Setting Re-Entry Signals - Sony MKS-X1115 User Manual

M/E Config is set to Multi Program 2 and recalled DME effects on two channels are different types
M/E Split DME usage on
target M/E
Off Main: Not used
Sub: Not used
Main: Used
Sub: Not used
Main: Not used
Sub: Used
Main: Used
Sub: Used
a) Used on the 2nd channel DME when two DMEs are used on the main side only or on the sub side only.
b) If DME effects recalled on main and sub are the same type (both DME wipes or image effects), the 2nd channel DME is on the sub side.
c) If DME effects recalled on main and sub are different types (DME wipe/image effect or image effect/DME wipe), the 1st channel DME is on the sub side.

Setting Re-Entry Signals

You can send a re-entry signal or internal signal for a
target box to the cross-point box and then select that
signal on the bus of each box or output that signal on the
output (Output) of each box. You can set the signals to
send to the cross-point box. For the cross-point box, the
signals to use must be assigned.
The number of assignable signals will vary depending on
the system signal format.
2160P format:
For an M/E box: 12 (max)
For a cross-point box: 16 (max)
1080P, 1080i, or 720P format:
For an M/E box: 24 (max)
For a cross-point box: 32 (max)
Notes
• When the output from frame memory or a clip player
sent to the cross-point box is selected on a bus, one line
is dropped from the image.
• In a 1M/E box switcher configuration, this setting is not
required.
• For a cross-point box, set the required signals from
among the re-entry signals and input signals.
• Signals assigned using the Home > Setup > Switcher >
Box Settings > Re-Entry Source Assign menu
(19103.52) have the following restrictions.
Target region when Prevention of picture flash when recalling DME
recalling DME effects
Main 1st ch
Target M/E Main&Sub Required setting
Target M/E Main Required setting
Target M/E Sub –
Target M/E Main&Sub Required setting
Target M/E Main Required setting
Target M/E Sub –
Target M/E Main&Sub Required setting
Target M/E Main Required setting
Target M/E Sub –
Target M/E Main&Sub Required setting
Target M/E Main Required setting
Target M/E Sub –
404
Sub 1st ch
Required
c)
setting
–
Required setting
Required
c)
setting
–
Required
c)
setting
Required
c)
setting
–
Required setting
Required
c)
setting
–
Required
c)
setting
- M/E-IP input/output type box signals
When the system signal format is 2160P, ancillary
data is deleted from signals assigned to No. 1, 2, 7,
and 8.
- M/E box signals
When an assigned frame memory signal or clip player
signal is used on the cross-point box, the ancillary
data is deleted from that signal.
– Cross-point box signals
When an assigned input signal, frame memory signal,
or clip player signal is used, the ancillary data is
deleted from that signal.
1
Open the Home > Setup > Switcher > Box Settings >
Re-Entry Source Assign menu (19103.52).
2
Select the number of the target signal to set.
The types of signals that can be assigned are
displayed in white in [Source Assignable Groups].
3
Press the [Edit Source] button.
The [Select Source] window appears.
4
Set the button for the target signal to the on state.
Select a tab to change the type of signal to display.
[M/E-1] tab: M/E-1 block re-entry signals
[M/E-2] tab: M/E-2 block re-entry signals
2nd ch (DME External)
–
a)
Required setting
a)
Required setting
–
a)
Required setting
–
–
–
a)
Required setting
–
–
–