Figure 5-2. Mx2820 Scu Menu Tree; Scu Menu Tree - ADTRAN MX2820 System Manual

SCU MENU TREE

Figure 5-2 shows the menu tree for the MX2820 System Controller Unit (SCU).
Unit Name
CLEI Code
Part Number
Serial Number
1. Configuration
Product Revision
Software Revision
Boot ROM Version
MAC Address
1. General
2. Provisioning
2. Network Management
3. SNMP
4. TL1
5. Smart Start
6. System Configuration Archive (SCA)
7. Service States
8. Reboot SCU
3. Status
1. Test Alarm Relays
4. Test
2. Self Test and Restart
* = Default Settings
61186003L1-1D
1. Craft Port Baud Rate
2. Interbank Comm. Mode
1. Management Ports
2. Date
Auto-Logoff
3. Time
4. Auto-Logoff
Auto-Logoff Time (30 min.*)
5. Restore Default Provisioning
6. Security Administration
7. Change [Currently Logged on]
Password
1. Ethernet Interface
2. Network Service Ports
3. IP Forwarding
4. FirmwareTFTP Server (0.0.0.0*)
5. SCA TFTP Server (0.0.0.0*)
6. IP Services Port Access Control
1. Trap Host 1 IP (0.0.0.0*)
2. Trap Host 2 IP (0.0.0.0*)
3. Trap Host 3 IP (0.0.0.0*)
4. Trap Host 4 IP (0.0.0.0*)
5. ifIndex Method
6. SCU Traps
7. System Name (SysName not set*)
8. System Location (SysLocation not set*)
9. System Contact (www.adtran.com*)
10. Read Community (public*)
11. Write Community (private*)
1. Smart Start
2. Copy Module Provisioning
3. Back-up SCU Provisioning to Linecards
4. Back-up Linecard Provisioning to SCU
1. SCA Autosave Provisioning
2. SCA Restore Provisioning Options
3. SCA Operations
SCU EQPT Functional Service State:
SCU EQPT Provisioned Service State:
1. Change SCU EQPT Provisioned Service State to OOS/IS

Figure 5-2. MX2820 SCU Menu Tree

Section 5, User Interface Guide - UIG-500, MX2820 Menu Tree
1. 9600*
2. 19200
3. 38400
4. 57600
5. 115200
HOST
CLIENT*
DISABLE
ENABLE*
1. Users Currently Logged On
2. Edit User Accounts
3. Create New User Account
4. Security Options
5. Restore Back to Default Accounts
6. Access Tech Support Account
7. RADIUS
8. SSH Configuration
1. TL1 Telnet Port (2000*)
2. TL1 Raw-ICP Port (2001*)
3. Secondary Telnet Port
(1024-65535) (2002*)
4. TL1 SSH Port
5. Secondary SSH Port
1. Sequential (RFC 2863)
2. Fixed (slot-based)*
1. ENABLE*
2. DISABLE
1. Intelligent NE*
1. Client Shelf Management
2. Expansion Shelf
2. System Name
3. TL1 Telnet Port
4. TL1-Raw-ICP Port
5.Exchange TL1 Ports
1. ENABLE*
1. Autosave System
2. DISABLE
2. Autosave Only If Prov Changes
3. Autosave Filename Prefix
4. Autosave Filename Suffix
5. Max Autosave File Instances
6. Autosave Time
7. Autosave Retries
1. Restore Provisions To SCU
2. Restore Provisions To Modules
1. SCA TFTP Server
2. SCA Remote Filename
3. SCA Autosave status
4. Perform TFTP SCA Save
5. Perform TFTP SCA Restore
6. TFTP SCA Save Status
7. TFTP SCA Restore Status
Shelf: 1
Unacknowledged Alarms: CRITICAL MAJOR
Hardware
Ethernet Link : Up
Alarm Relays
Critical
Major
Minor
External Inputs
Ext ACO
AUX #1 INPUT
AUX #2 INPUT
AUX #3A INPUT
AUX #3B INPUT
PWR Bus A
PWR Bus B
1. Password
1. Change Password/Access Privilege
2. Account Properties/
2. Enable/Disable User Account
Access Privilege
3. Delete User
1. Enable SNMP Security Account Access (No*)
2. Lock-Out User on Login Failure (No*)
3. Case Sensitive Password/User ID (Yes*)
4. Null Password Accepted (No*)
5. Number of Login Failure Before Lock-Out (5*)
6. Lock-Out Duration in Seconds (60*)
1. IP Address (0.0.0.0*)
2. Subnet Mask (255.255.255.0*)
3. Gateway (0.0.0.0*)
Ethernet Data Rate
4. Interface
Ethernet Link
MAC Address
1. ENABLE
2. DISABLE*
1. ENABLE
2. DISABLE*
1. ENABLE*
2. DISABLE
ADTRAN MX2820 System
TID: SysName not set
Status
LEDs
ACT : Grn/Ylw
ALM : Red
Inactive
Active
Inactive
Status Level
Inactive N/A
Inactive MAJOR
Inactive MAJOR
Inactive MAJOR
Inactive MAJOR
Active MAJOR
Inactive MAJOR
'?' - System Help Screen
1. Auto*
2. 10 Mbps
3. 100 Mbps
1. ENABLE*
2. DISABLE
1. ENABLE*
2. DISABLE
04/15/04 16:28
5-13