated motor current, 305
Setting the time with SIMOCODE ES (TIA Portal), 263
Setting the timer with SIMOCODE ES, 273
Short-circuit protection according to IEC 60947-4-1,
type of coordination 2, 309
Short-circuit protection with fuses for motor feeders for
short-circuit currents up to 100 kA and 690 V, 364
Signal conditioning, 58
SIMOCODE pro C, 10, 24, 66
SIMOCODE pro C basic unit, 82
SIMOCODE pro S, 10, 24, 66
SIMOCODE pro S basic unit, 82
SIMOCODE pro V EIP, 68
SIMOCODE pro V EIP (EtherNet/IP), 10
SIMOCODE pro V High Performance basic unit, 83
SIMOCODE pro V MR, 67
SIMOCODE pro V MR (Modbus RTU), 10
SIMOCODE pro V PB, 67
SIMOCODE pro V PB (PROFIBUS), 10
SIMOCODE pro V PN, 67
SIMOCODE pro V PN (PROFINET), 10
SIMOCODE pro V PN GP, 66
406
SIMOCODE pro V PN GP (PROFINET), 10
SIMOCODE pro V PN GP basic unit, 83
SIMOCODE pro V PN GP, 24
Single-phase systems, 145
Snap-on mounting, 185
Soft reversing starter, 42
Soft starter, 42, 53
Soft starter with reversing contactor, 53
Software, 80
Software for configuring and commissioning, 266
Solenoid valve, 42, 53
Solenoid valve control, 83
Stalled positioner, 293
Stalled rotor, 292
Stalled rotor protection, 41, 47
Standard functions, 57
Standards, 329
Star networks, 144
Star-delta reversing starter, 42, 53
Star-delta starter, 42, 53, 83
Startup parameter block active, 291
States of the status LEDs / contactor controls during
testing, 310
Statistics/Maintenance, 109
Statistics/maintenance, operator panel with display, 98
Status - cooling down period active, 298
Status display, 109
Status display for fieldbus communication, 120
Status DM-F enabling circuit, 298
Status emergency start executed, 298
Status motor protection/motor control, operator panel
with display, 96
Status test position (TPF), 298
Stop time >, 298
Storage clips for labeling strips, 90
Stripped lengths, 197
Support Request, 15, 18, 287
System interface
Connection of cables, 244
Connection of system components, 244
Operator panel, 243
Operator panel with display, 243
System interface analog module, 352
System interface cover, 177, 237, 243
System interface ground-fault module, 354, 355
System interface main circuit current measuring
modules / current/voltage measuring
modules, 340, 342
System interface multifunction module, 357
System interface temperature module, 356
System interfaces, 84, 236, 332
System interfaces decoupling module, 345
System Manual, 05/2019, A5E40507475002A/RS-AD/004
SIMOCODE pro