Chapter 68 Mld Snooping Commands - D-Link xStack DGS-3620 Reference Manual

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
Chapter 68
config mld_snooping [vlan_name <vlan_name 32> | vlanid <vlanid_list> | all] {state [enable |
disable] | topology_changes_notification [ignore | process] | fast_done [enable | disable] |
proxy_reporting {state [enable | disable]| source_ip <ipv6addr>}}(1)
config mld_snooping rate_limit [ports <portlist> | vlanid <vlanid_list>] [<value 1-1000> | no_limit]
show mld_snooping rate_limit [ports <portlist> | vlanid <vlanid_list>]
create mld_snooping static_group [vlan <vlan_name 32> | vlanid <vlanid_list>] <ipv6addr>
config mld_snooping static_group [vlan <vlan_name 32> | vlanid <vlanid_list>] <ipv6addr> [add
| delete] <portlist>
delete mld_snooping static_group [vlan <vlan_name 32> | vlanid <vlanid_list>] <ipv6addr>
show mld_snooping static_group {[vlan <vlan_name 32> | vlanid <vlanid_list>] <ipv6addr>}
show mld_snooping statistic counter [vlan <vlan_name 32> | vlanid <vlanid_list> | ports
<portlist>]
clear mld_snooping statistics counter
config mld_snooping querier [vlan_name <vlan_name 32> | vlanid <vlanid_list> | all]
{query_interval <sec 1-65535> | max_response_time <sec 1-25> | robustness_variable
<value 1-7> | last_listener_query_interval <sec 1-25> | state [enable | disable] | version
<value 1-2>}(1)
config mld_snooping mrouter_ports [vlan <vlan_name 32> | vlanid <vlanid_list>] [add | delete]
<portlist>
config mld_snooping mrouter_ports_forbidden [vlan <vlan_name 32> | vlanid <vlanid_list>]
[add | delete] <portlist>
enable mld_snooping
disable mld_snooping
show mld_snooping {[vlan <vlan_name 32> | vlanid <vlanid_list >]}
show mld_snooping group {[vlan <vlan_name 32> | vlanid <vlanid_list> | ports <portlist>]
{<ipv6addr>}}
show mld_snooping mrouter_ports [vlan <vlan_name 32> | vlanid <vlanid_list> | all] {[static |
dynamic | forbidden]}
show mld_snooping forwarding {[vlan <vlan_name 32> | vlanid <vlanid_list>]}
68-1 config mld_snooping
Description
This command is used to configure MLD snooping on the switch.
Format
config mld_snooping [vlan_name <vlan_name 32> | vlanid <vlanid_list> | all] {state [enable |
disable] | topology_changes_notification [ignore | process] | fast_done [enable | disable] |
proxy_reporting {state [enable | disable]| source_ip <ipv6addr>}}(1)
Parameters
vlan_name - Specifies the name of the VLAN for which MLD snooping is to be configured.
<vlan_name 32> - Enter the VLAN name. The maximum length is 32 characters.
vlanid - Specifies the VLAN ID list.
<vlanid_list> - Enter the VLAN ID list.
MLD Snooping
Commands
785