Barco Argus X Terminal User Manual page 154

6.1.6 Combination rules
When extending a system by inserting additional expansion cards into an O
card of different type, the following rules must be checked to see, if the planned configuration is possible.
Functional rules
•
In an O B the number of inserted cards must not exceed 18 expansion cards.
MNI US
•
O S SXGA (
MNI CALER AGX-3002
•
Systems with UGX G
•
Q A V C
UAD NALOG OG IDEO ARD
•
Different types of graphic cards may only be mixed in some cases. Please see in the table below which types
of graphic cards can be mixed in the respective configuration.
type
AGX-digital and AGX-analog
UGX-digital and UGX-analog
AGX and UGX
(1) Within one O
MNI
For best display quality of the video and RGB sources, in addition the following should be considered:
•
Video and RGB windows may not require too much bandwidth, please see section
Overload calculation
There are three criteria V1 1 , V2 and M1. Each of them must be valid, to allow the card to be inserted.
The rule is for each criterion the same. For each card there is a factor that must be multiplied by the amount how
often it is inserted in the O
100, if the configuration shall be allowed.
System base load
AGX G C
RAPHIC ARD
UGX G C
RAPHIC ARD
O S max. SXGA
MNI CALER
O S max. UXGA
MNI CALER
Q A V C
UAD NALOG IDEO ARD
D RGB I C
UAL NPUT ARD
S V C
TREAMING IDEO ARD
optical cables
Maximum allowed:
It is not allowed to configure combinations of cards that do not fullfil the three above
criteria. Otherwise there is the risk to destroy the power supply! !
Barco – Argus X Terminal – DOC-3265-2 – user's manual – Revision 04 – May-2004
) and O S UXGA (
MNI CALER
C and UXGA output must use O
RAPHIC ARD
and D RGB I I C
UAL NPUT ARD
monolithic system
no
no
no
B only cards with the same mode.
US
GB sources, in addition the following should be considered:
B . The system base load must always be added once. The sum may not exceed
MNI US
OmniBus AGS-3013-0/-1 3013-0/-1
V1 V2
6.7
2.5
3.4
1.2
2.2
5.9
5.2
7.3
–
100
8 expansion cards.
) can be mixed.
AGX-3313
S
MNI CALERS
may only be used together with O
OmniBus AGS-3328-0/-1
M1 V1
2.5 8.0
1.4 4.8
6.7 8.0
2.9 0.8
4.4 0.8
2.5 1.7
2.5 1.7
3.7 1.7
0.4 –
100 100
components factors for configuration criteria calculation
________________________________________________________________________
6. Advanced configuration
B or by exchanging a card with a
MNI US
UXGA.
S
MNI CALERS
distributed system
yes (1)
yes (1)
no
4.6.1 The input
V2
5.8 3.0
2.2 1.6
2.9 8.0
1.0 3.4
1.9 5.2
5.0 3.0
4.5 3.0
6.3 4.4
– 0.4
100 100
Table 6-4
cards.
M1
8.0
4.8
8.0
0.8
0.8
1.7
1.7
1.7
–
100
Table 6-5
6-11