Kärcher KM 105/100 R G Manual page 48

9
Brushpos. not ok
Hours: xxxxxhym+
10
RBroompos.not ok
Hours: xxxxxhym+
11
LBroompos.not ok
Hours: xxxxxhym+
12
SBroompos.not ok
Hours: xxxxxhym+
13
Seat switch open
Hours: xxxxxhym+
14
Usable sweeping
brush <25%
15
MF-module not
ready to use x
16
Motorhood open!
Hours: xxxxxhym+
17
Engine support OFF
Hours: xxxxxhym+
18
Low battery
Hours: xxxxxhym+
19
Battery flat!
Charge externally!
20
Firmware update
firmware update!
21
V-engine error
OFF for restart
22
Call service!
+xx-xxxx-xx-xxxx
48
Is displayed when the roller brush cannot move to the
factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying
Is displayed when the right side brush cannot move to
the factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying or the right side
brush may not be raised
Is displayed when the optionally available left side brush
cannot move to the factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying or the left side
brush may not be raised
Is displayed when the optionally available sickle brush
cannot move to the factory-set end position.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying or the sickle brush
may not be raised
Appears if the seat is left for more than 1.5 seconds in
drive mode.
– Combustion motor switches off, all brushes and the
roller brush that are lowered to the ground are raised au-
tomatically
Appears if the roller brush has reached its wear limit.
– The appliance is ready for operation, however, the
sweeping result may be dissatisfying
Appears if the control panel has no connection to the
machine control.
– The operation of the appliance is disabled
Appears if the left side cover is not properly locked in
place.
– The operation of the appliance is disabled
Appears if the battery is not sufficiently charged during
operation.
– When driving uphill, the support of the combustion mo-
tor from the battery is disabled
Appears if the battery voltage in the sweeping mode is
so low that a start of the combustion engine is no longer
possible after switching off the appliance.
– All sweeping functions are switched off, the appliance
is still running
Appears as soon as the programme selector switch is
turned away from the OFF position and it is recognised
that the minimum battery voltage for starting the com-
bustion engine is not reached.
– The operation of the appliance is disabled to protect
the battery
Appears if the machine control has detected a safety-
critical error during the self test.
– The operation of the appliance is disabled
The monitoring system for the control of the combustion
engine has detected a severe error.
– The combustion engine no longer shuts off
The inspection interval has lapsed. This message ap-
pears upon every start-up of the appliance.
– The appliance remains fully operational
 Confirm the message with the OK key (delete).
 Turn the programme selector switch to position
C (drive).
 Change to the desired sweeping programme
again.
 Confirm the message with the OK key (delete).
 Turn the programme selector switch to position
C (drive).
 Change to the desired sweeping programme
again.
 Confirm the message with the OK key (delete).
 Turn the programme selector switch to position
C (drive).
 Change to the desired sweeping programme
again.
 Confirm the message with the OK key (delete).
 Turn the programme selector switch to position
C (drive).
 Change to the desired sweeping programme
again.
 Sit on the driver's seat.
Note: The selected sweeping / transport opera-
tion starts fully automated.
 Replace the roller brush as soon as possible to
achieve a good sweeping result.
 Perform a programme selector switch reset
(OFF position).
 Completely close and lock the engine bonnet in
place.
 Turn the programme selector switch to "ON".
Note: The message disappears. The appliance
is ready for operation.
 Confirm the message with the OK key (delete).
 Drive the appliance on a level ground using the
combustion motor for a longer period of time.
This charges the battery.
Note: The message can no longer be confirmed.
 Drive the appliance on a level ground using the
combustion motor for a longer period of time.
This charges the battery.
 Disconnect the battery and connect it with the
correct polarity to an approved charger for
charging.
 Call service!
 CAUTION! Move the main switch to the "0" po-
sition to switch the engine off!
 In addition:
Perform a programme selector switch reset
(OFF position).
 Subsequently:
Set main switch to "1".
Change to the desired sweeping programme
again.
 Confirm the message with the OK key (delete).
 Contact your local service for inspection under
the displayed phone number.
21
-
EN