Basic Parameters; Menu 0: Basic Parameters - Nidec Unidrive M200 User Manual

Safety Product Mechanical
information information installation
6

Basic parameters

Menu 0 is used to bring together various commonly used parameters for basic easy set up of the drive. All the parameters in Menu 0 appear in other
menus in the drive (denoted by {...}). Menu 22 can be used to configure the parameters in Menu 0.
Parameter ranges and Variable minimum/maximums:
Some parameters in the drive have a variable range with a variable minimum and a variable maximum value which is dependent on one of the
following:
• The settings of other parameters
• The drive rating
• The drive mode
• Combination of any of the above
For more information please see section 11.1 Parameter ranges and Variable minimum/maximums: on page 70.
6.1

Menu 0: Basic parameters

Parameter
01 Minimum Speed
02 Maximum Speed
03 Acceleration Rate 1
04 Deceleration Rate 1
05 Drive Configuration
06 Motor Rated Current
07 Motor Rated Speed**
08 Motor Rated Voltage
***
09
Motor Rated Power Factor
10 User Security Status
11 Start/Stop Logic Select
15 Jog Reference
16 Analog Input 1 Mode
17 Bipolar Reference Enable
18 Preset Reference 1
19 Preset Reference 2
20 Preset Reference 3
21 Preset Reference 4
22 Status Mode Parameter 2
23 Status Mode Parameter 1
24 Customer Defined Scaling
25 User Security Code
Power-up Keypad Control Mode
27
Reference
28 Ramp Mode Select
29 Ramp Enable
30 Parameter Cloning
31 Stop Mode
Dynamic V to F Select
32
Flux Optimisation Select
33 Catch A Spinning Motor
34 Digital Input 5 Select
35 Digital Output 1 Control
Unidrive M200 / M201 Control User Guide
Issue Number: 2
Electrical Getting Basic
installation started parameters
Range
OL
{01.007} 0.00 to Pr 02 Hz
{01.006} 0.00 to 550.00 Hz
{02.011} 0.0 to 32000.0 s / 100 Hz
{02.021} 0.0 to 32000.0 s / 100 Hz
AV (0), AI (1), AV.Pr (2), AI.Pr (3), PrESEt (4), PAd (5),
{11.034}
PAd.rEF (6), E.Pot (7), torquE (8), Pid (9)
{05.007} 0.00 to Drive Rating A
{05.008} 0.0 to 33000.0 rpm
{05.009} 0 to 765 V
{05.010} 0.00 to 1.00
{11.044} LEVEL.1 (0), LEVEL.2 (1), ALL (2), StAtUS (3), no.Acc (4)
{06.004} 0 to 6
{01.005} 0.00 to 300.00 Hz
4-20.S (-6), 20-4.S (-5), 4-20.L (-4),
{07.007} 20-4.L (-3), 4-20.H (-2), 20-4.H (-1), 0-20 (0), 20-0 (1),
4-20.tr (2), 20-4.tr (3), 4-20 (4), 20-4 (5), Volt (6)
{01.010} Off (0) or On (1)
{01.021} 0.00 to Pr 02 Hz
{01.022} 0.00 to Pr 02 Hz
{01.023} 0.00 to Pr 02 Hz
{01.024} 0.00 to Pr 02 Hz
{11.019} 0.000 to 30.999
{11.018} 0.000 to 30.999
{11.021} 0.000 to 10.000
{11.030} 0 to 9999
{01.051} Reset (0), Last (1), Preset (2)
{02.004} Fast (0), Std (1), Std.bst (2), Fst.bst (3)
{02.002}
{11.042} NonE (0), rEAd (1), Prog (2), Auto (3), boot (4)
Coast (0), rp (1), rp.dc I (2), dc
{06.001} I (3), td.dc I (4),
dis (5)
{05.013} 0 to 1
{05.013}
{06.009} dis (0), Enable (1), Fr.Only (2), Rv.Only (3)
{08.035} Input (0), th.Sct (1), th (2), th.Notr (3), Fr (4)
{08.091} 0 to 21
Running the NV Media
Optimization
motor Card
()
RFC-A OL
50Hz default: 50.00 Hz
60Hz default: 60.00 Hz
Maximum Heavy Duty Rating A
50Hz default:
1500.0 rpm
60Hz default:
1800.0 rpm
110V drive: 230 V
200V drive: 230 V
400V drive 50 Hz: 400 V
400V drive 60 Hz: 460 V
575V drive: 575 V
690V drive: 690 V
Off (0) or On (1)
Coast (0), rp (1), rp.dc I
(2), dc I (3), td.dc I (4),
dis (5), No.rp (6)
0
0 to 1
Onboard Advanced
Diagnostics
PLC parameters
Default
()
RFC-A
0.00 Hz RW Num
RW Num
5.0 s / 100 Hz RW Num
10.0 s / 100 Hz RW Num
*
AV (0) RW Txt
RW Num
50Hz default:
1450.0 rpm
RW Num
60Hz default:
1750.0 rpm
RW Num
0.85 RW Num
LEVEL.1 (0) RW Num
0 RW Num
1.50 Hz RW Num
Volt (6) RW Txt
Off (0) RW Bit
0.00 Hz RW Num
0.00 Hz RW Num
0.00 Hz RW Num
0.00 Hz RW Num
4.020 RW Num
2.001 RW Num
1.000 RW Num
0 RW Num
Reset (0) RW Txt
Std (1) RW Txt
On (1) RW Bit
NonE (0) RW Txt
rp (1) RW Txt
RW Num
0 RW Num
dis (0) RW Txt
Input (0) RW Txt
0 RW Num
UL Listing
Type
US
US
US
US
PT US
RA US
US
RA US
RA US
ND PT
US
US
US
US
US
US
US
US
PT US
PT US
US
ND PT US
US
US
US
NC US
US
US
US
US
US
US
29