IBM System Storage TS3310 Setup And Operator Manual page 268

DR003 10-31
DR004 10-31
DR005 10-31
DR006 10-32
DR007 10-32
DR009 10-33
DR010 10-33
DR011 10-33
DR012 10-34
DR014 10-34
DR015 10-35
DR018 10-35
DR019 10-35
DR020 10-36
DR021 10-36
DR022 10-36
DR024 10-37
DR026 10-37
DR028 10-37
DR029 10-37
DR030 10-38
DR031 10-38
DR032 10-38
DR033 10-38
DR034 10-39
DR035 10-39
DR036 10-39
drive
add new 11-6
replace 11-10
Drive 1-6
channel calibration 1-9
control path failure 10-38
coordinates 1-13
determining SCSI and Fibre Channel
IDs 2-4
general diagnostic 10-32
LEDs 9-9
load failure 10-38
loss of communication 10-37
manually clean 10-35
power management 1-9
remove 11-9
sled not auto leveling 10-38
speed matching 1-9
unload diagnostic 10-31
drive dump 7-15
drive sled
description 1-8
remove/replace 11-6
drives 7-13
adding control path 7-14
capturing a dump 7-15
fibre channel IDs 2-4
IDs 7-14
loading 7-13
maximum number 1-2
modifying fibre settings 7-15
online/offline 7-14
SCSI IDs 2-4
unloading 7-14
viewing information 7-13
E
environment 1-16
operating 1-16
X-2
TS3310 Tape Library Setup and Operator Guide
environment (continued)
particulates 1-16
Error codes
Service Action Tickets 10-1
error messages
viewing 7-9
Error messages
operator intervention 9-2
errors
obtaining from library and
drives A-1
RS/6000 A-1
errpt command, using A-1
expansion module 1-3
connectivity diagnostic 10-33
F
feature licenses
capacity expansion 1-9
control path failover 1-9, 1-10
data path failover 1-9, 1-10
path failover 1-9, 1-10
features
optional 1-8
capacity expansion 1-9
drives 1-8
firmware update by IBM service
personnel 1-11
license keys 1-9
path failover 1-10
redundant power supply 1-9
Fibre Channel
drive IDs 2-4
supported topologies 2-6
Fibre Channel drive
compatibility with Multi-Path
Architecture 1-15
Fibre Channel interface 2-9
cables and speeds 2-9
connectors and adapters 2-11
LUN assignments 2-7
persistent binding 2-10
sharing on a SAN 2-11
World Wide names 2-7
zoning 2-10
firmware
upgrades 7-10
Firmware
drive 7-11
FMR tape 7-12
creating 7-12
library 7-10
updating
using Fibre Channel
interface 7-13
using ITDT Tool 7-11
using SCSI interface 7-13
foot pads
remove 11-19
replace 11-19
front panel
access door 1-3
control module 1-3
expansion module 1-3
I/O Station 1-3
Operator Panel 1-4
front panel (continued)
power button 1-4
G
gear rack alignment 11-19
glossary F-1
H
height of tape library 1-15
host
sharing library 1-15
hp-ux system error information A-9
I
I/O slots
assign 7-4
assigning 6-5
I/O Station 1-3
close door 10-37
lock diagnostic 10-33
locking/unlocking 7-10
I/O Station slots
maximum number 1-2
IBM Ultrium Tape Drive 1-8
install planning 2-1
installation 3-1
cabling a 14U library with fibre
drives 3-19
cabling a 14U library with SCSI
drives 3-20
cabling a 5U library with fibre and
SCSI drives 3-21
cabling a 5U library with fibre
drives 3-17
cabling a 5U library with SCSI
drives 3-17
cabling the library 3-16
configuring the library 3-23
identifying location 3-6
installing a drive 3-14
installing a power supply 3-15
installing components removed for
weight reduction 3-14
placing the library 3-12
planning 2-1
powering on the library 3-22
rack 3-4, 3-5, 3-6, 3-8, 3-11, 3-12, 3-13,
3-14, 3-15
rack ears 3-13
rails 3-8
reducing library weight 3-11
removing drive 3-12
removing power supply 3-11
test library 3-2
unpacking shipment 3-1
verifying kit contents 3-5
verifying shipment 3-1
interfaces, supported 1-8
interior components 1-6
picker assembly 1-7
robotic system 1-7
Storage column 1-7
inventory library 10-36