Connecting And Addressing Fixtures For Synchronized Playback; Data In And Data Out Connectors; Daisy Chaining Fixtures - High End Systems studio spot User Manual

Connecting and Addressing Fixtures for Synchronized Playback

To connect and address fixtures for synchronized playback, complete the
following procedure:
1. Connect a data cable from the master fixture's
the first slave's
2. Daisy chain slave fixtures by connecting cables from the
connector to the
Figure 4.4.
to additional
fixtures
terminate
last fixture
3. Install terminators on both ends of the link. Refer to Figure 4.4.
4. Power on all fixtures.
5. Press and hold <
system (if necessary).
6. Press <
7. Using the up and down arrow keys, set the master's DMX starting
channel to C 0 0 1 or to fixture F 0 1 (depending on which address
mode you are in).
8. Set the slave fixtures' starting channels/fixture numbers to any
address other than C 0 0 1 or F 0 1 .
4-10 Studio Spot User's Manual
connector. Refer to Figure 4.3.
DATA IN
DATA OUT
Figure 4.3. Data In and Data Out Connectors
connector on subsequent fixtures. Refer to
DATA IN
slave fixture
DATA OUT DATA IN
WA RNING : DO NOT MOUN T ON A NORMALLY
FLAMMABLE SURFACE. NO USER SERVIC EABLE
PARTS IN SIDE. REFER SERVIC ING T O QUA LIFIED
SERVICE PERSONNEL. ATTENTION: IMPROPRE A L'USAGE DOMESTIQUE.
EMPLACEMENTS SECS.
CAUTION: MAINTAIN 1M SEPARATIO N BET WEEN
FIXTURE AND FLAMMABL E MATERIALS. SURFA CE
TEMPERATUR E MAY REACH 200° C ( t =40°C). NOT
FOR RESIDENTIAL U SE. SUITA BLE FOR D RY a
LOC ATIONS O NLY . FOR SAFE INSTAL LATION AND
OPERAT ION, C ONSU LT U SER MANU AL.
POWER
Figure 4.4. Daisy Chaining Fixtures
> until the each fixture unlocks the menu
MENU
> to address the fixture.
ENTER
DATA OUT
DATA IN
DATA OUT
DATA IN
DANGER: INTENSE HEAT.
WARNING: DO NOT MOUNT ON A NORMALLY
FLAMMABLE SURFACE. NO USER
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION: IMPROPRE A L'USAGE
DOMESTIQUE. EMPLACEMENTS SECS.
CAUTION: MAINTAIN 1M SEPARATION
BETWEEN FIXTURE AND FLAMMABLE
MATERIALS. SURFACE TEMPERATURE MAY
REACH 200° C (t =40°C). NOT FOR
POWER
RESIDENTIAL USE. SUITABLE FOR DRY a
slave fixture
DATA OUT DATA IN
WARNING: DO NOT MOUNT ON A N ORMALLY
FLAMMABLE SURFACE. NO U SER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO Q UALIFIED
ATTEN TION: IMPROPRE A L'USAGE DOMESTIQU E. SERVIC E PERSON NEL.
EMPLACEMENTS SECS.
C AUTION: MAINTA IN 1M SEPARAT ION BETWEEN
FIXTUR E AND FLA MMA BLE MATER IALS. SURFACE
TEMPERATURE MAY REACH 200° C (t =40°C). NOT
FOR RESIDENTIAL USE. SUITABLE FOR DRY a
LOCATIONS ONLY. FOR SAFE INSTALLATION AND
OPERATION, CONSULT USER MANUAL.
POWER
connector to
DATA OUT
master fixture
install
DATA OUT DATA IN
terminator
WARNING : DO N OT MOUNT ON A NORMALLY
FLAMMAB LE SU RFAC E. NO USER SERVICEABLE
PART S INSIDE. REFER SER VICING TO QUALIFIED
ATTENTION: IMPROPRE A L 'USAGE DOMESTIQUE. SERVICE PERSONNEL.
EMPLACEMENTS SECS.
CAU TION: MAINTAIN 1M SEPARATION BETWEEN
FIXT URE A ND FLAMMABLE MATERIAL S. SU RFACE
TEMPERATURE MAY REAC H 200° C (t =40°C). NOT
FOR RESID ENT IAL USE. SU ITABLE FOR DRY a
LOC ATION S ONLY . FO R SA FE INSTALLATION AND
OPERATION, CONSULT USER MA NUAL.
POWER