Uat Ground Uplink Definition Parameters - Viavi ATC-5000NG Operation Manual

5.7.4.16.8 AUXILIARY STATE VECTOR PAYLOAD MESSAGE ELEMENT
Command Syntax:
Description:
Numeric:
Example:
5.7.4.16.9 TARGET STATE PAYLOAD MESSAGE ELEMENT
Command Syntax:
Description:
Numeric:
Example:
5.7.4.16.10 RETRIGGER LONG ADS-B MESSAGE DATASET SIZE
Command Syntax:
Description:
Default:
Example:
5.7.5

UAT GROUND UPLINK DEFINITION PARAMETERS

The following set of commands allows the user to define a ground uplink UAT message. See section
5.11.8. UAT Scenario Definition for an example.
5.7.5.1 UAT-SPECIFIC HEADER
5.7.5.1.1 APPLICATION DATA VALID
Command Syntax:
Description:
Default:
Example:
5.7.5.1.2 GROUND STATION LATITUDE
Command Syntax:
Description:
Numeric:
Example:
Rev. L0
February 2020
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder
no>{:PLASV}SP<numeric>CR
This command sets the auxiliary state vector payload message element of the specified intruder.
This command applies to ADS-B Messages with payload type code of '1', '2', '5' and '5.6.' The
data message is padded on the right with zeros for a length 10 hexadecimal ASCII. The <intruder
no> specifies the number of the intruder in the channel grouping specified.
0 to FFFFFFFFFF (10 hexadecimal ASCII)
:ATC:SCE:STAT:1:PLASV B254\r
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder
no>{:PLTS}SP<numeric>CR
This command sets the intruder state payload message element of the specified intruder. This
command applies to ADS-B Messages with payload type code of '3', '4' and '6.' The data
message is padded on the right with zeros for a length 10 hexadecimal ASCII. The <intruder no>
specifies the number of the intruder in the channel grouping specified.
0 to FFFFFFFFFF (10 hexadecimal ASCII)
:ATC:SCE:STAT:1:PLTS C84397\r
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder no>{:DSSIZE}SP{48 |64
|80 |83 |107}CR
This command sets the dataset size for the ADS-N long message data used for UAT Special Test
Mode (Retrigger Long ADS-B Message) of the specified intruder. The <intruder no> specifies the
number of the intruder in the channel grouping specified.
48
:ATC:SCE:STAT:1:DSSIZE 64\r
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder
no>{:UAT}{:GUS}{:ADVALID}SP{ON | OFF}CR
This command enables or disables the Application data valid condition of the specified intruder.
The <intruder no> specifies the number of the intruder in the channel grouping specified.
Off
:ATC:SCE:STAT:1:UAT:GUS:ADVALID ON\r
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder no>
{:UAT}{:GUS}{:LAT}SP<numeric>CR
This command sets the latitude of the ground station. The <intruder no> specifies the number of
the intruder in the channel grouping specified.
-90 to 90 degrees (double ASCII)
:ATC:SCE:STAT:1:UAT:GUS:LAT 30\r
ATC-5000NG ATC/DME Test Set Operation Manual
Subject to Export Control. See Cover Page for details.
Operation, Remote Operation
Scenario Commands
1-2-5
Page 95