Dürkopp Adler 867-M PREMIUM Service Instructions Manual page 5

Table of Contents
19.2.3 Disassembling the encoder ...................................................... 93
19.2.4 Disassembling the stator .......................................................... 94
19.2.5 Disassembling the rotor ............................................................ 94
19.3
19.3.1 Assembling the rotor................................................................. 95
19.3.2 Assembling the stator ............................................................... 96
19.3.3 Assembling the encoder ........................................................... 97
19.3.4 Assembling the cover ............................................................... 97
19.3.5 Locking the machine in place ................................................... 98
19.3.6 Assembling the handwheel flange ............................................ 98
19.3.7 Assembling the handwheel....................................................... 99
20
20.1
20.2
20.3
20.4
20.4.1 Setting the stitch length (Stitchlen.) parameter ................ 103
20.4.2 Setting the foot pressure (Foot Press.) parameter ............ 104
20.4.3 Setting the needle thread tension (Thr.Tens.) parameter... 104
20.4.4 Setting the sewing foot stroke (Foot Stroke) parameter .... 104
20.4.5 Setting the Start bartack parameter (Start Tack)............... 105
20.4.6 Set End bartack parameter (End Tack) ................................ 105
20.4.7 Setting the Thread cutter parameter (Thread Trim)............ 105
20.4.8 Setting the daily piece counter (DailyPieces) parameter ... 105
20.5
20.5.1 Setting the Thread cutter parameter (Thread Trim)............ 107
20.5.2 Setting the Thread clamp parameter (Thread Clamp) ......... 108
20.5.3 Setting the Speed (Speed) parameter.................................... 110
20.5.4 Setting the Stop positions (Stop Positions) parameter .... 110
20.5.5 Setting the Sewing foot (Foot) parameter ............................. 110
20.5.6 Setting the needle thread tension (Thr.Tens.) parameter... 111
20.5.7 Setting the sewing foot stroke (Stroke) parameter ............... 112
20.5.8 Setting the stitch length (Stitchlen.) parameter ................ 113
20.5.9 Setting the Bobbin (Bobbin) parameter................................. 113
20.5.10 Setting Motor holding force (Holding Force) parameter .... 114
20.5.11 Setting the Pedal (Pedal) parameter..................................... 114
20.5.12 Setting the Needle cooling (NeedleCooling) parameter ..... 115
20.5.13 Setting the Seam center guide (CenterGuide) parameter ... 115
20.5.14 Setting the Edge guide (EdgeGuide) parameter ................... 116
20.5.15 Setting the Material thickness detection
20.5.16 Setting the Correction of effects of high speed
20.5.17 Setting the light barrier (LightBarrier) parameter ............. 117
20.5.18 Setting the Segment length (Mode Seg.Size) parameter.... 118
20.5.19 Setting the Threading mode (Threading) parameter ........... 118
20.6
20.6.1 Setting the Language selection (Language) parameter ........ 119
20.6.2 Setting the Parameter view (ParameterView) parameter.... 119
20.6.3 Setting the Input configuration (Input Config) parameter . 120
Service Instructions 867-M PREMIUM - 03.0 - 05/2017
Assembling the drive ................................................................ 95
Programming ........................................................................ 101
Calling up the Technician level ............................................... 101
Structure of the software......................................................... 101
Parameter selection (ParameterCall) submenu............... 102
Program presettings (Default Program) submenu ........... 103
Machine configuration (Machine config.) submenu ......... 106
(Fabric Thickness) parameter ......................................... 116
(Speed Corr) parameter ...................................................... 117
User configuration (User config.) submenu...................... 118
3