Data Cabling; Data In And Data Out Connectors; Daisy Chaining Fixtures - High End Systems studio spot User Manual

Data Cabling

You may connect up to 21 uniquely addressed fixtures per DMX link or up
to 32 fixtures for synchronized playback of the internal presets. To
connect the data cables, complete the following procedure:
1. Connect the data cable from the controller to the
located on the side of the first fixture. Refer to Figure 1.9.
Note: if you are cabling for synchronized preset playback, do not connect a
controller unless you intend to capture DMX data.
2. Daisy chain additional fixtures by connecting cables from the
connector to the
Figure 1.10.
to additional
DATA OUT
fixtures
WARNING : DO NOT MOUNT ON A NORMALLY
FLAMMABLE SURFACE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
ATTENTION: IMPROPRE A L'USAGE DOMESTIQUE.
CAUTION: MAINTAIN 1M SEPARATIO N BETWEEN EMPLACEMENTS SECS.
FIXTURE AND FLAMMABLE MATERIALS. SURFACE
TEMPERATURE MAY REACH 20 0° C ( t =40°C). NOT FOR RESIDENTIAL USE. SUITABLE FOR DRY
LOCATIONS ONLY . FOR SAFE INSTALLATION AND
OPERATION, CONSULT USER MANUAL.
POWER
terminate last
fixture
3. Install a terminator in the
DMX link.
Caution: failure to terminate the last fixture on each link can result in erratic
operation.
Note: if you are not using a controller to capture data for synchronized playback,
it is recommended that you install terminators on the first fixture's
connector and the last fixture's
DATA OUT
DANGER: INTENSE HEAT.
WARNING: DO NOT MOUNT ON A NORMALLY
FLAMMABLE SURFACE. NO USER
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION: IMPROPRE A L'USAGE
DOMESTIQUE. EMPLACEMENTS SECS.
CAUTION: MAINTAIN 1M SEPARATION
BETWEEN FIXTURE AND FLAMMABLE
MATERIALS. SURFACE TEMPERATURE MAY
REACH 200° C (t =40°C). NOT FOR
POWER
RESIDENTIAL USE. SUITABLE FOR DRY
Figure 1.9 Data In and Data Out Connectors
connectors on subsequent fixtures. Refer to
DATA IN
DATA IN DATA OUT DATA IN
WARNING: DO NOT MOUNT ON A NORMALLY
PARTS INSIDE. REFER SERVICING TO Q UALIFIED FLAMMABLE SURFACE. NO USER SERVICEABLE
SERVICE PERSONNEL.
ATTENTION: IMPROPRE A L'USAGE DOMESTIQUE.
EMPLACEMENTS SECS. CAUTION: MAINTAIN 1M SEPARATION BETWEEN
FIXTURE AND FLAMMABLE MATERIALS. SURFACE
a FOR RESIDENTIAL USE. SUITABLE FOR DRY TEMPERATURE MAY REACH 200° C (t =4 0°C) . NOT a
LOCATIONS ONLY. FOR SAFE INSTALLATION AND
OPERATION, CONSULT USER MANUAL.
POWER
Figure 1.10 Daisy Chaining Fixtures
DATA OUT
DATA OUT
DATA IN
DATA IN
DATA OUT DATA IN
a
DATA OUT DATA IN
WARNING : DO NOT MOUNT ON A NORMALLY
PARTS INSIDE. REFER SERVICING TO Q UALIFIED FLAMMABLE SURFACE. NO USER SERVICEABLE
SERVICE PERSONNEL.
ATTENTION: IMPROPRE A L'USAGE DOMESTIQUE.
EMPLACEMENTS SECS. CAUTION: MAINTAIN 1M SEPARATIO N BETWEEN
FIXTURE AND FLAMMABLE MATERIALS. SURFACE
FOR RESIDENTIAL USE. SUITABLE FOR DRY TEMPERATURE MAY REACH 200° C (t =40°C) . NOT a
LOCATIONS ONLY . FOR SAFE INSTALLATION AND
OPERATION, CONSULT USER MANUAL.
POWER
connector of the last fixture on each
connector.
Chapter 1 Installation and Setup
connector
DATA OUT
FC C Rul e s. O per ation is sub j ect to th e Thi s de vi ce com pl ie s wi th pa rt 15 o f the
fol low in g two co nd ition s: (1 ) Th i s de vi ce
(2) th is de vice mu st acce pt a ny in te rfe r- ma y no t caus e ha rm fu l i nte rfer en ce s, an d
e nce th at may cau se u nde sir ed o pe ra ti o n.
Co nfor ms to ETL L i sted
UL Std 195 0
® Ce rtifie d to CAN /C SA C 22 .2 N o. 9 50 c ®
675 01
DMX controller
DATA IN
1-9