D-Link xStack DGS-3620 Reference Manual page 578

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
(for example, 10.1.2.3/255.0.0.0 or in CIDR format, 10.1.2.3/8).
vlan - (Optional) The name of the VLAN corresponding to the IP interface.
<vlan_name 32> - Enter the VLAN name. The maximum length is 32 characters.
state - Enable or disable the IP interface.
enable - Enable the IP interface.
disable - Disable the IP interface.
proxy_arp - (Optional) Enable or disable the proxy ARP. This is for the IPv4 function. The default
is disabled.
enable - Enable the proxy ARP.
disable - Disable the proxy ARP.
local - (Optional) This setting controls whether the system provides the proxy reply for the ARP
packets destined for IP addresses located in the same interface as the received interface.
When proxy ARP is enabled for an interface, the system will do the proxy reply for the ARP
packets destined for IP addresses located on a different interface. For ARP packets destined
for IP address located on the same interface, the system will check this setting to determine
whether to reply. The default is disabled.
enable - Enable the local proxy ARP function.
disable - Disable the local proxy ARP function.
bootp - Allows the selection of the BOOTP protocol for the assignment of an IP address to the
switch's System IP interface.
dhcp - Allows the selection of the DHCP protocol for the assignment of an IP address to the
switch's System.
ipv6 - The following are IPv6-related parameters.
ipv6address - The IPv6 address and subnet prefix of the IPV6 address to be created.
prefix_name - Specifies the IPv6 prefix name.
<string 1-12> - Enter the IPv6 prefix name. This name can be up to 12 characters long.
<ipv6networkaddr> - The IPv6 address and subnet prefix of the IPV6 address to be
created.
state - Enable or disable the IPv6 state of the IP interface.
enable - Enable the IPv6 state of the IP interface.
disable - Disable the IPv6 state of the IP interface.
ip_mtu - Specifies the IP Layer MTU value used.
<value 512-16383> - Enter the IP Layer MTU value used here. The value must be between
512 and 16383. Note: This value is for hardware forwarding only.
ipv4 state - The state of the IPv4 interface.
enable - Enable the IPv4 state of the IP interface.
disable - Disable the IPv4 state of the IP interface.
dhcpv6_client - Specifies the DHCPv6 client state of the interface.
enable - Specifies that the DHCPv6 client state of the interface will be enabled.
disable - Specifies that the DHCPv6 client state of the interface will be disabled.
rapid_commit - (Optional) Specifies to allow the two-message exchange method for address
assignment.
ip_directed_broadcast - Specifies the IP directed-broadcast state of the interface.
enable - Specifies that the IP directed-broadcast state of the interface will be enabled.
disable - Specifies that the IP directed-broadcast state of the interface will be disabled.
dhcp_option12 - (Optional) Specifies to configure the DHCP Option 12 parameters.
hostname - Specifies the host name to be inserted in the DHCPDISCOVER and
DHCPREQUEST message.
<hostname 63> - Enter the host name here. This name must start and end with a letter or
a number. Only letters, digits, and hyphens are allowed as interior characters. This
name can be up to 63 characters long.
clear_hostname - Specifies to clear the host name setting. If a host name is empty, the
system name will be used to encode Option 12. The length of the system is more than 63
characters. The superfluous characters will be truncated. If the system name is also empty,
then the product model name will be used to encode Option 12.
state - Specifies to enable or disable the insertion of the Option 12 information in the
DHCPDISCOVER and DHCPREQUEST messages.
enable - Specifies to enable the insertion of the Option 12 information in the
DHCPDISCOVER and DHCPREQUEST messages.
disable - Specifies to disable the insertion of the Option 12 information in the
573