Nidec Unidrive M200 User Manual page 99

Safety Product Mechanical
information information installation
Parameter
06.001 Stop Mode
06.002 Limit Switch Stop Mode
06.003 Supply Loss Mode
06.004 Start/Stop Logic Select
06.006 Injection Braking Level
06.007 Injection Braking Time
06.008 Hold Zero Frequency
06.009 Catch A Spinning Motor
06.010 Enable Conditions
06.011 Sequencer State Machine Inputs
06.012 Enable Stop Key
06.013 Enable Auxiliary Key
06.014 Disable Auto Reset On Enable
06.015 Drive Enable
06.016 Date
06.017 Time
06.018 Day Of Week
06.019 Date/Time Selector
06.020 Date Format
06.021 Time Between Filter Changes
Filter Change Required /
06.022
Change Done
06.023 Time Before Filter Change Due
06.024 Reset Energy Meter
06.025 Energy Meter: MWh
06.026 Energy Meter: kWh
06.027 Energy Cost Per kWh
06.028 Running Cost
06.029 Hardware Enable
06.030 Run Forward
06.031 Jog Forward
06.032 Run Reverse
06.033 Forward/Reverse
06.034 Run
06.035 Forward Limit Switch
06.036 Reverse Limit Switch
06.037 Jog Reverse
06.038 User Enable
06.039 Not Stop
06.040 Enable Sequencer Latching
06.041 Drive Event Flags
06.042 Control Word
06.043 Control Word Enable
06.045 Cooling Fan control
06.047 Input Phase Loss Detection Mode
06.048 Supply Loss Detection Level
06.051 Hold Supply Loss Active
06.052 Motor Pre-heat Current Magnitude
06.058 Output Phase Loss Detection Time
06.059 Output Phase Loss Detection Enable
06.060 Standby Mode Enable
06.061 Standby Mode Mask
06.071 Slow Rectifier Charge Rate Enable
06.073 Braking IGBT Lower Threshold
Unidrive M200 / M201 Control User Guide
Issue Number: 2
Electrical Getting Basic
installation started parameters
Range ()
OL
CoASt (0), rP (1),
rP.dc I (2), dc I (3),
td.dc I (4),
diS (5)
StoP (0), rP (1)
diS (0), rP.StoP (1), ridE.th (2), Lt.StoP (3)
0 to 6
0.0 to 150.0 %
0.0 to 100.0 s
Off (0) or On (1)
diS (0), EnAbLE (1), Fr.OnLy (2), rv.OnLy (3)
0 to 4087
0 to 127
Off (0) or On (1)
diS (0), Fd.rv (1), rEv (2)
Off (0) or On (1)
Off (0) or On (1)
00-00-00 to 31-12-99
00:00:00 to 23:59:59
Sun (0), Non (1), tuE (2), UEd (3),thu (4),
Fri (5), SAt (6)
SEt (0), Po.uP (1), run (2), Acc.Po (3),
rE.PAd (5), SLot.1 (6)
Std (0), US (1)
0 to 30000 Hours
Off (0) or On (1)
0 to 30000 Hours
Off (0) or On (1)
±999.9 MWh
±99.99 kWh
0.0 to 600.0
± 32000
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
0 to 3
0 to 32767
0 to 1
0 to 5
FuLL (0), rIPPLE (1), diS (2)
0 to VM_SUPPLY_LOSS_LEVEL V
Off (0) or On (1)
0 to 100 %
0.5 (0) to 4 (3) s
Off (0) or On (1)
Off (0) or On (1)
0 to 15
Off (0) or On (1)
0 to VM_DC_VOLTAGE_SET V
Running the NV Media
Optimization
motor Card
Default()
RFC-A OL
CoASt (0), rP (1),
rP.dc I (2), dc I (3),
td.dc I (4),
diS (5), No.rP (6)
110 V drive: 205 V,
200 V drive: 205 V
400 V drive: 410 V,
575 V drive: 540 V
690 V drive: 540 V
110 V drive: 390 V,
200 V drive: 390 V
400 V drive: 780 V,
575 V drive: 930 V
690 V drive: 1120 V
Onboard Advanced
Diagnostics
PLC parameters
RFC-A
rP (1) RW Txt
rP (1) RW Txt
diS (0) RW Txt
0 RW Num
100.0 % RW Num
1.0 s RW Num
Off (0) RW Bit
diS (0) RW Txt
RO Bin
RO Bin
Off (0) RW Bit
diS (0) RW Txt
Off (0) RW Bit
On (1) RW Bit
RW Date
RW Time
RO Txt
Po.uP (1) RW Txt
Std (0) RW Txt
0 Hours RW Num
RW Bit
RO Num
Off (0) RW Bit
RO Num
RO Num
0.0 RW Num
RO Num
RO Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
0 RW Bin
0 RW Bin
0 RW Num
2 RW Num
FuLL (0) RW Txt
RW Num
Off (0) RW Bit
0 % RW Num
0.5 (0) s RW Txt
Off (0) RW Bit
Off (0) RW Bit
0 RW Bin
Off (0) RW Bit
RW Num
UL Listing
Type
US
US
US
US
RA US
US
US
US
ND NC PT
ND NC PT
US
US
US
US
ND NC PT
ND NC PT
ND NC PT
US
US
US
ND NC
ND NC PT PS
ND NC PT PS
ND NC PT PS
US
ND NC PT
ND NC PT
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
US
NC
NC
US
US
US
RA US
NC
US
US
US
US
US
US
RA US
99