Nidec Unidrive M200 User Manual page 113

Safety Product Mechanical
information information installation
Parameter
10.059 Trip 9 Date
10.060 Trip 9 Time
10.061 Braking Resistor Resistance
10.064 Remote Keypad Battery Low
10.065 Autotune Active
10.066 Limit Switch Active
10.068 Hold Drive Healthy On Under Voltage
10.069 Additional Status Bits
10.070 Trip 0 Sub-trip Number
10.071 Trip 1 Sub-trip Number
10.072 Trip 2 Sub-trip Number
10.073 Trip 3 Sub-trip Number
10.074 Trip 4 Sub-trip Number
10.075 Trip 5 Sub-trip Number
10.076 Trip 6 Sub-trip Number
10.077 Trip 7 Sub-trip Number
10.078 Trip 8 Sub-trip Number
10.079 Trip 9 Sub-trip Number
10.080 Stop Motor
10.081 Phase Loss
10.090 Drive Ready
10.101 Drive Status
10.102 Trip Reset Source
10.103 Trip Time Identifier
10.104 Active Alarm
10.106 Potential Drive Damage Conditions
10.107 Low AC Alarm
10.108 Reversed cooling fan detected
RW Read / Write RO Read only
ND No default value NC Not copied
IP IP address Mac Mac address
Unidrive M200 / M201 Control User Guide
Issue Number: 2
Electrical Getting Basic
installation started parameters
OL
00-00-00 to 31-12-99
00:00:00 to 23:59:59
0.00 to 10000.00 Ω
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Inh (0), rdy (1), StoP (2), rES (3),
rES (4), S.LoSS (5), rES (6),
dc.inJ (7), rES (8), Error (9),
ActivE (10), rES (11), rES (12),
rES (13), HEAt (14), UU (15)
-2147483648 to 2147483647 ms
NonE (0), br.rES (1), OV.Ld (2),
rES (3), d.OV.Ld (4), tuning (5),
LS (6), rES (7), rES (8), OPt.AL (9),
rES (10), rES (11),
rES(12), Lo.AC (13), I.AC.Lt (14),
24.LoSt (15)
Off (0) or On (1)
Off (0) or On (1)
Num Number parameter Bit
PT Protected parameter RA
Date Date parameter Time
Running the NV Media
Optimization
motor Card
Range () Default ()
RFC-A OL
0 to 2047
0 to 65535
0 to 65535
0 to 65535
0 to 65535
0 to 65535
0 to 65535
0 to 65535
0 to 65535
0 to 65535
0 to 65535
0 to 1023
0 to 3
Bit parameter Txt Text string
Rating dependent US User save
Time parameter SMP Slot,menu,parameter
Onboard Advanced
Diagnostics
PLC parameters
RFC-A
RO Date ND
RO Time ND
0.00 Ω RW Num
RO Bit ND
RO Bit ND
RO Bit ND
Off (0) RW Bit
RO Num ND
RO Num ND
RO Num ND
RO Num ND
RO Num ND
RO Num ND
RO Num ND
RO Num ND
RO Num ND
RO Num ND
RO Num ND
RO Bit ND
RO Bit ND
RO Bit ND
RO Txt ND
RO Num ND
RO Num ND
RO Txt ND
RO Bin ND
RO Bit ND
RO Bit ND
Bin Binary parameter
PS Power-down save
Chr Character parameter
UL Listing
Type
NC PT PS
NC PT PS
US
NC PT
NC PT
NC PT
US
NC PT
NC PT PS
NC PT PS
NC PT PS
NC PT PS
NC PT PS
NC PT PS
NC PT PS
NC PT PS
NC PT PS
NC PT PS
NC PT
NC PT
NC PT
NC PT
NC PT PS
NC PT
NC PT
NC PT PS
NC PT
NC PT
FI Filtered
DE Destination
Ver Version number
113