Summary of Contents for Texas Instruments TLK3134 XAUI
Page 1
User’s Guide Rev 0.1 September 2007 TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide ABSTRACT This User’s Guide describes the usage and construction of the TLK3134 evaluation module (EVM). This document provides guidance on proper use by showing some device configurations and test modes.
Voltage Monitoring LED circuits provide quick indication that the voltage is within specification. The MDIO register map is located within the TLK3134 XAUI Transceiver/4 Channel Multi-Rate Transceiver datasheet. TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide...
EVM kit, the 2.5V setting should be selected on the VDDM Power Select Header (JMP43). Figure 2. TLK3134 EVM VDDM Voltage Source Selection JMP43 1P2V 2.5V SELECTED AS VDDM VDDM SUPPLY VOLTAGE 2P5V TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
Place the jumper position to either the “UP 5%”, “DN 5%”, or “NOM” positions keeping the center pin in common as demonstrated in the following figure. Figure 4. TLK3134 EVM Regulator Margin Selection TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
Page 8
1.2V Banana Jack. A dedicated LDO 1.2V Regulator powering the Jitter Cleaner Power Plane should be considered for the end application. TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
LED drive circuit to the output of the Voltage Monitor circuit causing the LED to be lit only when the voltage is within the acceptable range. TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
GND which is less than the acceptable plane voltage. Figure 7. TLK3134 EVM Voltage Monitor LED Connected Directly to Plane Example TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
Page 11
LED drive circuit is connected directly to the power plane itself. TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
PULLUP_EN PRTAD2 PRTAD3 GPO[4:0] LEDS PRTAD4 JMP24 THE PINS ON THIS SIDE OF ALL HEADER BLOCKS ARE GND GPO0 GPO1 GPO2 GPO3 GPO4 TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
Page 13
GPO0: Contains the Channel 0 PRBS currently passing (when low) indication. An external loopback connection (via external cables) is required during PRBS testing. TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
Page 14
When ENABLE is high the device operates normally. A hard or soft reset much be applied after a change of state occurs on this input signal. TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
Page 15
Channel 2 responds to port address 2 within the block of four port addresses. Channel 3 responds to port address 3 within the block of four port addresses. TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
The bi-directional MDIO pin is pulled up to 1.2V or 2.5V (VDDM) with a 1.5k Ω resistor as per the MDIO Standard. Figure 9. TLK3134 EVM MDIO Connector (JMP22) MDIO JMP22 TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
NOTE: TRST_N should be tied low when the JTAG port is not in use and during normal operation of the port as shown in the following figure. Figure 10. TLK3134 EVM JTAG Connector (JMP23) TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
TLK3134 to be reset and reinitialized If switch SW1 is pressed, the device RESET pin (RST_N) goes LOW, the entire TLK3134 device is reinitialized. TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
RXCLK_1 are used. During Parallel Loopback, the clocks can be jumpered together as shown in the following diagram. Figure 15. Parallel Loop Back with Static Data Pattern Example TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
50 ohm Impedance. Always consult with your board manufacturer for their process/design requirements to ensure the desired impedance is achieved. TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
Revision History Rev 0.1: Updated the Schematic Figures, BOM and Power Supply Section regarding the Updated Jitter Cleaner Loop Filter Circuit. (09/17/07 JN) TLK3134 XAUI Transceiver / 4 Channel Multi-Rate Transceiver Evaluation Module (EVM) Users’ Guide SLLU104A - September 2007...
Page 58
Any exceptions to this are strictly prohibited and unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory authorities, which is responsibility of user including its acceptable authorization.
Page 59
FCC Interference Statement for Class B EVM devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 60
Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan. Texas Instruments Japan Limited (address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan http://www.tij.co.jp...
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue.