ADTRAN MX2820 M13 MUX Features

MX2820
LED STATUS FOR ACTIVE MUX
M13 MUX
ACT
P/N 1186002L1
CLEI: M3C3RG0A_ _
ALM
M13 MUX
1186002
DS3 STAT
ACT
ALM
STAT
DS3
TEST
DS3 TEST
STAT
DS1
TEST
DS1 STAT
DS1 TEST
LED STATUS FOR STANDBY MUX
ACT
ALM
DS3 STAT
DS3 TEST
DS1 STAT
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
DS1 TEST
HANDLING PRECAUTIONS REQUIRED.
MX2820 M13 MUX
! Green Normal (All OK)
!/! Green/Amber (Alternating) Normal and console open
Red Self-test failed
!
! Amber Software update in progress
!/! Red/Amber (Alternating) Self-test failed and console open
Red (Flashing) Module has failed
Green No critical, major, or minor alarms
!
! Red Major or minor alarm in progress
Red (Flashing) Critical alarm in progress
Green Normal (DS3 OK)
!
! Red AIS, OOF, RAI, Idle alarms
Red (Flashing) DS3 LOS or DS3 Failure (critical)
Red (Flashing once per event) Single/Burst DS3 code violations
!/! Red/Green (Alternating) DS3 XCV threshold exceeded
" Off No DS3 tests in progress
Amber In test (locally originated)
!
Amber (Flashing) In test (remotely originated)
" Off All DS1s are disabled
! Green Enabled DS1s normal (All OK)
Red Non-critical DS1 alarm (CAIS, LAIS)
!
Red (Flashing) LOS on an enabled line (critical DS1
alarm; non-critical system alarm)
Red (Flashing once per event) Single/Burst RX DS1 code violation
Red/Green (Alternating) DS1 XCV threshold exceeded
!/!
" Off No DS1 tests in progress
Amber In test (locally originated)
!
Amber (Flashing) In test (remotely originated)
Green (Flashing) Normal (All OK)
Amber Software update in progress
!
Red Failure
" Off Permanent state during standby
" Off Normal (DS3 OK)
Red (Flashing) In test (remotely originated)
" Off Permanent state during standby
" Off Normal (DS1s OK)
Red (Flashing) DS1 Failure
" Off Permanent state during standby
DESCRIPTION
The MX2820 M13 MUX is a plug-in unit for the MX2820 chassis that provides an M13
multiplexer function to the MX2820 system. Two MX2820 M13 MUX cards are used together
to provide a redundant M13 multiplexer circuit. The MX2820 M13 MUX:
♦
Provides 1:1 redundancy
♦
Meets the requirements for NEBS Level 3.
INSTALLATION AND TURNUP
After unpacking the unit, inspect it for damage. If damage is found, file a claim with the carrier
and then contact ADTRAN Customer Service. Refer to the Warranty Statement on this Job Aid.
This module occupies a MUX slot in the MX2820 chassis. To install the M13 MUX in the
chassis, perform the following steps:
1. Pull the ejector tab into the down position and gently but firmly push the MUX into the
selected MUX slot. Simultaneous thumb pressure at the top and at the bottom of the unit
will ensure a good seat of the MUX into the backplane connector.
2. Push the ejector tab up and closed against the front panel.
Upon installation, the MUX will begin a self-test. This is followed with the LEDs reflecting
the true state of the hardware.
OPERATIONAL SPECIFICATIONS
♦
Operates from A or B input voltage power feeds.
♦
–48 VDC Systems: –42 VDC to –56 VDC
♦
–24 VDC Systems: –22 VDC to –27 VDC
♦
+24 VDC Systems: +22 VDC to +27 VDC
♦
Operates over extended temperature range of –40ºC to +50ºC without fans or –40ºC to +65ºC
with fans.
♦
Storage –40ºC to +85ºC. Relative humidity to 95 percent, noncondensing.
COMPLIANCE
♦
The MX2820 M13 MUX complies with UL 60950, NEBS Level 3, and GR-1089-CORE.
♦
The MX2820 M13 MUX is intended for installation in restricted access areas only.
♦
The MX2820 M13 MUX is intended for installation in a Type "B" or "E" enclosure.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN could void the user's authority
to operate this equipment.
Code
Power Code
Telecommunication Code (TC)
Installation Code (IC)
PROVISIONING
All provisioning of the MX2820 M13 MUX will be handled through the SCU. The menu tree
on the reverse of this Job Aid provides the options and default settings for the MX2820 M13
MUX.
61186002L1-22E
0501
Input Output
C C
– –
A –