Siemens SIMOCODE pro C System Manual page 401

Debouncing time, 147
Decoupling module, 135, 142
Decoupling module (DCM), 71
Decoupling module connection example, 221
Decoupling module in different power systems, 143
Degree of protection (according to IEC 60529), 329
Delta configurations, 145
Device addressing, 266
Device I/Os, 109
Device I/Os, operator panel with display, 102
Device replacement, 176
Device series, 10, 24
Device startup when the "initialization module"
parameter is activated, 164
Diagnostics data, 42, 60
Diagnostics via LED display, 264, 274
Diagnostics via LED display on the basic unit and on
the operator panel, 259
Diagnostics via LED display on the modules DM-F
Local or DM-F PROFIsafe, 259
Diagram of the diagnostics data in the 3UF50
compatibility mode, 181
Diagram of the receive and send data in 3UF50
compatibility mode, 180
Digital module
DM-F Local, 52
DM-F PROFIsafe, 52
Digital module (DM), 147
Digital module connection example, 211
Digital module DM-F Local connection example, 224
Digital module DM-F PROFIsafe connection
example, 225
Digital module function multifunction module, 357
Digital modules, 72
Digital modules (DM), 146
Digital modules, fail-safe, 72
Dimension drawing initialization module, 172
Dimension drawing Y connecting cable, 172
Dimension drawings, 13
DIP switch DM-F LOCAL, 350
DIP switch DM-F PROFIsafe, 351
Direct starter (direct-on-line starter), 33, 42, 53, 83
Disclaimer of liability, 11
Display, 332
Display elements of the operator panel with display, 92
Display of all pending faults, 130
Display of all pending status information, 130
Display of all pending warnings, 130
Display of measured values in the measured values
display, 115
Display of statistical and maintenance-relevant
information on the statistics/maintenance display, 119
SIMOCODE pro
System Manual, 05/2019, A5E40507475002A/RS-AD/004
Display of the operator panel with display, 361
Display settings, 110
Display settings, operator panel with display, 104
Displays of the operator panel with display, 92, 109
Displays the current status of all device I/Os, 122
DM-F DIP switch settings, 147
DM-F feedback circuit, 293
DM-F LOCAL digital module, 146
DM-F PROFIsafe digital module, 146
DM-F safety-related tripping, 293
DM-F system interfaces, 148, 148
DM-F test requirement, 293
DM-F wiring, 293
DM-FL actual and set configuration different, 293
DM-FL configuration mode, 294
DM-FL cross-circuit, 294
DM-FL simultaneity, 293
DM-FL waiting for start-up test, 294
DM-FP Prm error, 294
Door adapter, 77, 177
Double 0, 294
Double 1, 294
Dry-running – pump, 299
Dry-running protection – error, 300
Dry-running protection for centrifugal pumps, 48
Dry-running protection for centrifugal pumps by active
power monitoring, 335, 339
Dry-running protection for centrifugal pumps by means
of active power monitoring, 41, 61, 314
E
Electrical life of the relay outputs digital modules
DM-F, 348
EMC stability according to IEC 60947-1, 330
Emergency start, 57
End position, 294
Environmental conditions, 325
EPLAN macros, 13
Error buffer, 110
Ethernet connector, 249
ETHERNET interface, basic unit, 337
EtherNet/IP, 56
Evaluation of the short-circuit detection of the sensor
cable, 308
Event memory, 111, 290
Event memory, operator panel with display, 107
Example of a tripping characteristic with 3UF710*
current/voltage measuring modules and
3UF711*-1AA00-0 1st generation current/voltage
measuring modules, 306
Index
401