Table of Contents
Advertisement
M-series and MX-series Devices
434
Table 245: Control Association Configuration Details
Task
Specify the method and
reason that the virtual BGF
includes in Registration
Request ServiceChange
commands when it attempts
to reregister with the
gateway controller or
register with a new gateway
controller after the control
association is disconnected.
Specify the method and
reason that the virtual BGF
includes in Unregistration
Messages in ServiceChange
commands that it sends to
the gateway controller when
a control association
transitions to Out-of-Service
because of a failure.
Your Action
1.
Click Add new entry next to Gateway.
2.
Click H248 Options next to gateway.
3.
Expand H248 Options.
4.
Click Service Change next to H248 Options.
5.
Expand Service Change.
6.
Click Control Association Indications next to Service Change.
7.
In the Comment box, enter the comment.
8.
Expand Control Association Indications.
9.
Click Disconnect next to Control Association Indications.
10.
In the Comment box, enter the comment.
11.
From the Reconnect list, select the method and reason that
the virtual BGF includes in Registration Request
ServiceChange commands when it attempts to reregister
with the gateway controller or register with a new gateway
controller after the control association is disconnected.
12.
From the Controller Failure list, select the method and reason
that the virtual BGF includes in Registration Request
ServiceChange commands when it attempts to reregister
with the gateway controller or register with a new gateway
controller after the control association is disconnected.
1.
Click Down next to Control Association.
2.
In the Comment box, enter the comment.
3.
From the Administrative list, select the method and reason
that the virtual BGF includes in Unregistration Messages in
ServiceChange commands that it sends to the gateway
controller when a control association transitions to
Out-of-Service because of an administrative operation.
4.
From the Failure list, select the method and reason that the
virtual BGF includes in Unregistration or Notification Messages
in ServiceChange commands when a control association
transitions to Out-of-Service.
5.
From the Graceful list, select the method and reason that
the virtual BGF includes in Notification ServiceChange
commands that it sends to the gateway controller when the
control association transitions from In-Service to
Out-of-Service-Graceful.
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INTRUSION DETECTION PREVENTION DEVICES GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW CONTROLLER 2.0.4 -
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - SNMP AGENT GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1 and is the answer not in the manual?