Automatically Naming And Saving To Frame Memory; Selecting The Bank To Make The Settings - Sony MVS-8000X User Manual

Automatically Naming and Saving to
Frame Memory
In the Switcher >Key/Wipe/FM/CCR menu, press [FM
Auto Store], turning it on.
Selecting the Bank to Make the
Settings
In the following procedures, select the bank to which the
settings apply using any of the following methods, then
make the settings.
• Press directly on the list in the status area.
• Press the arrow keys to scroll the reverse video cursor.
• Turn the knob.
Knob Parameter Adjustment
1 Bank M/E or P/P selection
to which settings
apply
The selected bank appears in reverse video.
Selecting the key memory mode
In the <Key Memory> group of the Switcher >Key/Wipe/
FM/CCR menu, select one from Full (full mode)/Simple
(simple mode)/Off.
For more details, see "Key Memory" in Chapter 4
(Volume 1).
Selecting the processing order of masks
and borders
In the <Mask/Border Process> group of the Switcher
>Key/Wipe/FM/CCR menu, select one of the following.
Mask >Border: Apply the Mask effect, then apply the
Border effect.
Border >Mask: Apply the Border effect, then apply the
Mask effect.
Selecting the key priority operation mode
In the <Key Priority> group of the Switcher >Key/Wipe/
FM/CCR menu, select one of the following.
Normal: The key priority sequence can be varied freely.
Fix: Fixed at currently set priority sequence.
Setting the operation mode of the key bus
[XPT HOLD] button
In the <Xpt Hold Mode> group of the Switcher >Key/
Wipe/FM/CCR menu, select any of the following. This
setting is applied for the attributes of snapshots as well as
the operation mode of [XPT HOLD] button.
Key Disable: The [XPT HOLD] button of the key bus
functions not only as a cross-point hold button but also
as a key disable button. When the [XPT HOLD] button
is on, recalling a snapshot or keyframe effect does not
reflect the key settings, including the cross-point
selection information.
Key Disable with Status: Same as [Key Disable], and
further disables the reflection of the key on/off status.
Xpt Hold: The [XPT HOLD] button of the key bus
functions as a cross-point hold button. When the [XPT
HOLD] is on, recalling a snapshot or keyframe effect
does not reflect the cross-point selection information.
To change the cross-point hold attribute of a
snapshot
If you select "Key Disable" above, this also applies key
disable to the cross-point hold attribute.
If you select "Key Disable With Status," the key disable
function is applied, including the key on/off status.
Setting values
1 to 5
Notes
This setting is only reflected in the operation of the [XPT
HOLD] button when the [XPT HOLD] button operating
mode is set to "All Bus." (See page 520.) Note that the
snapshot cross-point hold attribute is also valid for settings
other than "All Bus."
Setting the operation mode when the
pattern limit is released
In the <Pattern Limit Transition> group of the Switcher
>Key/Wipe/FM/CCR menu, select either of the following
operation modes.
Auto: When the pattern limit is released, the remainder of
the transition is carried out automatically at a special-
purpose transition rate.
Manual: After the pattern limit is released, the transition
waits for the next operation, then executes. Until you
move the fader lever or press [AUTO TRANS], the
transition is not executed.
Setting the default wipe edge softness
1
In the Switcher >Key/Wipe/FM/CCR menu, press
[Wipe Edge Default], turning it on.
2
Set the following parameter.
Knob Parameter Adjustment
3
Settings Relating to Keys, Wipes, Frame Memory and Color Correction (Key/Wipe/FM/CCR Menu)
Soft Default value of
wipe edge
softness
Setting values
–
50.00 to
+50.00
539