Margin (Left/Right); Vacuum Fan; Feed Speed; Maps - MIMAKI TxF150-75 Operation Manual

Select [DRYING TIME] and press the
3
[ENTER] key.
Set each setting item, and then press the
4
[ENTER] key.
• Scanning setting value: Host or 0.0–9.9 sec.
• Print end setting value: Host or 0–120 min.
• Item selection: Select with [  ] / [  ]
• Time setting: Set with [  ] / [  ]
• To give priority to RIP settings, use "Host" as the
setting value.

Margin (left/right)

Set a non-printing area along the left and right edges of
the media.
This is an offset value relative to the standard 15 mm
margin.
• Margins cannot be set with the included RIP soft-
ware (RasterLink). Setting the machine setting to
"Host" when RasterLink is used will print with
"Margins for right and left offset value=0 mm."
• The margin setting is applied when the media
width is detected.
With the screen in local mode, select
1
[MENU] > [SETUP], and then press the
[ENTER] key.
• SETUP options are displayed.
Select a SETUP option from 1 to 4 and
2
press the [ENTER] key.
• The SETUP menu is displayed.
Select [MARGIN / LEFT] or [MARGIN /
3
RIGHT] and press the [ENTER] key.
Select a setting value and press the
4
[ENTER] key.
• Setting value: HOST / -10 to 85 mm
• To give priority to RIP settings, use "Host" as the
setting value.
• When the media holder is used in printing, set-
ting the right and left margin to -5 mm or less
may cause printing to start on the media holder.

Vacuum fan

Sets the force with which the medium is held down.
Setting suitable vacuum strength for the media can
prevent print errors due to the media lifting up.
With the screen in local mode, select
1
[MENU] > [SETUP], and then press the
[ENTER] key.
• SETUP options are displayed.
Select a SETUP option from 1 to 4 and
2
press the [ENTER] key.
• The SETUP menu is displayed.
Select [VACUUM] and press the [ENTER]
3
key.
Select a setting value and press the
4
[ENTER] key.
• Setting value: HOST / WEAK / STANDARD /
STRONG

Feed speed

Changes the media feed speed in printing and other
tasks.
With the screen in local mode, select
1
[MENU] > [SETUP], and then press the
[ENTER] key.
• SETUP options are displayed.
Select a SETUP option from 1 to 4 and
2
press the [ENTER] key.
• The SETUP menu is displayed.
Select [FEED SPEED] and press the
3
[ENTER] key.
Select a setting value and press the
4
[ENTER] key.
• Setting value: HOST / 10–200%
• To give priority to RIP settings, use "Host" as the
setting value.
• Depending on print conditions, the speed may
not vary for certain settings.

MAPS

MAPS (Mimaki Advanced Pass System) evens out ink
ejection at pass boundaries to reduce banding between
passes. This function enables you to change the extent to
which MAPS is applied.
• MAPS provides two setting options: "AUTO" and
"MANUAL." Because processing most suitable
for the printing conditions is applied with MAPS,
normally use the default option of "AUTO."
• This function requires Mimaki driver Ver. 4.2.0 or
higher.
• Changing the MAPS settings may change the
color tone. Check the results before use.
• MAPS may not be effective when printing cer-
tain images. Check the results before use.

Auto cleaning

Can be set so that cleaning is performed automatically
after a set number of files, media length, or time to date.
This enables consistent printing, with heads kept clean.
Three auto cleaning options are available, as follows.
FILE Auto cleaning is performed after the
specified print volume.
LENGTH Auto cleaning is performed after the
machine has fed the specified length of
media.
TIME Auto cleaning is performed after the
specified time has elapsed.
Chapter 3 Settings
3-5
1
2
3
4
5
6