Nidec Unidrive M200 User Manual page 96

Safety Product Mechanical
information information installation
Parameter
05.001 Output Frequency
05.002 Output Voltage
05.003 Output Power
05.004 Motor Rpm
05.005 D.C. Bus Voltage
05.006 Motor Rated Frequency
05.007 Motor Rated Current
05.008 Motor Rated Speed
05.009 Motor Rated Voltage
05.010 Motor Rated Power Factor
05.011 Number Of Motor Poles*
05.012 Autotune
Dynamic V To F Select / Flux Optimization
05.013
Select
05.014 Control Mode
05.015 Low Frequency Voltage Boost
05.017 Stator Resistance
05.018 Maximum Switching Frequency
05.019 High Stability Space Vector Modulation
05.020 Over Modulation Enable
05.021 Mechanical Load Test Level
05.024 Transient Inductance
05.025 Stator Inductance
05.026 High Dynamic Performance Enable
05.027 Enable Slip Compensation
05.028 Flux Control Compensation Disable
05.029 Saturation Breakpoint 1
05.030 Saturation Breakpoint 3
05.031 Voltage Controller Gain
05.032 Torque Per Amp
05.033 Slip Compensation Limit
05.034 Percentage Flux
05.035 Auto-switching Frequency Change Disable
05.036 Slip Compensation Filter
05.037 Switching Frequency
05.038 Minimum Switching Frequency
05.040 Spin Start Boost
05.042 Reverse Output Phase Sequence
05.059 Maximum Deadtime Compensation
Current At Maximum Deadtime
05.060
Compensation
05.061 Disable Deadtime Compensation
05.062 Saturation Breakpoint 2
05.063 Saturation Breakpoint 4
05.074 Boost End Voltage
05.075 Boost End Frequency
05.076 Second Point Voltage
05.077 Second Point Frequency
05.078 Third point voltage
05.079 Third point frequency
96
Electrical Getting Basic
installation started parameters
Range ()
OL
± 550.00 Hz
0 to 930 V
VM_POWER kW
± 33000.0 rpm
0 to 1190 V
0.00 to 550.00 Hz
0.00 to Drive Rating A
0.0 to 33000.0 rpm
0 to 765 V
0.00 to 1.00
Auto (0) to 32 (16)
0 to 2
0 to 1
Ur.S (0), Ur (1),
Fd (2), Ur.Auto (3),
Ur.I (4), SrE (5),
Fd.tAP (6)
0.0 to 25.0 %
0.0000 to 99.9999 Ω
0.667 (0), 1 (1),
2 (2), 3 (3), 4 (4),
6 (5), 8 (6),
12 (7), 16 (8) kHz
Off (0) or On (1)
Off (0) or On (1)
0.000 to 500.000 mH
0.00 to 5000.00 mH
±150.0 %
Off (0) or On (1)
1 to 30
0.00 to 500.00 Nm/A
0.00 to 10.00 Hz
0 to 1
64 (0), 128 (1),
256 (2), 512 (3) ms
0.667 (0), 1 (1),
2 (2), 3 (3), 4 (4),
6 (5), 8 (6),
12 (7), 16 (8) kHz
0 to VM_MAX_SWITCHING_
FREQUENCY kHz
0.0 to 10.0
Off (0) or On (1)
0.000 to 10.000 µs
0.00 to 100.00 %
Off (0) or On (1)
0.0 to 100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
Running the NV Media
Optimization
motor Card
Default ()
RFC-A OL
50 Hz: 50.00 Hz, 60 Hz: 60.00 Hz
Maximum Heavy Duty Rating (11.032) RW Num
50 Hz: 1500.0
rpm
60 Hz: 1800.0
rpm
110 V drive: 230 V, 200 V drive: 230 V
400 V drive 50Hz: 400 V
400 V drive 60Hz: 460 V
575 V drive: 575 V
690 V drive: 690 V
0 to 3
Ur.I (4)
2 (2), 3 (3), 4 (4),
6 (5), 8 (6), 12 (7),
16 (8) kHz
Off (0)
Off (0)
0 to 100 %
Off (0) or On (1)
100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
10.00 Hz
0.0 to 150.0 %
128 (1) ms
2 (2), 3 (3), 4 (4),
6 (5), 8 (6), 12 (7),
16 (8) kHz
0.667 kHz (0)
0.0 to 100.0 %
0.0 to 100.0 %
50.0 %
50.0 %
55.0 %
55.0 %
75.0 %
75.0 %
Onboard Advanced
Diagnostics
PLC parameters
RFC-A
RO Num ND NC PT FI
RO Num ND NC PT FI
RO Num ND NC PT FI
RO Num ND NC PT FI
RO Num ND NC PT FI
RW Num
50 Hz: 1450.0
rpm
RW Num
60 Hz: 1750.0
rpm
RW Num
0.85 RW Num
Auto (0) RW Num
0 RW Num
0 RW Num
RW Txt
3.0 % RW Num
0.0000 Ω RW Num
3 (3) kHz RW Txt
RW Bit
RW Bit
0 % RW Bit
0.000 mH RW Num
0.00 mH RW Num
Off (0) RW Bit
RW Num
Off (0) RW Bit
50.0 % RW Num
75.0 % RW Num
1 RW Num
RO Num ND NC PT
RW Num
RO Num ND NC PT
0 RW Num
RW Txt
RO Txt ND NC PT
2 kHz (2) RW Txt
1.0 RW Num
Off (0) RW Bit
RO Num
RO Num
Off (0) RW Bit
0.0 % RW Num
0.0 % RW Num
RW Num
RW Num
RW Num
RW Num
RW Num
RW Num
Unidrive M200 / M201 Control User Guide
Issue Number: 2
UL Listing
Type
RA US
RA US
US
RA US
RA US
US
NC
US
US
US
RA US
RA US
US
US
US
RA US
RA US
US
US
US
US
US
US
US
US
US
RA
US
US
NC PT US
NC PT US
US
US
US
US
US
US
US
US
US