Setting The Assignment Of Macro Operation Buttons; Assigning Keys To The Dsk1 And Dsk2 Buttons In The Downstream Key/Fade-To-Black Control Block; Assigning Keys To The Independent Key Transition Control Block (Simple Type) - Sony MVS-8000X User Manual

Setting the Assignment of Macro
Operation Buttons
Notes
This setting is disabled for the CCP-9000A.
To switch the [UNDO] button on a simple type Flexi Pad
control block to a [MCRO] button for macro operation, use
the following procedure.
1
In the Panel >Config >Link/Program Button menu,
press [Flexi Pad Module].
The Flexi Pad Module menu appears.
2
Select the assignment of the [UNDO] button in the
simple type Flexi Pad control block from the <UNDO
Button Assign> group.
UNDO: use as an [UNDO] button.
MACRO: use as a [MCRO] button.
Assigning Keys to the DSK1 and
DSK2 Buttons in the Downstream
Key/Fade-to-Black Control Block
It is possible to select the key used for downstream key/
fade-to-black control block operations.
Notes
This operation cannot be done in the CCP-9000A.
1
In the Panel >Config >Link/Program Button menu,
press [DSK/FTB Module].
The DSK/FTB Module menu appears.
The left side of the status area shows the DSK1 and
DSK2 buttons, and the right side shows a list of keys
to be assigned.
2
Press the indication (DSK1, DSK2) of the button for
the assignment.
The button you pressed changes to reverse video.
3
Using any of the following methods, select the key to
be assigned.
• Press directly on the list.
• Press the arrow keys to scroll the reverse video
cursor.
• Turn the knob.
Knob Parameter Adjustment
1 Key No Selection of key
assigned to
button
4
Press [Set], to confirm the selection.
This assigns the selected key to the key delegation
button.
To return the key delegation button assignment
to the factory default state
In the DSK/FTB Module menu, press [Default].
This returns the key delegation assignment to the factory
default state.
Assigning Keys to the Independent
Key Transition Control Block (Simple
Type)
It is possible to select the keys that can be used in an
independent key transition control block (simple type)
operation.
Notes
This operation cannot be done in the CCP-9000A.
The control panel comprises a main base for installing the
principal switcher bank control blocks, and an extension
section for extended control blocks. The independent key
transition control block (simple type) can be installed in
either, but the assignable keys differ as follows.
When the independent key transition control
block (simple type) is installed in the main base
Select the keys to be assigned from the following.
1)
• Key1, 2 (keys 1 and 2)
1)
• Key3, 4 (keys 3 and 4)
1)
• Key5, 6 (keys 5 and 6)
1)
• Key7, 8 (keys 7 and 8)
• DSK1, 2 (downstream keys 1 and 2)
• DSK3, 4 (downstream keys 3 and 4)
• DSK5, 6 (downstream keys 5 and 6)
• DSK7, 8 (downstream keys 7 and 8)
• N/A (no assignment)
1) The M/E bank depends on the settings in the M/E Assign menu where the
independent key transition control block is installed.
When the independent key transition control
block (simple type) is installed in the extension
section
Select the keys to be assigned from the following.
• M/E-1 Key1, 2
• M/E-1 Key3, 4
• M/E-1 Key5, 6
• M/E-1 Key7, 8
Overall Control Panel Settings (Config Menu)
Setting values
1 to 40
493