Inserting Ink Cartridges; Precautions On Handling Ink Cartridges - MIMAKI TxF150-75 Operation Manual

Color inkjet printer
Table of Contents

Advertisement

Chapter 1 Before Use
Connecting a LAN cable
Connect a PC to this product using a LAN cable. Insert a
LAN cable until it engages with a click.
• Do not unplug the cable while data is being
transferred.
 Network Connection Precautions
Make sure the network is set up as follows: Printing is not
possible if the network is not set up correctly.
• Use a Category 6 or higher LAN cable.
• The PC used to transfer print data must be located on
the same network as this product. This product cannot
be connected via a router.
• Use a 1000BASE-T compatible computer or switching
hub. Printing requires 1000BASE-T support.
 Checking the LAN connection
Check the display on this product.
1
• Local guidance can be used for checking. Printing
is not possible if "100Mbps", "10Mbps", or "No
Connect" is displayed. Event email can be used.
INFORMATION
LAN Status
Check the lamp on the LAN connector.
2
• The LAN connector lamp illuminates when the
machine is running.
Color
Status
Green Illuminated Connected via 1000BASE-T
Off
Connected via a network other than
1000BASE-T
1,000 Mbps is not supported if only the
orange lamp is illuminated or flashing.
Check the specifications for the PC,
peripheral devices, and cable.
Orange Illuminated Linked up (connected).
Flashing
Data being received
Off
Link down (not connected)
1-8
1000Mbps
Overview
Inserting Ink
Cartridges

Precautions on handling ink cartridges

• Ink cartridges are labeled with precautions about
the ink. Thoroughly read them and make sure you
understand the contents.
• Before using ink and maintenance liquid, be sure
to read the Safety Data Sheet (SDS) and
instruction manual for ink.
japan.mimaki.com/supply/sds/)
• Also be sure to use ink cartridges recommended
by Mimaki.
• Keep ink away from open flame. Also, be sure
that the room is well ventilated when using or
handling ink.
• Immediately wipe off any ink, maintenance liquid,
waste ink, or other liquid used with the machine
that comes into contact with your skin using a
cloth. Wash with soap and rinse with plenty of
water. Failure to observe these instructions may
result in skin inflammation. If your skin becomes
irritated or painful, seek medical attention
immediately.
• If ink, maintenance liquid, waste ink, or any other
liquid used with the machine comes into contact
with your eyes, rinse immediately with plenty of
clean water. Rinse for at least 15 minutes. If you
wear contact lenses and they can be easily
removed, remove after rinsing for at least 15
minutes with clean water. Rinse thoroughly,
including the undersides of your eyelids. Failure to
observe these instructions may result in blindness
or impaired vision. If your eyes become irritated or
painful, seek medical attention immediately.
• If ink, maintenance liquid, waste ink, or any other
liquid used with the machine enters your mouth or
is swallowed, gargle with water immediately. Do
not induce vomiting. Seek medical attention
promptly. Inducing vomiting may cause liquid to
enter the airway.
• If a large amount of vapor is inhaled, move to a
well-ventilated area, keep warm, and rest in a
posture that allows easy breathing. If the condition
does not improve, seek medical attention
promptly.
• Then contact the emergency number written on
the SDS.
  Osaka072-727-2499: Available 24 hours a
day
  Tsukuba029-852-9999: Available from 9:00
a.m. to 9:00 p.m.
• The machine's safety rating is based on using ink
recommended by Mimaki. To ensure safe
operation, use ink recommend by Mimaki.
• If the ink cartridges are brought from a cold place
to a warm place, leave them at room temperature
for at least three hours before use.
• Open the ink cartridges just before installation. If
they are left open over an extended period, it may
not be possible to print normally.
• Store ink cartridges in a cool, dark place.
• Keep ink cartridges and waste ink tanks out of the
reach of children.
• Once an ink cartridge is opened, use up the ink
within one month. Printing quality declines after
cartridges have been open over an extended
period.
(https://

Advertisement

Table of Contents
loading

Table of Contents