Viavi ATC-5000NG Operation Manual page 259

5.7.5.1.3 GROUND STATION LONGITUDE
Command Syntax:
Description:
Numeric:
Example:
5.7.5.1.4 POSITION VALID
Command Syntax:
Description:
Default:
Example:
5.7.5.1.5 SLOT ID
Command Syntax:
Description:
Numeric:
Example:
5.7.5.1.6 TIS-B SITE ID
Command Syntax:
Description:
Numeric:
Example:
5.7.5.1.7 UTC COUPLED CONDITION
Command Syntax:
Description:
Example:
5.7.5.2 GROUND UPLINK APPLICATION DATA
5.7.5.2.1 INFORMATION FRAMES QUANTITY
Command Syntax:
Description:
Numeric:
Example:
1-2-5
Page 96
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder no>
{:UAT}{:GUS}{:LONG}SP<numeric>CR
This command sets the longitude of the ground station. The <intruder no> specifies the number
of the intruder in the channel grouping specified.
-180 to 180 degrees (double ASCII)
:ATC:SCE:STAT:1:UAT:GUS:LONG -45\r
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder
no>{:UAT}{:GUS}{:POSVALID}SP{ON | OFF}CR
This command enables or disables the Position valid condition of the specified intruder. The
<intruder no> specifies the number of the intruder in the channel grouping specified.
Off
:ATC:SCE:STAT:1:UAT:GUS:POSVALID ON\r
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder
no>{:UAT}{:GUS}{:SLOTID}SP<numeric>CR
This command sets the time slot where the Ground Uplink Message transmission occurs. The
<intruder no> specifies the number of the intruder in the channel grouping specified.
0 to 31 (decimal ASCII)
:ATC:SCE:STAT:1:UAT:GUS:SLOTID 22\r
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder
no>{:UAT}{:GUS}{:TISBID}SP<numeric>CR
This command sets the TIS-B Site ID of the specified intruder. The <intruder no> specifies the
number of the intruder in the channel grouping specified.
0 to 31 (decimal ASCII)
:ATC:SCE:STAT:1:UAT:GUS:TISBID 12\r
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC: |:DYN: |:DYNAMIC:}<intruder
no>{:UTC}SP{ON | OFF}CR
This command enables or disables the UTC coupled condition of the specified intruder. The
<intruder no> specifies the number of the intruder in the channel grouping specified.
:ATC:SCE:STAT:1:UTC ON\r
{:ATC |:ATC5000NG}{:SCE |:SCENARIO}{:STAT: |:STATIC:}<intruder
no>{:UAT}{:GUS}{:IFRAME}{:NIFRAMES}SP<numeric>CR
This command sets the quantity of information frames for the selected intruder. The <intruder
no> specifies the number of the intruder in the channel grouping specified.
0 to 255 (decimal ASCII)
:ATC:SCE:STAT:1:UAT:GUS:IFRAME:NIFRAMES 7\r
ATC-5000NG ATC/DME Test Set Operation Manual
Subject to Export Control. See Cover Page for details.
Operation, Remote Operation
Scenario Commands
Rev. L0
February 2020