NETGEAR SRX5308 - ProSafe® Quad WAN Gigabit SSL VPN Firewall Reference Manual page 350

ProSafe Gigabit Quad WAN SSL VPN Firewall SRX5308 Reference Manual
Table C-18. System Logs: IPsec VPN Tunnel, SA lifetime (150 sec in phase 1; 300 sec in
phase 2), VPN Tunnel Not Reestablished
Message
Explanation
Recommended Action None
Table C-19. System Logs: IPsec VPN Tunnel, Dead Peer Detection and Keepalive (Default
30 sec)
Messages 1 through 4
Message 5
Message 7
Explanation
Recommended Action None
C-12
2000 Jan 1 04:52:33 [SRX5308] [IKE] Using IPsec SA configuration: 192.168.11.0/
24<->192.168.10.0/24_
2000 Jan 1 04:52:33 [SRX5308] [IKE] Configuration found for 20.0.0.1._
2000 Jan 1 04:52:59 [SRX5308] [IKE] Phase 1 negotiation failed due to time up for
20.0.0.1[500]. b73efd188399b7f2:0000000000000000_
2000 Jan 1 04:53:04 [SRX5308] [IKE] Phase 2 negotiation failed due to time up
waiting for phase 1. ESP 20.0.0.1->20.0.0.2 _
2000 Jan 1 04:53:05 [SRX5308] [IKE] Using IPsec SA configuration: 192.168.11.0/
24<->192.168.10.0/24_
2000 Jan 1 04:53:05 [SRX5308] [IKE] Configuration found for 20.0.0.1._
2000 Jan 1 04:53:05 [SRX5308] [IKE] Initiating new phase 1 negotiation:
20.0.0.2[500]<=>20.0.0.1[500]_
2000 Jan 1 04:53:05 [SRX5308] [IKE] Beginning Identity Protection mode._
2000 Jan 1 04:53:05 [SRX5308] [IKE] Setting DPD Vendor ID_
2000 Jan 1 04:53:36 [SRX5308] [IKE] Phase 2 negotiation failed due to time up
waiting for phase 1. ESP 20.0.0.1->20.0.0.2 _
Phase 1 and phase 2 negotiations failed because of a mismatch of the WAN IP
address in the IPsec VPN policy and the WAN IP address of the remote host
attempting to establish the IPsec VPN tunnel.
2000 Jan 1 04:13:39 [SRX5308] [IKE] Received request for new phase 1
negotiation: 20.0.0.2[500]<=>20.0.0.1[500]_
2000 Jan 1 04:13:39 [SRX5308] [IKE] Beginning Identity Protection mode._
2000 Jan 1 04:13:39 [SRX5308] [IKE] Received Vendor ID: RFC XXXX_
2000 Jan 1 04:13:39 [SRX5308] [IKE] Received Vendor ID: DPD_
2000 Jan 1 04:13:39 [SRX5308] [IKE] DPD is Enabled_
2000 Jan 1 04:13:39 [SRX5308] [IKE] For 20.0.0.1[500], Selected NAT-T version:
RFC XXXX_
2000 Jan 1 04:13:39 [SRX5308] [IKE] Setting DPD Vendor ID_
Message 1–4: After receiving a request for phase 1 negotiation, a Dead Peer
Detection Vendor ID is received.
Message 5: DPD is enabled.
Message 7: The DPD vendor ID is set.
v1.0, April 2010
System Logs and Error Messages