Setting The Key Buzzer; Setting View Feed; Setting Space Feed Mode - MIMAKI TxF150-75 Operation Manual

Chapter 3 Settings
Place the ink pack and the ink IC chip in
2
the eco ink cartridge case.
P.1-11 「Replacing Ink」 ）
•（
Insert the eco ink cartridge in the ink
3
supply unit.
In LOCAL mode screen, select [MENU] >
4
[Machine Setup], then press the [ENTER]
key.
• The Machine Setup menu is displayed.
Select [Eco cartridge] > [Case Weight],
5
then press the [ENTER] key.
Select the required ink slot, then press the
6
[ENTER] key.
• The selected slot is highlighted.
Enter the measured weight of the eco ink
7
cartridge case, then press the [ENTER]
key.
• Check the following when "ERROR614
Preservation Failure" appears:
(1)Check to confirm that the eco ink cartridge
was fully inserted.
(2)Check to confirm the ink IC chip was installed
correctly.
Correcting the Ink Cartridge Case Weight
When the remaining ink level in the eco ink cartridge
reaches a preset level, [Ink Level Low], [Ink Near End],
[Ink Level End], or [Ink End] appears on the display. The
weight may differ from the actual weight, so the weight of
the eco ink cartridge should be corrected.
• If non-actual weights are registered repeatedly,
the ink IC chip can no longer be used.
• Continuous printing is not possible when the
warning is displayed.
• Replace with a new ink pack when "Replace Ink-
pack" is displayed.
A warning appears on the display.
1
Remove the eco ink cartridge case in the
2
indicated ink slot, and measure the weight.
• Weight with the ink pack inserted.
Insert the eco ink cartridge in the ink
3
supply unit.
• The cartridge weight screen appears.
Enter the measured weight of the eco ink
4
cartridge, then press the [ENTER] key.
• The remaining ink amount of the ink pack is
calculated and saved in the ink IC chip.
3-10
• The weight of the eco cartridge can be registered
as follows:
(1) In LOCAL mode screen, select [MENU] >
[Machine Setup], then press the [ENTER] key.
••The Machine Setup menu is displayed.
(2) Select [Eco cartridge] > [Cartridge Weight],
then press the [ENTER] key.
(3) (3)Select the required ink slot, then press the
[ENTER] key.
•The selected slot is highlighted.
(4) Enter the measured weight of the eco ink
cartridge, then press the [ENTER] key.
• Check the following when "ERROR614
Preservation Failure" appears:
(1)Check to confirm that the eco ink cartridge
was fully inserted.
(2)Check to confirm the ink IC chip was installed
correctly.

Setting the key buzzer

You can turn off the buzzer sound that is played when
keys are pressed.
With the screen in local mode, select
1
[MENU] > [MACHINE SETUP], and then
press the [ENTER] key.
• The MACHINE SETUP menu is displayed.
Select [KEY BUZZER] and press the
2
[ENTER] key.
Select a setting value and press the
3
[ENTER] key.
• Setting value: ON / OFF
• Setting the buzzer to OFF does not disable
sounds for errors, warnings, or completion of
operation.

Setting view feed

Sets whether media feeding is performed in order to
check test printing results, for example.
With the screen in local mode, select
1
[MENU] > [MACHINE SETUP], and then
press the [ENTER] key.
• The MACHINE SETUP menu is displayed.
Select [VIEW FEED] and press the [ENTER]
2
key.
Select a setting value and press the
3
[ENTER] key.
• Setting value: ON / OFF

Setting space feed mode

Alters the feed method for blank space included in image
data if there is no data to print. Data with wide margins
can be printed in less time when set to [CONTINUOUS].