D-Link xStack DGS-3426 Cli Manual page 178

xStack DGS-3400 Series Layer 2 Gigabit Managed Switch CLI Manual
DGS-3400:4#config time_zone operator + hour 2 min 30
Command: config time_zone operator + hour 2 min 30
Success.
DGS-3400:4#
config dst
Purpose Used to enable and configure time adjustments to allow for the use of Daylight
Savings Time (DST).
Syntax config dst [disable | repeating {s_week <start_week 1-4,last> | s_day <start_day
sun-sat> | s_mth <start_mth 1-12> | s_time start_time hh:mm> | e_week
<end_week 1-4,last> | e_day <end_day sun-sat> | e_mth <end_mth 1-12> | e_time
<end_time hh:mm> | offset [30 | 60 | 90 | 120]} | annual {s_date start_date 1-31> |
s_mth <start_mth 1-12> | s_time <start_time hh:mm> | e_date <end_date 1-31> |
e_mth <end_mth 1-12> | e_time <end_time hh:mm> | offset [30 | 60 | 90 | 120]}]
Description DST can be enabled and configured using this command. When enabled this will
adjust the system clock to comply with any DST requirement. DST adjustment effects
system time for both manually configured time and time set using SNTP service.
disable - Disable the DST seasonal time adjustment for the Switch.
repeating - Using repeating mode will enable DST seasonal time adjustment.
Repeating mode requires that the DST beginning and ending date be specified using a
formula. For example, specify to begin DST on Saturday during the second week of
April and end DST on Sunday during the last week of October.
annual - Using annual mode will enable DST seasonal time adjustment. Annual mode
requires that the DST beginning and ending date be specified concisely. For example,
specify to begin DST on April 3 and end DST on October 14.
s_week - Configure the week of the month in which DST begins.
•
e_week - Configure the week of the month in which DST ends.
•
s_day – Configure the day of the week in which DST begins.
•
e_day - Configure the day of the week in which DST ends.
•
s_mth - Configure the month in which DST begins.
•
e_mth - Configure the month in which DST ends.
•
s_time – Configure the time of day to begin DST.
•
e_time - Configure the time of day to end DST.
•
s_date - Configure the specific date (day of the month) to begin DST.
• <start_date 1-31> - The start date is expressed numerically.
<start_week 1-4,last> - The number of the week during the month in which
DST begins where 1 is the first week, 2 is the second week and so on, last is
the last week of the month.
<end_week 1-4,last> - The number of the week during the month in which
DST ends where 1 is the first week, 2 is the second week and so on, last is
the last week of the month.
<start_day sun-sat> - The day of the week in which DST begins expressed
using a three character abbreviation (sun, mon, tue, wed, thu, fri, sat)
<end_day sun-sat> - The day of the week in which DST ends expressed
using a three character abbreviation (sun, mon, tue, wed, thu, fri, sat)
<start_mth 1-12> - The month to begin DST expressed as a number.
<end_mth 1-12> - The month to end DST expressed as a number.
<start_time hh:mm> - Time is expressed using a 24-hour clock, in hours and
minutes.
<end_time hh:mm> - Time is expressed using a 24-hour clock, in hours and
minutes.
175