HEIDENHAIN TNC 320 User Manual page 666

Index
Index
3
3-D basic rotation..................... 519
3-D touch probe
Calibrating.............................. 509
Using...................................... 501
3-D view................................... 546
A
About this manual........................ 6
Accessing tables...................... 349
Accessories................................ 99
Actual position capture............. 123
Adding comments............ 159, 160
Additional axes......................... 113
Additional axes for rotary axes. 469
Adjusting spindle speed........... 490
Align tool axis........................... 468
Angle functions........................ 322
Approach contour..................... 230
ASCII files................................ 427
Automatic program start.......... 574
Automatic tool measurement... 191
B
Backup....................................... 97
Basic rotation........................... 517
Measuring in Manual Operation
mode...................................... 517
Behavior after receipt of ETX.... 592
Block........................................ 125
Delete.................................... 125
Block check character............... 591
Block scan
In a point table....................... 573
C
CAD Viewer.............................. 277
CAD viewer and DXF converter
screen layout............................ 276
Calculating with parentheses... 360
Calculation of circles................ 323
Calculator................................. 163
Calling tool management......... 213
Cartesian coordinates
Circular path around circle center
CC.......................................... 245
Straight line............................ 241
Chamfer................................... 242
Circle........................ 246, 248, 254
Circle center............................. 244
Circular path............................. 254
around circle center CC.......... 245
Code number........................... 588
Comparison.............................. 636
Compensating workpiece
misalignment
666
By measuring two points on a
straight surface...................... 516
Condition of RTS line............... 591
Connector pin layout for data
interfaces................................. 623
Context-sensitive help.............. 177
Control panel.............................. 76
Coordinate transformation........ 424
Copying program sections 127, 127
D
Data backup....................... 97, 131
Data interface........................... 589
Connector pin layouts............ 623
Set up.................................... 589
Data output on the screen....... 337
Data transfer
File system............................. 591
Software................................. 593
Data transmission
Behavior after receipt of ETX.. 592
Block check character............. 591
Condition of RTS line............. 591
Data bits................................ 590
Handshake............................. 591
Parity...................................... 590
Protocol.................................. 590
Software TNC server.............. 592
Stop bits................................. 590
Datum shift
Resetting................................ 426
Via the datum table................ 425
Datum table
Transferring probed values..... 507
Defining local Q parameters..... 317
Defining nonvolatile Q parameters..
317
Defining the workpiece blank... 120
Depart contour......................... 230
Dialog....................................... 121
Directory.......................... 132, 137
Copy....................................... 140
Create.................................... 137
Delete.................................... 141
Displaying HTML files.............. 147
Displaying Internet files............ 147
Display of the NC program....... 160
Display screen............................ 75
DNC......................................... 602
Information from NC program 348
Downloading help files............. 181
Dwell time................ 439, 440, 441
DXF converter.......................... 278
Selecting hole positions
Icon.................................. 291
Mouse area...................... 290
Setting a datum...................... 283
HEIDENHAIN | TNC 320 | Conversational Programming User's Manual | 9/2016
E
Enter spindle speed................. 201
Error message.......................... 172
Help with............................... 172
Ethernet interface.................... 595
Configuring............................. 595
Connecting and disconnecting
network drives....................... 154
Connection possibility............ 595
Introduction............................ 595
External access........................ 581
External data transfer............... 153
F
FCL........................................... 588
FCL function................................ 9
Feature Content Level.................. 9
Feed rate.................................. 489
Adjust..................................... 490
Input options.......................... 122
On rotary axes, M116............. 469
Feed rate factor for plunging
movements M103.................... 396
Feed rate in millimeters per spindle
revolution M136....................... 397
File
create..................................... 137
Sort........................................ 143
tag.......................................... 142
File functions............................ 423
File management............. 129, 132
external data transfer............. 153
File Manager
Calling.................................... 134
File manager
Copying files.......................... 137
Copying tables....................... 139
Delete file.............................. 141
Directories
Copy................................. 140
Create.............................. 137
Directory................................ 132
File type................................. 129
File type
External file types............ 131
Function overview.................. 133
Overwriting files..................... 138
Protect file.............................. 143
Rename file............................ 142
Selecting files......................... 135
File status................................ 134
Filter for hole positions with DXF
data update.............................. 292
Firewall..................................... 601
FK programming...................... 259
Circular paths......................... 264
End point................................ 265
Fundamentals......................... 259