Kärcher KM 105/100 R G Manual page 35

Available menu items are:
>Blower/pump locked/enabled<
Without function
>Enable delete day counter<
It can be selected whether the operator is
able to reset the day counter.
>Programming yes/no<
As the last menu item the >Program-
ming< display with the seconds counted
down appears.
 To transfer the settings to the yellow in-
telligent key:
While the seconds are counted down,
select >YES< with the direction key "to
the right" and confirm with the "OK" key.
Note: Thereby the settings made are
transferred to the yellow intelligent key
and are enabled.
Notes on operation using the KIK-key
(Kärcher Intelligent Key)
 Make sure that there is no more than 1
KIK-key near the control panel.
 If this should be the case, the fault P/11
may appear on the display.
Safety Devices
WARNING
This appliance is equipped with a variety of
safety installations. The proper function of
every safety installation must be checked
prior to operation and must NOT be over-
ridden!
Main switch
The main switch on the control panel
serves the immediate shutdown of the
combustion engine and the electrical drives
in case of emergencies and may only be
used for this purpose.
Bonnet left side (engine bonnet)
The left engine bonnet is equipped with a
safety installation that switches off the run-
ning combustion engine when opened and
issues a warning message on the display.
Emergency switch-off (diesel engine)
The emergency stop is located at the side
of the engine.
Actuating the emergency stop:
 Open the engine hood.
 Push down the red lever (1).
 For resetting, push lever (2) to the right.
Waste container (high emptying system)
The high emptying system is equipped with
a safety installation that blocks the sweep-
ing operation during the emptying proce-
dure.
Button for two-hand operation
Appliances with a high emptying system
are equipped with a button for two-hand op-
eration.
 For emptying the waste container, the
button must be pressed together with
the keys of the high emptying system.
Safety support waste container (high
emptying system)
DANGER
Risk of injury!
 When working on the high emptying
system, completely lift and secure the
waste container.
 Perform the safeguarding only from
outside the hazard zone.
During any work underneath the lifted
waste container, the lifting cylinder must be
secured by means of a safety support.
The safety support is attached to the cross-
beam by means of 2 star screws for stor-
age.
 Remove safety support, in order to do
this, unscrew 2 star screws.
 Insert safety support into the piston rod
for the lifting cylinder and secure it.
Note: The round notch must point up-
wards.
8
-
EN
Before Startup
Remove the appliance cover
ATTENTION
The appliance cover with the seat may only
be removed by the authorised aftersales
service for repair or maintenance work.
The description can be found in the service
manual.
Opening/closing the engine bonnet
ATTENTION
The bonnet may only be opened when the
programme selector switch is in the "OFF"
position and the KIK-key is removed.
Opening the engine bonnet during opera-
tion of the appliance is prohibited.
For refuelling and maintenance work the
left engine bonnet must be opened.
 Grab the front of the engine bonnet on
the recessed grip, unlock it towards the
top and swivel it to the side.
Note: The engine bonnet is equipped with
a safety installation that switches off the
running combustion engine when opening
the bonnet and issues a warning message
on the display. If the bonnet is not properly
closed, the engine cannot be started.
If a warning message is pending, it can be
reset as follows:
 Completely close the bonnet (locking in
place).
 Turn the programme selector switch to
"ON".
 Sit on the driver's seat.
Unloading tips
DANGER
Risk of injury, risk of damage!
 Observe the weight of the appliance
when you load it!
 Do not use a forklift truck to unload the
machine as this may damage it.
ATTENTION
Charge the battery before commissioning
the machine.
Net weight (transport weight)
The net weight is between 400 kg and
608 kg depending on the unit model *.
Refer to chapter "Technical data".
* If upgrade kits are installed, the weight is
respectively higher.
 When loading the appliance a suitable
ramp must be used!
 If the machine is delivered on a pallet,
you must create an unloading ramp us-
ing the boards provided.
To unload the machine, proceed as follows:
 Cut plastic packing belt and remove foil.
35