Table of Contents
Advertisement
DME Wipe Pattern Variation and
Modifiers
You can apply the following changes and modifiers to the
selected DME wipe pattern in the same way as for an
ordinary wipe pattern.
For details about the method of operation, see "Setting
DME Wipe Modifiers" (page 149) and "Setting
Independent Key Transition DME Wipe Modifiers"
(page 153).
Direction: You can set the DME wipe direction to normal,
reverse, or alternating normal/reverse (see page 149).
However, this can be specified for a key transition only
when the following patterns are selected.
• 1204, 1207, 1221 to 1224, 7204, 7207, 7221 to 7224
Note
When pattern numbers 1201, 1202, 1203, 1205, 1206,
1208, 1251, 1701, and 1702 are selected, Direction
cannot be used.
Edge: You can apply a border or soft border (see
page 150).
In the case of user programmable DME patterns for
keys in which an edge has already been applied to the
effect, the behavior is as follows.
• When the DME wipe edge is enabled, only part of
the edge applied in the effect is enabled, and that
portion can be adjusted.
• When the DME wipe edge setting is disabled, the
edge applied in the effect is applied as-is.
Note
When pattern numbers 1011, 1012, 1013, 1701, and
1702 are selected, Edge cannot be used.
Positioner: You can move the DME wipe pattern or center
of the effect to an arbitrary position (see page 150).
Using the position select function, you can also
instantaneously move the pattern (see page 150).
This can only be used when one of the following
pattern numbers is selected.
• 1031, 7031
As the transition progresses, the pattern center
automatically moves initially from the set position
toward the center of the screen. In other words, the
effect obtained is the same as in a normal wipe with
the positioner set to [Auto Center].
• 1201 to 1208, 1221 to 1224, 1251, 7201 to 7208,
7221 to 7224
You can set the pattern position when the first
transition completes.
• 1381, 1391, 1393, 1394, 1396
You can set the center of the transition effect.
• 2651, 2652
You can move the pattern for each channel, or for
two channels simultaneously depending on the
relative values from the current positions (see
page 150).
• 2801 to 2804, 2811 to 2814
You can set the vertical position as the brick slides
in.
• 2851 to 2854, 2861 to 2864
You can set the pattern position for each channel
setting when the first transition completes.
Pattern limit: You can restrict the range of the transition
execution as desired. However, this is not available for
an independent key DME wipe.
For details, see "Pattern Limit" (page 86).
Size: You can set the size of the image. This can only be
used when one of the following pattern numbers is
selected.
• 1201 to 1208, 1221 to 1224, 1251, 2651, 2652, 2851
to 2854, 2861 to 2864, 7201 to 7208, 7221 to 7224
Crop: You can crop the image. It is also possible in 16:9
mode to crop both sides and convert the image to a 4:3
aspect ratio.
For the execution of the transition, you can select from
the following three options.
• Cut
• Last 5%
• Linear
When [Last 5%] is selected, you can set the [Release
Transition] as follows.
• Last 30%
• Last 5%
• Off
Note
When pattern numbers 1701 and 1702 are selected,
crop cannot be used.
DME Wipe Restrictions
Relation to common wipes
• DME wipes do not use the wipe generator built into the
switcher. Therefore, during the execution of a DME
wipe, you can still use a pattern produced by the wipe
generator as the source for a pattern key or mask.
• A DME wipe pattern cannot be used as the source for a
pattern key or mask.
147
Advertisement
Table of Contents
