Jc_Rxb_Output_Clk_Div_Control; Jc_Charge_Pump_ Control; Charge Pump Control Setting (Cp_Ctrl) - Texas Instruments TLK3134 Data Manual

4-channel multi-rate transceiver
Hide thumbs Also See for TLK3134:
Table of Contents

Advertisement

TLK3134
SLLS838F – MAY 2007 – REVISED DECEMBER 2009
ADDRESS: 0x9104
BIT(s)
NAME
4/5.37124.6:0
FB_DIV[6:0]
ADDRESS: 0x9105
BIT(s)
NAME
4/5.37125.14:8
RXB_DIV[6:0]
4/5.37125.7
OUTDIV_EN
4/5.37125.6:0
RXTX_DIV[6:0]
ADDRESS: 0x9106
BIT(s)
NAME
4/5.37126.15:14 CP_BUF_CTRL[1:0]
4/5.37126.13:0
CP_CTRL[13:0]
(1) When JC PLL is used, this register value should be set according to the values specified in Charge Pump Control Setting Table
(4/5.37124[6:0]) (IN DECIMAL)
80
Detailed Description
Table 2-121. JC_REFCLK_FB_DIV_CONTROL (continued)
Controls the feedback divider value
See
Figure
1-3, and Appendix A for provisioning details.
Note: JC_CHARGE_PUMP_ CONTROL (4/5.37126) needs to be set
accordingly based on FB_DIV range. Refer
Control Setting (CP_CTRL)
Table 2-122. JC_RXB_OUTPUT_CLK_DIV_CONTROL
Receive Byte Clock Output Divider Value. This divider value is always
provisioned with the same value as RXTX_DIV[6:0]. See
Appendix A for provisioning details. This value is only used when the jitter
cleaner is used to source the receive parallel interface output clock. Legal
programmed values are greater than or equal to 6
1 = Enables output divider (RXTX_DIV)
0 = Disables output divider
RX/TX SERDES Output Divider Value
See
Figure
1-3, and Appendix A for provisioning details Legal
programmed values are greater than or equal to 6
Table 2-123. JC_CHARGE_PUMP_ CONTROL
Charge pump buffer control
Charge pump control. When JC PLL is used, CP_CTRL[13:0] values
need to be set according to FB_DIV[6:0] range. Refer

Charge Pump Control Setting (CP_CTRL)

Table 2-124. Charge Pump Control Setting (CP_CTRL)
FB DIV VALUE RANGE
1 - 15
16 - 18
19 - 30
31 - 33
34 - 45
46 - 53
54 - 59
60 - 68
69 - 77
78 - 85
86 - 88
89 - 91
92 - 99
100 - 107
108 - 113
114 - 127
Submit Documentation Feedback
Product Folder Link(s):
DEFAULT: 0x018E
DESCRIPTION
Table
2-124: Charge Pump
DEFAULT: 0x0E8E
DESCRIPTION
Figure
(1)
DEFAULT: 0x00C0
DESCRIPTION
Table
JC_CHARGE_PUMP_ CONTROL SETTING
(4/5. 37126 [15:0])
0x00FF
0x00C1
0x0081
0x017F
0x017D
0x011F
0x0151
0x0121
0x01C3
0x0101
0x02FB
0x0183
0x0237
0x0181
0x0261
0x0215
Copyright © 2007–2009, Texas Instruments Incorporated
TLK3134
www.ti.com
ACCESS
RW
ACCESS
1-3, and
RW
RW
RW
ACCESS
RW
2-124:

Advertisement

Table of Contents
loading

Table of Contents