Omron CP1L Operation Manual page 677

Auxiliary Area Allocations by Address
Address Name
Words Bits
A393 A393.00 Serial Port 2
to PT Communi-
A393.07 cations Flags
(CP1L M-type
CPU Units)
Serial Port 1
PT Communi-
cations Flags
(CP1L L-type
CPU Units)
A393.08 Serial Port 2
to PT Priority
A393.15 Registered
Flags (CP1L
M-type CPU
Units)
Serial Port 1
PT Priority
Registered
Flags (CP1L
L-type CPU
Units)
A393.00 Serial Port 2
to Reception
A393.15 Counter (No-
protocol
Mode) (CP1L
M-type CPU
Units)
Serial Port 1
Reception
Counter (No-
protocol
Mode) (CP1L
L-type CPU
Units)
A394 A394.00 Serial Port 1
to PT Communi-
A394.07 cations Flags
(CP1L M-type
CPU Units)
A394.08 Serial Port 1
to PT Priority
A394.15 Registered
Flags (CP1L
M-type CPU
Units)
A394.00 Serial Port 1
to Reception
A394.15 Counter (No-
protocol
Mode) (CP1L
L-type CPU
Units)
A395 A395.12 DIP Switch
Pin 6 Status
Flag
Function
The corresponding bit will be ON
when the serial port 2 of a CP1L M-
type CPU Unit is communicating with
a PT in NT Link or Serial PLC Link
mode.
Bits 0 to 7 correspond to units 0 to 7.
The corresponding bit will be ON
when the serial port 1 of a CP1L L-
type CPU Unit is communicating with
a PT in NT Link or Serial PLC Link
mode.
Bits 0 to 7 correspond to units 0 to 7.
The corresponding bit will be ON for
the PT that has priority when the
serial port 2 of a CP1L M-type CPU
Unit is communicating in NT link
mode.
Bits 0 to 7 correspond to units 0 to 7.
These flags are written when the pri-
ority registration command is
received.
The corresponding bit will be ON for
the PT that has priority when the
serial port 1 of a CP1L L-type CPU
Unit is communicating in NT link
mode.
Bits 0 to 7 correspond to units 0 to 7.
These flags are written when the pri-
ority registration command is
received.
Indicates (in binary) the number of
bytes of data received when the
serial port 2 of a CP1L M-type CPU
Unit is in no-protocol mode.
Indicates (in binary) the number of
bytes of data received when the
serial port 1 of a CP1L L-type CPU
Unit is in no-protocol mode.
The corresponding bit will be ON
when the serial port 1 of a CP1L M-
type CPU Unit is communicating with
a PT in NT link mode.
Bits 0 to 7 correspond to units 0 to 7.
The corresponding bit will be ON for
the PT that has priority when the
serial port 1 of a CP1L M-type CPU
Unit is communicating in NT link
mode.
Bits 0 to 7 correspond to units 0 to 7.
Indicates (in binary) the number of
bytes of data received when serial
port 1 of a CP1L L-type CPU Unit is
in no-protocol mode.
The status of pin 6 on the DIP switch
on the front of the CPU Unit is written
to this flag every cycle.
Settings Status
after
mode
change
ON: Commu- Retained Cleared
nicating
OFF: Not
communicat-
ing
ON: Priority Retained Cleared
registered
OFF: Priority
not registered
--- Retained Cleared
ON: Commu- Retained Cleared
nicating
OFF: Not
communicat-
ing
ON: Priority Retained Cleared
registered
OFF: Priority
not registered
--- Retained Cleared
ON: Pin 6 ON Retained See
OFF: Pin 6
OFF
Appendix D
Status Write Related
at star- timing flags, set-
tup tings
Refreshed ---
when there
is a nor-
mal
response
to the
token.
See Func- ---
tion col-
umn.
Refreshed ---
when data
is received.
Refreshed ---
when there
is a nor-
mal
response
to the
token.
See Func- ---
tion col-
umn.
Refreshed ---
when data
is received.
Written ---
Func- every
tion col- cycle.
umn.
643