Dme Wipe Pattern Variation And Modifiers - Sony MVS-8000X User Manual

Pattern Effects
groups
Sparkle The new video appears over the old video with a nonlinear
effect applied, such as broken glass, explosion, or melt.
Next this returns to the original video as the effect gradually
reduces.
Split slide The new video appears in strip form while sliding
interleaved in the opposite direction over the old video.
Mosaic In the first half of the transition, a mosaic is gradually
applied to the old video, then at the 50% point the inner
image changes to the new video. In the second half, the
mosaic effect on the new video is gradually reduced,
returning to the original image at 100%.
Defocus In the first half of the transition, the old video is gradually
defocused, then at the 50% point the inner image changes
to the new video. In the second half, the defocusing effect
on the new video is gradually reduced, returning to the
original image at 100%.
Brick • In two-channel mode, a brick such that the side surface is
visible slides in over the old video, then rotates so that the
new video can be seen.
• In three-channel mode, a brick appears over the old video
as the image is expanding and rotating, and switches to
the new video.
User Using a DME keyframe effect created with a keyframe
programmable operation, this executes a DME wipe.
DME
For details of creating keyframe effects, see "Creating User
Programmable DME Patterns" (page 153).
Notes
In an independent key transition, the following patterns
can be used.
Execution mode DME wipe patterns that can be used
One-channel mode Slide, split, squeeze, door, 2D trans, 3D
trans, frame in-out, page turn, page roll,
mirror, sphere, character trail, wave,
ripple, split slide, sparkle, user
programmable DME
Two-channel mode Page turn, page roll
DME Wipe Pattern Variation and
Modifiers
You can modify the selected DME wipe pattern in the
same way as an ordinary wipe pattern, as follows.
For the setting operations, see "Setting DME Wipe
Modifiers" (page 146).
Direction: You can set the DME wipe direction to normal,
reverse, or alternating normal/reverse (see page 146),
except for a key transition, which is always in normal/
reverse mode. However, a key transition can only be
specified when the following patterns are selected, and
142
Overview
Pattern numbers
One-channel Two-channel
mode mode
1391, 1393, —
1394, 1396,
1398, 1399
1384 to 1389 —
1701 —
1702 —
— 2801 to 2804,
2811 to 2814
1901 to 1999 2901 to 2999
when other patterns are selected, this is fixed, as
normal/reverse.
Patterns: 1204, 1207, 1221 to 1224
Edge: You can apply a border or soft border (see page
146).
In the case of those user programmable DME patterns
for keys in which an edge has already been applied to
the effect, the behavior is as follows.
• When the DME wipe edge setting is on, only part of
the edge applied in the effect is enabled, and that
portion can be adjusted (see page 146).
• When the DME wipe edge setting is off, the edge
applied in the effect is enabled as is.
Positioner: You can move the DME wipe pattern or center
of the effect to an arbitrary position. Using the position
select function, you can also instantaneously move the
pattern.
• 1031
When this pattern number is selected, with the
progress of the transition the pattern center
automatically moves initially from the set position
toward the center of the screen (see page 146). In
other words, the effect obtained is the same as in a
normal wipe with the positioner set to "AUTO
CENTER".
• 1201 to 1208, 1221 to 1224, 1251
When these pattern numbers are selected, you can
Three-channel
mode
—
—
—
—
3601
3901 to 3999